Criteria

Text:
Topic:
Content:
Display:

Results

Viewing 151 to 180 of 9893
CURRENT
2017-03-24
Standard
AMS5085J
This specification covers a carbon steel in the form of sheet, strip, and plate.
CURRENT
2017-03-24
Standard
AMS5339G
This specification covers an alloy steel in the form of investment castings.
CURRENT
2017-03-23
Standard
AMS4284K
This specification covers an aluminum alloy in the form of permanent mold castings.
CURRENT
2017-03-23
Standard
AMS5824F
This specification covers a corrosion-resistant steel in the form of welding wire.
CURRENT
2017-03-21
Standard
AMS03_1A
This SAE Standard specifies the processes and type of impregnant which can be used when impregnating castings for the following purposes: a. For the recovery of ferrous and non-ferrous castings containing micro porosity, where pressure tightness is mandatory. b. For sealing castings/sinter metal components to improve corrosion resistance and/or to render the surface suitable for subsequent surface treatment.
CURRENT
2017-03-21
Standard
AMS03_4A
This SAE Standard specifies the special treatments and precautions that are to be observed when protective and other surface treatments are applied to items, including springs, made from steel of specified maximum tensile strength exceeding 1450 MPa. The requirements of this Standard qualify those in process specifications and override the latter where there is conflict. The Standard also gives advice on design, manufacture, and preparation of items prior to cleaning and protection.
2017-03-21
WIP Standard
B17AA
This Aerospace Recommended Practice (ARP) describes design and processing considerations for the shot peening process when AMS2430 or AMS2432 are specified.
CURRENT
2017-03-21
Standard
AMS03_3A
This SAE Standard specifies the requirements for the application of sprayed metal coatings of aluminum, zinc, or aluminum-zinc based alloys for the protection of aluminum alloys against corrosion. It does not cover the metal spraying of aluminum armour materials, which should be treated in accordance with the requirements of Def Stan 08-39.
CURRENT
2017-03-21
Standard
AMS03_2A
This SAE Standard specifies processes for the cleaning of metal surfaces to remove any extraneous or undesirable material or deposits at any stage of manufacture, storage or service and for the preparation of these surfaces for further treatment. Any necessary stress-relieving treatments are also included. This Standard does not override special preparatory procedures specified in individual Defence Standards, Defence Specifications, DTD Process Specifications, DG Ships Specifications and Naval Defence Standards. It also does not cover cleaning operations associated with the maintenance of internal combustion engines, the preliminary removal of heavy deposits of oil, grease, or dirt accumulated during operational service, preparations for welding and the cleaning of electrical contacts.
2017-03-21
WIP Standard
AMS5707N
This specification covers a corrosion and heat-resistant nickel alloy in the form of bars, forgings, flash welded rings, 3.25 inches (82.6 mm) and under and stock of any size for forging and for flash welded rings. (See 8.5).
CURRENT
2017-03-21
Standard
AS9955A
CURRENT
2017-03-17
Standard
AMS2451/4C
This specification establishes the requirements for brush plating of cadmium by electrodeposition.
CURRENT
2017-03-17
Standard
ARP6903
The intent of this ARP is to provide guidance to assist users in choosing compatible component finishes/platings to achieve the best corrosion resistance performance for compatible components/couples. This SAE Recommended Practice is intended as a guide toward standard practice and is subject to change to keep pace with experience and technical advances. A galvanic compatibililty table is provided to assist with the compatible plating/finish selection. Specific plating performance parameters for each individual plating and each connector/accessory specification have also been provided to assist the product user with compatible plating/finish selection.
2017-03-16
WIP Standard
ARP1820C
This practice provides a method of evaluating microhardness and microstructure very close to the surface of a disk specimen. It is useful for process control in heat treatment of steel parts to detect nitriding and carburization as well as decarburization and excessive intergranular oxidation. It also may be valuable for other evaluations, e.g., plated coatings and other materials.
CURRENT
2017-03-14
Standard
AS36102B
This SAE Aerospace Standard (AS) specifies the testing methods to be used to substantiate performance of air cargo containers, pallets and nets (Unit Load Devices) for airworthiness approval in accordance with NAS 3610 or AS36100.
2017-03-13
WIP Standard
AMS3056C
This specification covers the requirements for a refined paraffinic petroleum-base lubricant. Primarily as a lubricant in spin axis bearings of gyroscopes, accelerometers, and similar bearing applications.
2017-03-13
WIP Standard
ARP5316E
This SAE Aerospace Recommended Practice (ARP) addresses the general requirements for data recording procedures, packaging, and storing of elastomeric seals and seal assemblies which include an elastomeric element prior to the seal being assembled into hardware components. It applies specifically to those elastomeric seals and seal assemblies packaged shortly after manufacture. The storage period prior to installation of the elastomeric seals and seal assemblies into hardware components is commonly referred to as shelf life.

