Criteria

Text:
Topic:
Content:
Display:

Results

Viewing 271 to 300 of 9986
2017-03-13
WIP Standard
ARP5316E
This SAE Aerospace Recommended Practice (ARP) addresses the general requirements for data recording procedures, packaging, and storing of elastomeric seals and seal assemblies which include an elastomeric element prior to the seal being assembled into hardware components. It applies specifically to those elastomeric seals and seal assemblies packaged shortly after manufacture. The storage period prior to installation of the elastomeric seals and seal assemblies into hardware components is commonly referred to as shelf life.

The information contained in this ARP is intended to be utilized by those organizations who do not have specific requirements or recommendations already in place for the control of elastomeric seals and seal assemblies. This ARP can be specified in control, storage, and procurement documents.

CURRENT
2017-03-08
Standard
AMS2418J
This specification covers the requirements for electrodeposited copper.
CURRENT
2017-03-07
Standard
AMS4473A
This specification covers an aluminum alloy in the form of plate 0.750 to 1.500 inch (19.05 to 38.10 mm), inclusive, in nominal thickness.
CURRENT
2017-03-03
Standard
AMS3025D
This specification covers two types of polyalkylene glycol in the form of a liquid.
2017-03-02
WIP Standard
ARP1962B
This document requires that the company (facility) employing the personnel ensure a verifiable program of on-the-job training, experience, education, classroom instruction, and evaluation of personnel using either company-created programs or programs described herein. It describes the requirements for training and approval of personnel performing certain heat-treating and associated operations. It also establishes that only approved personnel may perform or monitor the functions listed for the processes and materials listed.
2017-03-02
WIP Standard
AMS6532G
This specification covers a premium aircraft-quality alloy steel in the form of bars, forgings, and forging stock.
CURRENT
2017-03-02
Standard
AS6858
This is a joint SAE/EUROCAE development. This document will be released as both an SAE Aerospace Specification (AS) and a EUROCAE Minimum Aviation System Performance Standard (MASPS). This document defines the technical requirements for the safe integration of gaseous hydrogen fueled Proton Exchange Membrane (PEM) Fuel Cell Systems (FCS) within the aircraft. Most of the technical concepts and approaches covered by this document represent current industry "best practice". Others require specific approval from the procuring activity before use. This requirement for approval is not intended to prohibit their use; but rather to ensure that the prime contractor has fully investigated their capability to perform reliably and to be sufficiently durable under the required conditions and that the prime contractor can present substantiating evidence for approval before the design is committed to.
CURRENT
2017-03-02
Standard
J3108_201703
This recommended practice prescribes clear and consistent labeling methodology for communicating important xEV high voltage safety information. Examples of such information include identifying key high voltage system component locations and high voltage disabling points. These recommendations are based on current industry best practices identified by the responder community. Although this recommended practice is written for xEVs with high voltage systems, these recommendations can be applied to any vehicle type.
CURRENT
2017-03-01
Standard
AMS5916B
This specification covers a corrosion and heat-resistant alloy in the form of sheet, strip, and plate 2.00 inch (50.8 mm) and under in thickness (see 8.4).
CURRENT
2017-03-01
Standard
AMS6509A
This specification covers a premium aircraft-quality alloy steel in the form of bars 199 in2 (1284 cm2) and under in cross section, forgings, and forging stock.
CURRENT
2017-02-27
Standard
AMS2451/14
This specification covers the requirements for brush plating of nickel-tungsten by electrodeposition.
HISTORICAL
2017-02-22
Standard
AMS4959F
This specification covers a titanium alloy in the form of cold drawn wire.
2017-02-22
WIP Standard
AS478P

This standard provides the following:

a. Definition of terms pertaining to marking.

b. Symbols for marking location.

c. Requirements and restrictions for permanent markings

d. Types of marking methods.

e. Rules for designating marking methods.

f. Table listing marking methods.

