Criteria

Text:
Content:
Display:

Results

Viewing 1 to 30 of 650
2017-10-12
WIP Standard
J1814
General criteria are presented as guidelines for: control device location, resistance, and actuation of hand and foot controls by the machine's operator. The criteria are based upon physical limitations as defined by human factors engineering principles. This SAE Recommended Practice applies to upright seated operators of Road Building and Maintenance, and Specialized Mining Machinery categories of off-road, self-propelled work machines as identified in SAE J1116. The criteria presented should apply to most situations. Each situation, however, must be evaluated as to its own function and its relationship to other functions to achieve the desired operation action in normal and emergency situations with high probability. The values for control displacement and resistance apply only to what is required to achieve the desired performance of the function being controlled for the 5th through the 95th percentile person as defined in ISO 3411.
CURRENT
2017-10-10
Standard
J444_201710
This SAE Recommended Practice pertains to blast cleaning and shot peening and provides for standard cast shot and grit size numbers. For shot, this number corresponds with the opening of the nominal test sieve, in ten thousandths of inches , preceded by an S. For grit, this number corresponds with the sieve designation of the nominal test sieve with the prefix G added. These sieves are in accordance with ASTM E 11. The accompanying shot and grit classifications and size designations were formulated by representatives of shot and grit suppliers, equipment manufacturers, and automotive users.
2017-09-22
WIP Standard
J987
This SAE Standard applies to mobile construction-type lifting cranes utilizing rope-supported, conventional and luffing type lattice boom crane structures.
2017-09-17
WIP Standard
J1257
This recommended practice applies to mobile construction type cranes with cantilevered, telescopic booms when used in lifting crane service.
2017-08-16
WIP Standard
J1028
This SAE Recommended Practice applies to stationary usage of mobile construction-type cranes, crawler or rubber-tire mounted, on outriggers or on tires, when used for lifting crane, clamshell, dragline, magnet, pile driver, or similar service.
2017-08-15
WIP Standard
J1093
This SAE Information Report applies to wire rope supported, latticed crane boom systems mounted on mobile construction type cranes for lift crane service. The purpose of this document is to establish criteria for the analytical evaluation of the basic structural competence of wire rope supported latticed crane boom systems. The criteria and procedures specified include the evaluation of elastic stability for the overall boom system and individual members of the system.
2017-08-15
WIP Standard
J999
This SAE Standard applies to cranes which are equipped to adjust the boom angle by hoisting and lowering means through rope reeving. The purpose of this standard is to define the function and to stipulate the requirements of an automatic device to prevent raising a variable angle boom above its highest specified angle.
CURRENT
2017-08-09
Standard
J442_201708
This SAE standard defines requirements for equipment and supplies to be used in measuring shot peening arc height and other surface enhancement processes. Guidelines for use of these items can be found in SAE J443 and SAE J2597.
2017-08-03
WIP Standard
J899
This SAE Standard provides seat dimensions and adjustments for the design of operator's seat.
2017-04-20
WIP Standard
J1362
SAE J1362 presents graphical symbols for use on operator controls and other displays on off-road work machines as defined in SAE J1116 plus mobile cranes but excluding agricultural tractors. Symbols for agricultural tractors are covered by ASABE S304, ISO 3767-1, and ISO 3767-2.
2016-12-07
WIP Standard
J983
This SAE Recommended Practice applies to mobile, construction type, crane and cable excavator hand and foot controls. It should not be construed to limit the use of, or to apply to combination controls, automatic controls, or any other special operating control requirements.
2016-09-27
WIP Standard
J717
This SAE Standard establishes specifications for mid- and side-power take-off drives that will be helpful in designing implements. Design of the implement attaching means must be tailored to each tractor, depending on attaching points available and the exact location of the auxiliary shaft.
2016-09-27
WIP Standard
J283
The lift capacity can be determined by Section 4 and/or Section 5. When the results are recorded, the test method shall be identified.
CURRENT
2016-06-16
Standard
EIA441
This standard is intended to serve as a guide in the coordination of system design to promote uniformity of the nomenclature and description of the operator devices.
CURRENT
2016-06-16
Standard
EIAAB3D
Scope is unavailable.
CURRENT
2016-06-16
Standard
RS274D
This standard is intended to serve as a guidein the coordination of system design, to minimize the variety of program manuscripts required, to promote uniformity of programming techniques, and to foster interchangeability of input data between numerically controlled machines of the same classification by type, process function, size, and accuracy. It is intended that simple numerically controlled machines be programmed usinga simple format, which is systematically expandable for morec omplex machines.
CURRENT
2016-05-31
Standard
EIA358C
The information and comments contained in this PREFACE should not be considered part of the Standard. They have been included for clarification and guidance purposes only. American National Standard Code for Information Interchange (ANSI X3.4) is designed to achieve coding uniformity for information interchange betweend ata processing and communication systems. The increasing use of computers and related equipment for preparation of perforated tape for numerical machine control and for conlmunication between various conlponents of advanced numerically controlled systems has demonstrated the need for standardized usage for numerical control. As a result, the EIA 1E-3 1 Committee,which is made up of representatives of control system builders, machine builders, and users,has prepared this Standard for use by people building and using numerical control equipment.
CURRENT
2016-05-31
Standard
EIA267C
