Criteria

Text:
Content:
Display:

Results

Viewing 1 to 30 of 186
2017-09-22
WIP Standard
J987
This SAE Standard applies to mobile construction-type lifting cranes utilizing rope-supported, conventional and luffing type lattice boom crane structures.
2017-08-16
WIP Standard
J1028
This SAE Recommended Practice applies to stationary usage of mobile construction-type cranes, crawler or rubber-tire mounted, on outriggers or on tires, when used for lifting crane, clamshell, dragline, magnet, pile driver, or similar service.
2017-08-15
WIP Standard
J1093
This SAE Information Report applies to wire rope supported, latticed crane boom systems mounted on mobile construction type cranes for lift crane service. The purpose of this document is to establish criteria for the analytical evaluation of the basic structural competence of wire rope supported latticed crane boom systems. The criteria and procedures specified include the evaluation of elastic stability for the overall boom system and individual members of the system.
2017-04-28
WIP Standard
J2892
This document establishes standard graphical symbols and color conventions for use in either still (static) or animated graphics used for communicating service information. This document’s purpose is to communicate conventions for using those symbols and colors to accurately and consistently communicate intended information via graphics-based documentation. These practices are intended for use in service procedures, assembly instructions, training materials, and similar applications when trying to minimize the amount of human natural language text used within the document. The still and animated graphical conventions referenced should support effective communication via paper and “traditional” electronic media. The conventions can also extend to documenting via additional electronic delivery paradigms such as Augmented Reality (AR).
CURRENT
2017-03-30
Standard
J2403DA_201703
This document is intended to supplement SAE J2403 by providing the content of Table 1, Table 2, and Table 3 from SAE J2403 in a form that can be sorted and searched for easier use. It is NOT intended as a substitute for the actual document, and any discrepancies between this Digital Annex and the published SAE J2403 document must be resolved in favor of the published document. This document provides the content of Table 1 and Table 2 published in SAE J2403 into the single table in the 'Term' tab, while the 'Recommended Term Definitions' tab provides the content of Table 3 in SAE J2403 and the 'Glossary' tab provides the content of Table 4 in SAE J2403.
CURRENT
2017-02-13
Standard
J2611_201702
This SAE information report covers the basic guidelines concerning off-road tire conditions that warrant replacement, removal, or repair. This material can assist the tire user in establishing specific written procedures for each job site.
CURRENT
2016-11-18
Standard
J2258_201611
This SAE Standard defines requirements relating to the elements of design, operation, and maintenance of light utility vehicles. The safety specifications in this document apply to any self-propelled, operator-controlled, off-highway vehicle 1829 mm (72 in) or less in overall width, exclusive of added accessories and attachments, operable on three or more wheels or tracks, primarily intended to transport material loads or people, with a gross vehicle weight of 2500 kg (5500 lb) or less, and a maximum design speed less than or equal to 40.23 km/h (25 mph). This document is not intended to cover Go-Karts (ASTM F2007-07a), Fun-Karts (ASTM F2011-02e1), Dune Buggies, and all terrain vehicles (ATVs) complying with ANSI/SVIA 1.
2016-03-29
WIP Standard
J1337
This SAE Information Report covers the important fundamental maintenance and service precautions for all off-road single-piece and multi-piece rims. Detailed information on specific procedures concerning mounting, demounting, maintenance and service of a particular type, style, or design of off-road rim assembly can be obtained by consulting rim or tire manufacturers or distributors. These procedures and service precautions are guidelines to be considered in preparation of the machine service manual and operator's manual and workplace procedures. It is the intent of this Information Report to allow for further development and review of these guidelines and then make this document a Recommended Practice.
HISTORICAL
2016-02-18
Standard
J2403DA_201602
This document is intended to supplement SAE J2403 by providing the content of Table 1, Table 2, and Table 3 from SAE J2403 in a form that can be sorted and searched for easier use. It is NOT intended as a substitute for the actual document, and any discrepancies between this Digital Annex and the published SAE J2403 document must be resolved in favor of the published document. This document provides the content of Table 1 and Table 2 published in SAE J2403 into the single table in the 'Term' tab, while the 'Recommended Term Definitions' tab provides the content of Table 3 in SAE J2403 and the 'Glossary' tab provides the content of Table 4 in SAE J2403.
CURRENT
2015-03-17
Standard
J2970_201503
This standard provides the testing and functional requirements guidance necessary for a leak detection device that uses any non-A/C refrigerant tracer gas, such as helium or a nitrogen-hydrogen blend, to provide functional performance equivalent to a refrigerant electronic leak detector. It explains how a non- refrigerant leak detector’s calibration can be established to provide levels of detection equal to electronic leak detectors that meet SAE J2791 for R-134a and SAE J2913 for R-1234yf.
HISTORICAL
2014-11-04
Standard
J2403DA_201411
This document is intended to supplement SAE J2403 by providing the content of Table 1, Table 2, and Table 3 from SAE J2403 in a form that can be sorted and searched for easier use. It is NOT intended as a substitute for the actual document, and any discrepancies between this Digital Annex and the published SAE J2403 document must be resolved in favor of the published document. This document provides the content of Table 1 and Table 2 published in SAE J2403 into the single table in the 'Term' tab, while the 'Recommended Term Definitions' tab provides the content of Table 3 in SAE J2403 and the 'Glossary' tab provides the content of Table 4 in SAE J2403.
CURRENT
2014-10-24
Standard
J67_201410
This SAE Standard applies to all machines with shovel, clam, or dragline attachment.
2014-08-18
WIP Standard
J98
