Criteria

Text:
Content:
Display:

Results

Viewing 1201 to 1230 of 1276
HISTORICAL
1977-09-01
Standard
J1044A_197709
This SAE Recommended Practice establishes procedure for the issuance and assignment of a World Manufacturer Identifier (WMI) on a uniform basis to vehicle manufacturers who may desire to incorporate it in their Vehicle Identification Numbers (VIN). This recommended practice is intended to be used in conjunction with the recommendations for VIN systems described in SAE J853a, J187, J272b, J273a, J1108, and other SAE reports for VIN systems. These procedures were developed to assist in identifying the vehicle as to its point of origin. It was felt that issuance of the WMI by a single organization would avoid duplication of manufacturer identifiers and assist in the identification of vehicles by agencies such as those concerned with motor vehicle titling and registration, law enforcement, and theft recovery.
HISTORICAL
1977-06-01
Standard
J1071_197706
This SAE Standard covers the relative position and direction of motion of controls which influence the movement of the machine and the operating direction only of equipment controls. There is no intention to eliminate or restrict the use of combination controls, automatic controls, or special operating controls. Purpose This document is intended as a guide for designing uniform operator controls for graders. Graders are defined in SAE J/ISO 6165.
HISTORICAL
1977-06-01
Standard
J1092_197706
This SAE Standard provides names of major components peculiar to tractors (wheel) as referred to in SAE J1116 under Section 2: SELF-PROPELLED GENERAL PURPOSE INDUSTRIAL MACHINES. Illustrations are shown in Figure 1. Illustrations of components are not intended to be exactly descriptive of any particular machine.
HISTORICAL
1977-06-01
Standard
J727B_197706
This Standard provides provides names of major components peculiar to crawler tractors as defined in SAE J1057a (June, 1975). Illustrations of components are not intended to be exactly descriptive of any particular machine.
HISTORICAL
1977-06-01
Standard
J729A_197706
This standard provides the names of major components of dozers which include a blade and all associated structural elements, normally mounted in front of a self-propelled machine for scraping and pushing materials through forward motion of the machine. It also includes dimensional specification definitions applicable to dozers. This standard is applicable to dozers which are commonly used on crawler and wheel tractors as defined in SAE J1057.
HISTORICAL
1977-06-01
Standard
J950_197706
Not available.
HISTORICAL
1977-06-01
Standard
J1014_197706
This SAE Standard includes only those towing winches commonly used on skidders and crawler tractors. These winches are used on self-propelled machines described in SAE J1057; J1116; and J1209. Specifically excluded are those winches used for hoisting operations. This document classifies the major types of winch and establishes nomenclature for major winch components. Examples used here are not intended to include all existing winches nor to be descriptive of any particular winch.
HISTORICAL
1977-06-01
Standard
J386A_197706
This standard provides performance and test requirements for operator restraint systems provided for off-road self-propelled work machines. This document applies to pelvic restraint systems (Type 1) for off-road, self-propelled work machines fitted with ROPS and commonly used in construction, earthmoving, forestry, and mining as referred to in SAE J1040 and industrial machines fitted with ROPS as referred to in SAE J1042.
HISTORICAL
1977-05-01
Standard
J33A_197705
This SAE Recommended Practice sets forth accepted definitions and terminology of major components and parts peculiar to snowmobiles. Illustrations have been selected to identify functional characteristics and to identify common mechanisms. They are not intended to show all existing commercial machines or to be exactly descriptive of any particular machine. These criteria were prepared to facilitate clear understanding and promote uniformity in snowmobile nomenclature.
HISTORICAL
1977-03-01
Standard
J415J_197703
(These definitions were prepared by the Joint Committee on Definitions of Terms Relating to Heat Treatment appointed by the American Society for Testing and Materials, The American Society for Metals, the American Foundrymen's Association, and the SAE.) This SAE revision emphasizes the terms used in heat treating ferrous alloys, but also includes for reference some non-ferrous definitions at the end of the document. This glossary is not intended to be a specification, and it should not be interpreted as such. Since this is intended to be strictly a set of definitions, temperatures have been omitted purposely.