This Standard defines a machine coordinate system and motion nomenclature for numerically controlled machines. It is intended to eliminate misunderstandings between manufacturers, programmers, and users of machine tools, to simplify programming, to facilitate the interchangeability of recorded data between machines of like configuration, and to simplify the training of programmers by the standardization of machine coordinate system and motion nomenclature. This Standard defines a machine coordinate system and machine movements so that a machine tool programmer can describe machining operations without having to know whether the tool approaches the workpiece or the workpiece approaches the tool. The rules contained in this Standard were developed with the cooperation of private industry and Government and are based on widely accepted industry practice and usage. They are also based, in part, on standards used in the international machine tool market.
2016-01-07
WIP Standard
ARP1247E
This SAE Aerospace Recommended Practice (ARP) outlines the basic general design requirements for ground support equipment used in the civil air transport industry. It is intended to assist the airlines in standardizing requirements for various configurations of equipment. For procurement of equipment, sections of this document should be specified with due consideration of the functional and environmental requirements of the equipment, and to the relative cost of satisfying those requirements.
2015-09-29
WIP Standard
J386
This standard provides performance and test requirements for operator restraint systems provided for off-road self-propelled work machines. This document applies to pelvic restraint systems (Type 1) for off-road, self-propelled work machines fitted with ROPS and commonly used in construction, earthmoving, forestry, and mining as referred to in SAE J1040 and industrial machines fitted with ROPS as referred to in SAE J1042.
2015-09-23
WIP Standard
J747
This SAE Standard applies to hydraulic directional control valves as applied to self-propelled work machines referenced in SAE J1116. It describes a laboratory test procedure for evaluating: a.) Flow versus pressure drop, b.) Leakage rate, c.) Operating effort, d.) Metering characteristics versus spool travel, pilot pressure, or electrical current, e.) Relief valve characteristics. This document applies to single and multiple section hydraulic directional control valves. This document illustrates axial, manually operated valves although the test procedure is applicable to other input forms such as rotary actuation, electric current, hydraulic or pneumatic pressure.
CURRENT
2015-07-01
Standard
EIA484A
The increasing use of computers and related equipment in Direct Numericai Control (DNCI) Systems for storage and distribution of machine programs to numerically controlled machines and for communication between various components of DNC systems has demonstrated the need for a standard data communication link between the DNC and the numerical control unit. As a result, the EIA Committee IE-31 which is made up of representatives of numerical control system builders, machine builders and users has prepared this standard for use by people specifying, building and using DNC systems.
CURRENT
2015-07-01
Standard
EIA494B
The scope of this standard is the definition of the response of a numerically controlled machine to a valid sequence of records made up of 32 bit binary words or ASCII text strings. The standard defines the structure of these records and of the 32 bit binary words or ASCII text strings which make up the records. This standard addresses the control of machines capable of performing 2, 3, 4, and 5 axis motion of an active tool (mill, laser, pen, etc.) relative to a part, and those capable of 2 and 4 axis tool motion relative to a rotating part (turning machines), including parallel tool slide sets capable of concurrent (merged) motion.
CURRENT
2015-07-01
Standard
EIARS431
This standats covers both active amd passive aspects of the electrical interface between the Munerical Control (NC) and the machine power and logic contril, motor drive equipment, and other electrical apparatus on or associated with the machine tool.
2015-01-08
WIP Standard
J2267
This SAE standard applies to all forestry machines exposed to the hazard of objects penetrating the front of the operator station (other than the roof). This would include: Front guards for yarders with cabs mounted next to the tower; Front guards for forestry machines capable of handling material in front of and above the deflection limiting volume (DLV); such as knuckle boom log loaders and swing to tree feller bunchers; but excluding rubber-tired or tracked front-end loaders when equipped with buckets or forks with hold down grapple arm(s); and excluding forwarders and clambunk skidders fitted with load bunk headboards meeting the requirements of ISO 11850.
2014-12-05
WIP Standard
AIR1869D
This SAE Aerospace Information Report (AIR) covers information relative to ULDs (Unit Load Devices) container and pallet configurations, maximum usable container, pallet and bulk compartment volumes and tare weights for the lower deck of various wide-body aircraft. Bulk compartment volumes are also included for standard-body aircraft. This document brings together data concerning the lower deck capacity of wide-body and standard- body airplanes. The information includes airplanes manufactured by Airbus, Boeing, British Aerospace, British Aircraft, Fokker-VFW, Hawker Siddeley, Ilyushin, Lockheed and McDonnell- Douglas.
CURRENT
2014-10-21
Standard
J2417_201410
This SAE Standard provides a uniform method to calculate the lift capacity of knuckle-boom log loaders and certain forestry equipment. It establishes definitions and specifies machine conditions for calculations. This document applies to knuckle-boom log loaders as defined in ISO 6814 and ISO 17591 and certain forestry equipment defined in ISO 6814 that have a rotating upper-structure such as feller bunchers, forwarders, harvesters, and behind the cab or rear-mounted knuckle-boom log loaders not having their own power supply. It does not apply to harvesters that are incapable of lifting a tree or log completely off the ground. This document applies to those machines that are crawler, rubber-tired, and pedestal or stationary mounted.
Viewing 1 to 30 of 650

Filter

  • Standard
    650