The information contained in this ARP is intended to be utilized by those organizations who do not have specific requirements or recommendations already in place for the control of elastomeric seals and seal assemblies. This ARP can be specified in control, storage, and procurement documents.

CURRENT
2017-03-08
Standard
AMS2418J
This specification covers the requirements for electrodeposited copper.
CURRENT
2017-03-07
Standard
AMS4473A
This specification covers an aluminum alloy in the form of plate 0.750 to 1.500 inch (19.05 to 38.10 mm), inclusive, in nominal thickness.
CURRENT
2017-03-03
Standard
AMS3025D
This specification covers two types of polyalkylene glycol in the form of a liquid.
2017-03-02
WIP Standard
AMS6532G
This specification covers a premium aircraft-quality alloy steel in the form of bars, forgings, and forging stock.
2017-03-02
WIP Standard
ARP1962B
This document requires that the company (facility) employing the personnel ensure a verifiable program of on-the-job training, experience, education, classroom instruction, and evaluation of personnel using either company-created programs or programs described herein. It describes the requirements for training and approval of personnel performing certain heat-treating and associated operations. It also establishes that only approved personnel may perform or monitor the functions listed for the processes and materials listed.
CURRENT
2017-03-02
Standard
J3108_201703
This recommended practice prescribes clear and consistent labeling methodology for communicating important xEV high voltage safety information. Examples of such information include identifying key high voltage system component locations and high voltage disabling points. These recommendations are based on current industry best practices identified by the responder community. Although this recommended practice is written for xEVs with high voltage systems, these recommendations can be applied to any vehicle type.
CURRENT
2017-03-02
Standard
AS6858
This is a joint SAE/EUROCAE development. This document will be released as both an SAE Aerospace Specification (AS) and a EUROCAE Minimum Aviation System Performance Standard (MASPS). This document defines the technical requirements for the safe integration of gaseous hydrogen fueled Proton Exchange Membrane (PEM) Fuel Cell Systems (FCS) within the aircraft. Most of the technical concepts and approaches covered by this document represent current industry "best practice". Others require specific approval from the procuring activity before use. This requirement for approval is not intended to prohibit their use; but rather to ensure that the prime contractor has fully investigated their capability to perform reliably and to be sufficiently durable under the required conditions and that the prime contractor can present substantiating evidence for approval before the design is committed to.
CURRENT
2017-03-01
Standard
AMS6509A
This specification covers a premium aircraft-quality alloy steel in the form of bars 199 in2 (1284 cm2) and under in cross section, forgings, and forging stock.
CURRENT
2017-03-01
Standard
AMS5916B
This specification covers a corrosion and heat-resistant alloy in the form of sheet, strip, and plate 2.00 inch (50.8 mm) and under in thickness (see 8.4).
CURRENT
2017-02-27
Standard
AMS2451/14
This specification covers the requirements for brush plating of nickel-tungsten by electrodeposition.
HISTORICAL
2017-02-22
Standard
AMS4959F
This specification covers a titanium alloy in the form of cold drawn wire.
2017-02-22
WIP Standard
AS478P

This standard provides the following:

a. Definition of terms pertaining to marking.

b. Symbols for marking location.

c. Requirements and restrictions for permanent markings

d. Types of marking methods.

e. Rules for designating marking methods.

f. Table listing marking methods.

CURRENT
2017-02-21
Standard
AS6023
The scope of this document is to: Provide a requirements document for RFID Tag Manufacturers to produce active RFID tags for the Aerospace industry. Identify the minimum performance requirements for active RFID tags to be used on or in close proximity to aircraft. Specify the test requirements specific to active RFID tags for aircraft use, in addition to RTCA DO-160 compliance requirements separately called out in this document. Identify existing standards applicable to active RFID Tag. Provide a certification standard for RFID tags which will use permanently-affixed installation on aircraft and aircraft parts. Battery standards are separately captured and not included in this document.
Viewing 151 to 180 of 9893