HISTORICAL
1977-02-01
Standard
J273A_197702
This SAE Recommended Practice provides direction for the design of a passenger car Vehicle Identification Number (VIN). This practice supplements SAE J272c. It applies to characteristics of passenger car descriptive and identifying information which are to be set forth in a uniform manner in the vehicle identification number.
HISTORICAL
1977-02-01
Standard
J1044A_197702
This SAE Recommended Practice establishes procedure for the issuance and assignment of a World Manufacturer Identifier (WMI) on a uniform basis to vehicle manufacturers who may desire to incorporate it in their Vehicle Identification Numbers (VIN). This recommended practice is intended to be used in conjunction with the recommendations for VIN systems described in SAE J853a, J187, J272b, J273a, J1108, and other SAE reports for VIN systems. These procedures were developed to assist in identifying the vehicle as to its point of origin. It was felt that issuance of the WMI by a single organization would avoid duplication of manufacturer identifiers and assist in the identification of vehicles by agencies such as those concerned with motor vehicle titling and registration, law enforcement, and theft recovery.
HISTORICAL
1977-01-01
Standard
J751D_197701
To establish a standard nomenclature for tire classifications and tire and rim components. This Recommended Practice describes the classification of off-road tires and rims for use on construction machines, defines related terminology in common use, and shows representative construction details of component parts.
HISTORICAL
1976-12-01
Standard
J1150_197612
This SAE Standard specifies terminology for agricultural equipment designed primarily for use in agricultural operations fo rthe production of food and fiber.
HISTORICAL
1976-11-01
Standard
J111B_197611
The purpose of this SAE Recommended Practice is to provide a glossary of radial seal terms and nomenclature which are normally encountered in the design, manufacture, installation, testing, inspection, and failure mode analysis of radial seals. The information will aid in the understanding and communication among those people associated with radial seals.
HISTORICAL
1976-10-01
Standard
J1163_197610
This SAE standard specifies a method and the device for use in determining the position of the Seat Index Point (SIP) for any kind of seat. This SAE document provides a uniform method for defining the location of the SIP in relation to some fixing point on the seat.
HISTORICAL
1976-08-01
Standard
J1145_197608
This SAE Recommended Practice applies to nomenclature of emissions and emissions reduction apparatus as applied to various engines and vehicles. Modifying adjectives are omitted in some cases for the sake of simplicity. However, it is considered good practice to use such adjectives when they add to clarity and understanding. This document was prepared to standardize terminology and nomenclature in order to facilitate clearer understanding for engineering discussions, comparisons, and the preparation of technical papers.
HISTORICAL
1976-07-01
Standard
J1142_197607
This SAE Recommended Practice describes the type of equipment commonly used with towing equipment, provides information to calculate safe steering loads, and outlines design criteria.
HISTORICAL
1976-07-01
Standard
J670_197607
Encompasses terminology related to directional control of vehicles. Revisions have also been made to update the original terminology. The function of uniform terminology is to promote understandable and exact communication. A great deal of effort has been expended to make these definitions suit this purpose. It is recognized that this terminology, like other dictionaries, must be revised periodically to reflect current usage and changing needs.
HISTORICAL
1976-07-01
Standard
J670E_197607
The vehicle dynamics terminology presented herein pertains to passenger cars and light trucks with two axles and to those vehicles pulling single-axle trailers. The terminology presents symbols and definitions covering the following subjects: axis systems, vehicle bodies, suspension and steering systems, brakes, tires and wheels, operating states and modes, control and disturbance inputs, vehicle responses, and vehicle characterizing descriptors. The scope does not include terms relating to the human perception of vehicle response.