This SAE Standard is intended to be used as a guide for manufacturers and users of general purpose industrial machines to provide a reasonable degree of protection for personnel during normal operation and servicing. This document excludes skid steers which are covered by SAE J1388. Avoidance of accidents also depends upon the care exercised by such persons (see SAE J153). Inclusion of this standard instate, federal, or any laws or regulations where flexibility of revision is lacking is discouraged.
CURRENT
2013-10-29
Standard
J920_201310
This Recommended Practice applies to technical publications which present instructions for the proper unloading, set-up, installations, pre-delivery inspection, operation, and servicing of off-road self-propelled work machines as categorized in SAE J1116. Advertising/marketing and other pre-purchase publications are not included.
CURRENT
2013-08-21
Standard
J1360_201308
This standard covers self-propelled off-road work machines as categorized in SAE J1116 and Agricultural Tractors as defined in ANSI/ASAE S390.
CURRENT
2013-07-16
Standard
J2425_201307
This SAE Recommended Practice describes a laboratory test procedure for evaluating the characteristics of heavy truck steering control systems under simulated driver impact conditions. The test procedure employs a torso-shaped body block that is impacted against the steering wheel.
2013-06-28
WIP Standard
J1332
The purpose of this recommended practice is to establish the minimum performance requirements for devices used to indicate to the crane operator by visual, audible, or tactile means the movement of a rope drum. This SAE Recommended Practice applies to cranes when used in lifting crane service which are equipped with rope drum rotation indicating devices.
CURRENT
2013-06-17
Standard
J1063_201306
This SAE Standard applies to mobile, construction-type lifting cranes of the cantilever boom type (Figure 1). Questions and comments regarding application or interpretation of the provisions in this test method should be referred to the originating SAE Committee.1
CURRENT
2013-03-28
Standard
J1289_201303
To establish conditions to be taken into consideration in determining rated loads for mobile cranes when overturning stability is the controlling factor. This recommended practice applies to mobile, construction-type lifting cranes with either lattice booms or cantilevered, telescopic booms.
CURRENT
2013-03-26
Standard
J2519_201303
These general guidelines and precautions apply to personnel operating directional drilling tracking equipment when used with Horizontal Earthboring Machines as defined in SAE J2022.
2013-03-19
WIP Standard
J1078
This analysis applies to crane types as covered by Power crane and shovel Association Standard Number Two, Mobile Hydraulic Crane standards and ANSI B30.15; refer to 5.1. This calculation method has been established to illustrate an analysis to determine the competence of hydraulic telescopic cantilevered crane booms.
CURRENT
2013-02-21
Standard
J1299_201302
This SAE Information Report applies to the control circuits and devices associated with the electrical propulsion system used on electric drive dumpers. Dumper is defined in J/ISO 6165. The document does not apply to auxiliary equipment control systems such as: Battery charging systems Engine wiring and control Monitoring and control circuits not directly affecting the operation of the electric propulsion and retarding system Lighting Accessory systems (heating, air conditioning, horns, radios, emergency steering, fire protection, and similar functions).
CURRENT
2013-02-21
Standard
J1908_201302
This SAE Standard outlines general procedures for the grounding of electrical components in 12- and 24-V systems, intended for light and heavy-duty on-highway trucks and their trailers; and off-road machinery applications as described in SAE J1116.
CURRENT
2013-01-18
Standard
J1811_201301
This SAE Standard is intended for light and heavy-duty on-highway trucks and their trailers; and off- road machinery applications as described in SAE J1116. The terminals described in this document are primarily used to connect batteries, cranking motors, solenoids, magnetic switches, and master disconnect switches and power cable assemblies.
CURRENT
2013-01-02
Standard
J818_201301
This SAE Standard establishes the definition of a normal all day rated operating load for loaders as defined in SAE J1057. This SAE Standard applies to wheel and crawler loaders taking only hydraulic lift capacity and tipping capacity into consideration. It is recognized that specific operating conditions may allow larger, or require smaller loads than the rated operating load. Some conditions could require more careful or restricted operation with the rated operating load. This standard is not to be construed as setting up test procedures or conditions.
CURRENT
2012-09-13
Standard
J1614_201209
This SAE Standard specifies requirements and design guidelines for electrical wiring systems of less than 50 V and cable diameters from 0.35 to 19 mm2 used on off-road, self-propelled earthmoving machines as defined in SAE J1116 and agricultural tractors as defined in ASAE S390.
CURRENT
2012-08-20
Standard
J987_201208
This SAE Standard applies to mobile construction-type lifting cranes utilizing rope-supported, conventional and luffing type lattice boom crane structures.
CURRENT
2012-06-28
Standard
J732_201206
This SAE standard provides uniform definitions of specification terms peculiar to loaders as defined in SAE J1057. The specifications must be qualified by stating the track shoe type, width or the tire type, size, ply, and specified inflation pressure; the model number or type of bucket disregarding teeth; and the type and amount of counterweight and/or ballast, if any, with which the machine is equipped. Paragraphs 4.1 and 4.16 are further defined by Figures 1 to 4. The figures are not intended to be exactly descriptive of any particular machine.
CURRENT
2012-06-04
Standard
J959_201206
This SAE Standard applies to all mobile, construction-type, lifting cranes as equipped for operation with hook, clamshell, magnet, and grapple attachments. It is not applicable to excavating and demolition attachments such as shovels, hoes, draglines, and wrecking balls. The purpose of this document is to set forth wire-rope strength factors that have been proved by design and operating practice to be consistent with safety, economy, space, weight, and other requirements peculiar to mobile, construction-type, lifting cranes.
CURRENT
2012-05-02
Standard
J376_201205
This SAE Recommended Practice applies to cranes equipped with load indicating devices used in lifting crane service.
Viewing 1 to 30 of 186