Criteria

Text:
Content:
Display:

Results

Viewing 211 to 240 of 1154
CURRENT
2015-07-01
Standard
GEIAOP0001E
Scope is unavailable.
CURRENT
2015-07-01
Standard
EIA244
This standard for Numerical Machine Control Perforated Tape is intended to serve as a guide in the coordination of equipment design, to minimize the number of sizes and codes of perforated tape used, and to minimize the varity of perforated tape preparation equipment required by users of numerically controlled machines.
CURRENT
2015-07-01
Standard
EIA554A
This standard is intended to provide guidance for selecting standardized methods for estimating the proportion nonconforming expressed as PPM. These methods are contained in EIA 554-1, EIA 554-2 and EIA 591.
CURRENT
2015-07-01
Standard
SYSB1
The purpose of this EIA Bulletin is to provide a clearer, more definitive description of system engineering in order to promote greater recognition, more effective application, and the further development of this technical discipline that can be shared among systems contractors, subcontractors, engineering institutions, process tool developers and DoD.
CURRENT
2015-06-19
Standard
J200_201506
This classification system tabulates the properties of vulcanized rubber materials (natural rubber, reclaimed rubber, synthetic rubbers, alone or in combination) that are intended for, but not limited to, use in rubber products for automotive applications.
2015-05-26
WIP Standard
J656
This SAE Recommended Practice identifies and defines terms specifically related to brake systems.
CURRENT
2015-05-19
Standard
AS9132B
This standard defines uniform quality and technical requirements relative to metallic parts marking performed using "data matrix symbology" within the aviation, space, and defense industry. ISO/IEC 16022 specifies general requirements (e.g., data character encodation, error correction rules, decoding algorithm). In addition to ISO/IEC 16022 specification, part identification with such symbology is subject to the requirements in this standard to ensure electronic reading of the symbol. The marking processes covered by this standard are as follows: Dot Peening Laser Electro-Chemical Etching Further marking processes will be included, if required. Unless specified otherwise in the contractual business relationship, the company responsible for the design of the part shall determine the location of the data matrix marking. Symbol position should allow optimum illumination from all sides for readability. This standard does not specify information to be encoded.
CURRENT
2015-05-07
Standard
J2980_201505
This SAE Recommended Practice presents a method and example results for determining the Automotive Safety Integrity Level (ASIL) for automotive electrical and electronic (E/E) systems. This activity is required by ISO 26262-3:2011 [1], and it is intended that the process and results herein are consistent with ISO 26262:2011 [1]. The technical focus of this document is on vehicle motion control systems. It is limited to passenger cars weighing up to 3.5 metric tons. Furthermore, the scope of this recommended practice is limited to collision-related hazards. ISO 26262:2011 [1] has a wider scope than SAE J2980, covering other functions and accidents (not just motion control or collisions as in SAE J2980).
HISTORICAL
2015-05-01
Standard
TS200AR-42
No scope available.
CURRENT
2015-04-21
Standard
ARP9034A
This document describes requirements for standardized processes (and associated technologies) that ensure type design data are retrievable and usable for the life of a type certificate (50+ years). These processes are primarily concerned with, but not limited to, digital type design data retained in three-dimensional representations and associated data that is required for complete product definition, such as tolerances, specification call-outs, product structure and configuration control data, etc. This process standard includes process requirements for managing the evolution of technologies required to ensure the availability of the data for the life of the product. This data must be available to meet regulatory, legal, contractual and business requirements. This process standard is not intended to incorporate every company specific requirement and does not dictate specific organizational structures within a company.
2015-04-19
WIP Standard
J1115
Historically SAE has been concerned with nomenclature as an integral part of the standards development process. Guidelines for automotive nomenclature were written in 1916, were last revised in 1941, and were included in the SAE Handbook until 1962. The present diversity of groups working on nomenclature in the various ground vehicle committees led to the organization of the Nomenclature Advisory Committee under SAE Automotive Council.
2015-04-14
WIP Standard
AS6509
Fibre Channel is the primary avionics bus on many modern military aircraft. It is also the defined High-Speed bus for MIL-STD-1760E weapons applications. Profiled Ethernet networks are the primary avionics bus in many commercial aircraft and Commercial Ethernet is an ever increasing presence in modern military aircraft as well. This network standard is a convergence of Fibre Channel and Ethernet into a unified network standard which will provide a seamless approach to integrating end systems from either technology into a merged network structure. This work is based upon the commercial data storage market industry’s work on the Converged Data Storage Network or FCoE (Fibre Channel over Ethernet). This effort will look at profiling the FCoE work done in the commercial industry and adding information where necessary to affect a networking standard that will seamlessly integrate end systems from Commercial Ethernet, Fibre Channel, or FCoE enhanced devices.
2015-04-13
WIP Standard
AS5726B
This standard only defines interconnect, electrical and logical (functional) requirements for the interface between a Micro Munition and the Host. The physical and mechanical interface between the Micro Munition and Host is undefined. Individual programs will define the relevant requirements for physical and mechanical interfaces in the Interface Control Document (ICD) or system specifications. It is acknowledged that this does not guarantee full interoperability of Interface for Micro Munitions (IMM) interfaces until further standardization is achieved.
CURRENT
2015-04-09
Standard
J1538_201504
The terms included in the Glossary are general in nature and may not apply to all manufacturers’ systems. All terms in Section 3 apply to automotive inflatable restraint systems in general which are initiated by an electric or mechanical stimulus upon receipt of a signal from a sensor. These terms are intended to reflect existing designs and the Glossary will be updated as information on other types of systems becomes available. Appendix A is included to identify terminology that is no longer in common use or specifically applicable to inflatable restraint systems, but was published in the December 2001 version of SAE J1538.