HISTORICAL
1976-06-01
Standard
J1148_197606
This SAE Recommended Practice is intended to outline basic nomenclature and terminology in common use for engine charge air coolers, related charge air cooling system components, and charge air operating and performance parameters. An engine charge air cooler is a heat exchanger used to cool the charge air of an internal combustion engine after it has been compressed by an exhaust gas driven turbocharger, an engine driven turbocharger, or a mechanically or electrically driven blower. The use of a charge air cooler allows increased engine horsepower output, and may reduce emission levels and improve fuel economy through a more complete combustion due to the increased air density available. Typical cooling media includes the engine's coolant, ambient air, or an external water or coolant source.
HISTORICAL
1976-06-01
Standard
J1124_197606
Over the years during which fluid filtration systems have been developing, many terms have come into use for descriptions of characteristics of filter media, filter assemblies, test methods, and test materials. Inevitably, some terms have been applied loosely, so that the same term may have different meaning to different people, or in different frames of reference. Recognizing the need for clearly defined terms, which can have only one meaning for all persons in all circumstances, so that documents dealing with standard methods of evaluation of filters will have only one interpretation, the Filter Test Methods Subcommittee of the SAE Engine Committee has compiled this Glossary of related terms. No attempt has been made to produce an all-inclusive document, containing definitions of all terms related to all types of fluid filters. Instead, the Glossary is confined to the terms likely to be encountered in relation to filters for lubricating oil and fuels.
HISTORICAL
1976-04-01
Standard
J415H_197604
(These definitions were prepared by the Joint Committee on Definitions of Terms Relating to Heat Treatment appointed by the American Society for Testing and Materials, The American Society for Metals, the American Foundrymen's Association, and the SAE.) This SAE revision emphasizes the terms used in heat treating ferrous alloys, but also includes for reference some non-ferrous definitions at the end of the document. This glossary is not intended to be a specification, and it should not be interpreted as such. Since this is intended to be strictly a set of definitions, temperatures have been omitted purposely.
HISTORICAL
1975-11-01
Standard
J1121_197511
This recommended practice has been developed to assist engineers and designers in the preparation of specifications for the major types of helical compression and extension springs. It is restricted to a concise presentation of items which will promote an adequate understanding between spring manufacturer and spring user of the major practical requirements in the finished spring. Closer tolerances are obtainable where greater accuracy is required and the increased cost is justified. For the basic concepts underlying the spring design and for many of the details see the SAE Information Report MANUAL ON DESIGN AND APPLICATION OF HELICAL AND SPIRAL SPRINGS, SAE HS 795, which is available from SAE Headquarters in Warrendale, PA 15096. A uniform method for specifying design information is shown in the TYPICAL DESIGN CHECK LISTS FOR HELICAL SPRINGS, SAE J1122.
HISTORICAL
1975-08-01
Standard
J134B_197508
This SAE Recommended Practice establishes a uniform procedure for the level road test of the brake systems of all combinations of new multipurpose passenger vehicles, new light-duty trucks up to and including 4500 kg (10 000 lb), and new passenger cars when coupled with new trailers (braked or unbraked).
HISTORICAL
1975-08-01
Standard
J869A_197508
This SAE Standard provides names of major components peculiar to tractors used with scrapers and dumpers. (See Figures 1 to 3.) Reference SAE J1057. Illustrations of components are not intended to be exactly descriptive of any particular machine.
HISTORICAL
1975-08-01
Standard
J415F_197508
(These definitions were prepared by the Joint Committee on Definitions of Terms Relating to Heat Treatment appointed by the American Society for Testing and Materials, The American Society for Metals, the American Foundrymen's Association, and the SAE.) This SAE revision emphasizes the terms used in heat treating ferrous alloys, but also includes for reference some non-ferrous definitions at the end of the document. This glossary is not intended to be a specification, and it should not be interpreted as such. Since this is intended to be strictly a set of definitions, temperatures have been omitted purposely.
Viewing 1201 to 1230 of 1276