Criteria

Text:
Topic:
Content:
Display:

Results

Viewing 91 to 120 of 10147
2017-09-23
WIP Standard
AMS6448M
This specification covers an aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.
2017-09-23
WIP Standard
AMS6544E
This specification covers a maraging steel in the form of rolled or forged plate.
2017-09-23
WIP Standard
AMS6498B
This specification covers a nitriding grade of premium aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock. These products have been used typically for nitrided parts requiring high minimum core hardness with a narrow range, reduced distortion and subject to stringent magnetic particle inspection standards, but usage is not limited to such applications.
2017-09-23
WIP Standard
AMS6290K
This specification covers an aircraft-quality, low-alloy steel in the form of bars, forgings, and forging stock. These products have been used typically for carburized parts which require low minimum core hardness and allow a wide hardness range in sections 0.375 in. (9.50 mm) and under in nominal thickness, but usage is not limited to such applications. The core may or may not be machinable after hardening.
2017-09-23
WIP Standard
AMS7006
AMS for 718 powder to be used primarily for production of additively manufactured components. The powder could also be used for non-AM applications.
2017-09-23
WIP Standard
AMS6348E
This specification covers an aircraft-quality, low-alloy steel in the form of bars. These bars have been used typically for parts, 0.50 inch (12.7 mm) and under in section thickness at time of heat treatment, requiring a through-hardening steel capable of developing hardness as high as 35 HRC when properly hardened and tempered and also parts of greater thickness but requiring proportionately lower hardness, but usage is not limited to such applications.
2017-09-23
WIP Standard
AMS6360N
This specification covers an aircraft-quality, low-alloy steel in the form of seamless tubing. This tubing has been typically used in thin wall-thickness sections where minimum tensile strength up to 160,000 psi (1103 MPa) is required and where parts may be welded during fabrication, but usage is not limited to such applications.
2017-09-23
WIP Standard
AMS2251J
This specification covers established inch/pound manufacturing tolerances applicable to low-alloy steel bars ordered to inch/pound dimensions. These tolerances apply to all conditions, unless otherwise noted. The term "exclusive " is used to apply only to the higher figure of the specified range.
2017-09-22
WIP Standard
AMS6946D
This specification covers a titanium alloy in the form of sheet, strip, and plate.
2017-09-22
WIP Standard
AMS6945C
This specification covers a titanium alloy in the form of sheet, strip, and plate. <p> These products have been used typically for parts requiring strength up to 750 °F (400 °C), but usage is not limited to such applications.
2017-09-22
WIP Standard
J987
This SAE Standard applies to mobile construction-type lifting cranes utilizing rope-supported, conventional and luffing type lattice boom crane structures.
CURRENT
2017-09-22
Standard
AMS6327L
This specification covers an aircraft-quality, low-alloy steel in the form of bars and forgings.
2017-09-22
WIP Standard
AMS4967M
This specification covers a titanium alloy in the form of bars, wire, forgings, flash welded rings up through 4.000 inches (101.60 mm) in diameter or least distance between parallel sides and stock of any size for forging, heading, or flash welded rings (See 8.6).
2017-09-22
WIP Standard
AMS4919J
This specification covers a titanium alloy in the form of sheet, strip, and plate 0.025 to 3.000 inches (0.64 to 76.20 mm), inclusive, in nominal thickness.
2017-09-22
WIP Standard
AMS4918P
This specification covers a titanium alloy in the form of sheet, strip, and plate up through 4.000 inches (101.60 mm), inclusive.
2017-09-22
WIP Standard
AMS4985F
This specification covers a titanium alloy in the form of investiment castings.
2017-09-22
WIP Standard
AMS4937E
This specification covers a titanium alloy in the form of extruded bars, tubes, and shapes, and of flash welded rings and stock for flash welded rings.
2017-09-22
WIP Standard
AMS4914G
This specification covers a titanium alloy in the form of sheet and strip up to and including 0.125 inches in thickness. These products have been used typically in applications requiring high strength-to-weight ratio and stability up to 550 °F (288 °C), but usage is not limited to such applications. Parts are typically formed in the solution heat treated condition and subsequently precipitation heat treated to final condition.
2017-09-22
WIP Standard
AMS4900Q
This specification covers one grade of commercially-pure titanium in the form of sheet, strip, and plate.
2017-09-22
WIP Standard
AMS4992C
This specification covers titanium Ti 6Al-4V alloy in the form of investment castings.
2017-09-22
WIP Standard
AMS4991F
This specification covers a titanium alloy in the form of investment castings having four grades of permissible discontinuities.
2017-09-22
WIP Standard
AMS4989D
This specification covers a titanium alloy in the form of sheet, strip, and plate.
2017-09-22
WIP Standard
AMSH81200E
This specification covers the heat treatment of titanium and titanium alloy mill products (raw material), including wrought and cast products, by material producers. This specification also covers furnace equipment requirements, test procedures, and general information for heat treating procedures, heat treating temperatures, and material test procedures for the heat treatment of titanium and titanium alloys. It also describes procedures that, when followed, have produced the desired properties within the limitations of the respective alloys.
CURRENT
2017-09-22
Standard
AMS2685F
This specification defines the requirements for joining metals and alloys using the gas-tungsten-arc welding (GTAW) methods.
2017-09-21
WIP Standard
AMSQQP416F
This specification covers the requirements for electrodeposited cadmium plating.
2017-09-20
WIP Standard
F17AA
These castings have been used typically for structural parts requiring strength up to 1350 °F (732 °C) and oxidation resistance up to 1800 °F (982 °C), but usage is not limited to such applications.
2017-09-20
WIP Standard
D17AC
This specification covers a copper-nickel-tin alloy in the form of back-extruded mechanical tube 1.100 to 13.6 inches (28 to 330 mm) in outer diameter. .
CURRENT
2017-09-20
Standard
AMS2510F
This specification covers the engineering requirements for finishing aircraft parts and assemblies with an engine gray enamel.
CURRENT
2017-09-20
Standard
AMS2550F
This specification covers the engineering requirements for a treatment to provide enhanced corrosion resistance to sheet metal parts, such as brackets, spacers, and washers, fabricated from martensitic Corrosion-resistant steels, usually AMS 5504 or AMS 5508 and having hardness not higher than 40 HRC, or ferritic corrosion-resistant steels, usually AMS 5506. The treatment is not recommended for use on parts subject to impact in service.
CURRENT
2017-09-20
Standard
AMSM45202B
This specification covers the requirements for equipment, materials and procedures to be used in anodic treatments for magnesium base alloys for the purpose of increasing their corrosion resistance or producing surfaces suitable for the application of a protective organic finish.
Viewing 91 to 120 of 10147