CURRENT
2017-02-21
Standard
AS6023
The scope of this document is to: Provide a requirements document for RFID Tag Manufacturers to produce active RFID tags for the Aerospace industry. Identify the minimum performance requirements for active RFID tags to be used on or in close proximity to aircraft. Specify the test requirements specific to active RFID tags for aircraft use, in addition to RTCA DO-160 compliance requirements separately called out in this document. Identify existing standards applicable to active RFID Tag. Provide a certification standard for RFID tags which will use permanently-affixed installation on aircraft and aircraft parts. Battery standards are separately captured and not included in this document.
CURRENT
2017-02-17
Standard
AMSQQA225/4A
This specification covers the specific requirements for 2014 aluminum alloy bar, rod, wire and special shapes produced by rolling, drawing or cold finishing.
2017-02-16
WIP Standard
AMS4485A
This specification covers a magnesium alloy in the form of extruded bars, rods, wire, tubing, and profiles. These extrusions have been used typically for parts requiring a combination of light weight, high yield strength up to 480 °F (250 °C), relatively high corrosion resistance, and good flammability resistance for magnesium alloys,but usage is not limited to such applications.
2017-02-16
WIP Standard
AMS2745B
This specification defines the requirements for locally hardening steel parts by the induction hardening method.
CURRENT
2017-02-15
Standard
AMS5047G
This specification covers an aluminum-killed carbon steel in the form of sheet and strip.
CURRENT
2017-02-14
Standard
AMS4071N
This specification covers an aluminum alloy in the form of drawn, round seamless tubing having a wall thickness of 0.010 to 0.450 inch (0.25 to 11.43 mm) inclusive, and nominal outside diameters of 0.125 to 3.000 inch (3.18 to 76.2 mm), inclusive (see 8.5).
CURRENT
2017-02-13
Standard
AMS4472A
This specification covers an aluminum alloy in the form of plate 0.500 to 2.250 inch (12.70 to 57.15 mm) in nominal thickness (see 8.5).
CURRENT
2017-02-09
Standard
AMS2800E
This specification covers the requirements for identification of finished parts.
CURRENT
2017-02-09
Standard
J1701_201702
This SAE Information Report is provided as an advisory guide. Individual application discretion is recommended. The content has been presented as accurately as possible, but responsibility for its application lies with the user. The document covers the variables in the torque-tension relationship: friction, materials, temperature, humidity, fastener and mating part finishes, surfaces, and the kind of wrenching employed. Also, described in this document is the torque management required to achieve correct fastener joint tightening. The thread fit of fasteners must be in accordance with Class 2A for external and Class 2B for internal inch threads.
CURRENT
2017-02-01
Standard
AMS5647K
This specification covers a corrosion-resistant steel in the form of bars, wire, forgings, mechanical tubing, flash welded rings, and stock for forging or flash welded rings.
2017-02-01
WIP Standard
AMS2588A
This specification covers the equipment and process requirements for forming or straightening metal parts using Ultrasonically Activated Needle Peening.
2017-01-30
WIP Standard
GA AM17-A
To enable consistency across AM specifications the committee considers it necessary to establish definitions for common terms that will be used in applicable AM specifications.
CURRENT
2017-01-24
Standard
AIR5575A
This SAE Aerospace Information Report (AIR) discusses the often overlooked relationship between hot stamp marking and the environmental conditions that contribute aircraft wiring problems and discusses current beliefs of military service experts, regulatory agencies and industry standard writing bodies about the potential hazards imposed by the hot stamping process.
CURRENT
2017-01-19
Standard
AMS5639J
This specification covers a corrosion-resistant steel in the form of bars, wire, forgings, mechanical tubing, flash welded rings, and stock for forging or flash welded rings.
CURRENT
2017-01-18
Standard
AMS5618J
This specification covers a premium aircraft-quality corrosion-resistant steel in the form of bars, wire, forgings, and forging stock.
CURRENT
2017-01-18
Standard
AMS6431P
This specification covers a premium aircraft-quality, low-alloy steel in the form of bars, forgings, mechanical tubing, and forging stock.
CURRENT
2017-01-12
Standard
AMS3415E
This specification covers the requirements for an aluminum brazing flux in granular form.
Viewing 271 to 300 of 9986