2015-04-06
WIP Standard
AS6081A
This SAE Aerospace Standard standardizes practices to: a. identify reliable sources to procure parts, b. assess and mitigate risk of distributing fraudulent/counterfeit parts, c. control suspect or confirmed fraudulent/counterfeit parts, d. and report suspect and confirmed fraudulent/counterfeit parts to other potential users and Authority Having Jurisdiction.
CURRENT
2015-03-27
Standard
J2130/1_201503
This SAE Standard applies to all self-propelled machines with a gross vehicle mass greater than 5000 kg that are utilized to clean material from highways, parking lots, airfield runways, outside paved areas that are principally exposed to vehicular traffic. These machines can also be involved with road construction or repaving work. Primary methods for material removal and cleaning can be by mechanical, pneumatic, washing and flushing systems, or in a combination of any system.
CURRENT
2015-03-27
Standard
J2129_201503
This SAE Information Report lists the method which outside sources will follow when submitting documents for origination or review by the SAE CONAG Council.
CURRENT
2015-03-27
Standard
J1254_201503
This SAE Standard includes names of major components and parts peculiar to this type of machine. Illustrations used here are not intended to include all existing commercial machines or be exactly descriptive of any particular machine. They have been provided to describe the principles to be used in applying this document.
2015-03-24
WIP Standard
J3092
The purpose of this document is to provide information and guidelines for use by automotive designers, test engineers and policymakers with…
CURRENT
2015-03-12
Standard
AS9016A
The aviation, space, and defense industries rely on the development and manufacture of complex products comprised of multiple systems, subsystems, and components each designed by individual designers (design activities) at various levels within the supply chain. Each design activity controls various aspects of the configuration and specifications related to the product. When a change to design information is requested or required, the change has to be evaluated against the impacts to the higher-level system. Proposed changes to design information that the design activity identifies to be minor and have no effect on their product requirements or specifications have the potential to be concurrently implemented and approved, where authorized to do so. Changes that affect customer mandated requirements or specifications must be approved prior to implementation.
CURRENT
2015-02-26
Standard
J1272_201502
This SAE Standard is intended to describe the basic types of felling heads, including those with bunching capabilities, that are attachments to a self-propelled machine. Only the major components that are necessary to describe the functions of the felling head, and to apply the principles of the standard are included. Illustrations used are not intended to include all existing felling heads or to describe any particular manufacturer’s variation.
HISTORICAL
2015-02-18
Standard
J1939/84_201502
The purpose of this Recommended Practice is to verify that vehicles and/or components are capable of communicating a required set of information, in accordance with the diagnostic messages specified in SAE J1939-73, to fulfill the off-board diagnostic tool interface requirements contained in the government regulations cited below. This document describes the tests, methods, and results for verifying diagnostic communications from an off board diagnostic tool (i.e., scan tool) to a vehicle and/or component. SAE members have generated this document to serve as a guide for testing vehicles for compliance with ARB and other requirements for emissions-related on-board diagnostic (OBD) functions for heavy duty engines used in medium and heavy duty vehicles. The development of HD OBD regulations by US EPA and California’s Air Resources Board (ARB) require that diagnostic message services are exercised to evaluate diagnostic communication standardization requirements on production vehicles.
CURRENT
2015-02-05
Standard
AS13003
This standard defines the minimum requirements for conducting Measurement Systems Analysis (MSA) for variable and attribute assessment on characteristics as defined on the drawing or specification. It does not define the detailed analytical methods for each type of study as these can be found in existing published texts (see Section 2 for guidance).
CURRENT
2015-02-02
Standard
AS13001
The standard applies to aero engine suppliers operating a self-release process as a delegated activity from the delegating organization. While primarily developed around the aero engine supply chain requirements, this standard can also be used in other industry sectors where a self-release process may be of benefit.
CURRENT
2015-01-20
Standard
J300_201501
This SAE Standard defines the limits for a classification of engine lubricating oils in rheological terms only. Other oil characteristics are not considered or included.
CURRENT
2015-01-15
Standard
AS6502
This SAE Aerospace Standard (AS) provides classical propulsion system performance parameter names for aircraft propulsion systems and their derivatives, and describes the logical framework by which new names can be constructed.
HISTORICAL
2015-01-09
Standard
AS4877D
This procurement specification covers bolts and screws made from a corrosion and heat resistant, age hardenable nickel base alloy of the type identified under the Unified Numbering System as UNS N07718.
CURRENT
2014-12-18
Standard
ARP210A
"Hot Day ", "Tropical Day ", "Standard Day ", "Polar Day " and "Cold Day " are part of the lexicon of the aircraft industry. These terms are generally understood to refer to specific, generally accepted characteristics of atmospheric temperature versus pressure altitude. There are also other, less well-known days, defined by their frequency of occurrence, such as "1% Hot Day ", "10% Cold Day ", or "Highest Recorded Day ". These temperature characteristics have their origins in multiple sources, including U.S. military specifications which are no longer in force.
CURRENT
2014-12-05
Standard
AIR5444A
This SAE Aerospace Information Report (AIR) shall be limited to general information about tin whisker formation on tin plated conductors. It summarizes the mechanisms of metal whisker formation and describes possible conclusions as related to tin plated conductors. It also provides a number of reference documents that describes research and observations of the whisker phenomena, recommendations to prevent its formation and conclusions. The investigation by this task group of AE-8D was initiated by a request of the Naval Air Warfare Center, Indianapolis, Indiana, to determine if the phenomenon of tin whiskers is a problem in aerospace wire and cable.
Viewing 211 to 240 of 1154