Criteria

Text:
Sector:
Content:
Display:

Results

Viewing 1 to 30 of 453
2017-05-12
Standard
J1939/73_201705
SAE J1939-73 Diagnostics Application Layer defines the SAE J1939 messages to accomplish diagnostic services and identifies the diagnostic connector to be used for the vehicle service tool interface. Diagnostic messages (DMs) provide the utility needed when the vehicle is being repaired. Diagnostic messages are also used during vehicle operation by the networked electronic control modules to allow them to report diagnostic information and self-compensate as appropriate, based on information received. Diagnostic messages include services such as periodically broadcasting active diagnostic trouble codes, identifying operator diagnostic lamp status, reading or clearing diagnostic trouble codes, reading or writing control module memory, providing a security function, stopping/starting message broadcasts, reporting diagnostic readiness, monitoring engine parametric data, etc.
2017-04-28
WIP Standard
J2892
This document establishes standard graphical symbols and color conventions for use in either still (static) or animated graphics used for communicating service information. This document’s purpose is to communicate conventions for using those symbols and colors to accurately and consistently communicate intended information via graphics-based documentation. These practices are intended for use in service procedures, assembly instructions, training materials, and similar applications when trying to minimize the amount of human natural language text used within the document. The still and animated graphical conventions referenced should support effective communication via paper and “traditional” electronic media. The conventions can also extend to documenting via additional electronic delivery paradigms such as Augmented Reality (AR).
2017-03-17
Standard
J3083_201703
This document should be used as guidance for non-handbook based reliability predictions conducted on automotive electronics products. It presents a method that utilizes warranty and field repair data to calculate the failure rates of individual electronic components and predict the reliability of the entire electronic system. It assumes that the user has access to a database containing field return data with classification of components, times to failure, and a total number of components operating in the field.
2017-03-13
Standard
J2995_201703
This recommended practice will specify a standard duty cycle and set of conditions for component-level durability testing. The "duty cycle" refers to a set of loading conditions (e.g. torque or pressure and cycling count), and the 'test conditions" refers to environmental conditions such as temperature, humidity, and part conditioning from prior exposure (e.g. heat aging).
2017-03-10
Standard
J2762_201703
This Standard provides an overview of results and requirements needed to remove refrigerant from a mobile air conditioning system for determining refrigerant emissions (leakage). This reclaim procedure for use on fleet vehicles in a field service environment should produce an accuracy and repeatability sufficient to determine refrigerant loss within 2 g.
2017-03-07
Standard
J1930DA_201703
This Digital Annex contains all of the information previously found within the SAE J1930 tables, including diagnostic terms applicable to electrical/electronic systems and related mechanical terms, definitions, abbreviations, and acronyms.
2017-03-07
Standard
J1930_201703
This SAE Recommended Practice supersedes SAE J1930 OCT2008, and is technically equivalent to ISO 15031-2. This document is applicable to all light-duty gasoline and diesel passenger vehicles and trucks, and to heavy-duty gasoline vehicles. Specific applications of this document include diagnostic, service and repair manuals, bulletins and updates, training manuals, repair databases, underhood emission labels, and emission certification applications. This document should be used in conjunction with SAE J1930DA Digital Annexes, which contains all of the information previously contained within the SAE J1930 tables. These documents focus on diagnostic terms applicable to electrical/electronic systems, and therefore also contains related mechanical terms, definitions, abbreviations, and acronyms.
2017-03-03
WIP Standard
J180
This SAE document describes alternator physical, performance and application requirements for heavy-duty electrical charging systems for off road work machines including those defined in SAE J1116. The purpose of this SAE document is to provide information on which to base machine and component design and to establish minimum requirements which will result in the most satisfactory operation of charging systems in construction, agricultural, and industrial machinery environments.
2017-02-13
Standard
J2611_201702
This SAE information report covers the basic guidelines concerning off-road tire conditions that warrant replacement, removal, or repair. This material can assist the tire user in establishing specific written procedures for each job site.
2016-12-13
Standard
J2012_201612
This document supersedes SAE J2012 DEC2007, and is technically equivalent to ISO 15031-6:2010 with the exceptions described in 1.2. This document is intended to define the standardized Diagnostic Trouble Codes (DTC) that On-Board Diagnostic (OBD) systems in vehicles are required to report when malfunctions are detected. SAE J2012 may also be used for decoding of enhanced diagnostic DTCs and specifies the ranges reserved for vehicle manufacturer specific usage. This document includes: Diagnostic Trouble Code format. A description of the standardized set of Diagnostic Trouble Codes and descriptions contained in SAE J2012DA. The two most significant bytes of a DTC may be decoded according to two different lists; DTC Format Identifier 0x00 and 0x04. A description of the standardized set of Diagnostic Trouble Codes subtypes known as Failure Types contained in SAE J2012-DA (applies only when three byte DTCs are used).
2016-12-13
Standard
J2012DA_201612
The J2012 Digital Annex of Diagnostic Trouble Code Definitions Spreadsheet provides DTC information in an excel format for use in your organization's work processes. The column headings include the same information as contained in the J2012 standard.

There is also a column heading denoting which DTC have been updated in the current version.

2016-12-07
WIP Standard
J983
This SAE Recommended Practice applies to mobile, construction type, crane and cable excavator hand and foot controls. It should not be construed to limit the use of, or to apply to combination controls, automatic controls, or any other special operating control requirements.
2016-12-02
Standard
J2911_201612
This SAE Standard provides manufacturers, testing facilities and providers of technician training with a procedure for certifying compliance with the applicable standard. Manufacturers or seller who advertise their products as Certified to an SAE J standard shall follow this procedure. Certification of a product is voluntary; however, this certification process is mandatory for those advertising meeting SAE Standard(s) requirements. Only certifying to this standard allows those claiming compliance to advertise that their product (unit), component, or service technician training meets all requirements of the applicable SAE standard. Certification of compliance to this and the appropriate standard and use of the SAE label on the product shall only be permitted after all the required information has been submitted to SAE International and it has been posted on the SAE web site.
2016-10-20
Standard
J2892DA_201610
This Digital Annex (DA) contains the current, full-PDF version of J2892, Graphic-Based Service Information, and all of the 130 referenced graphical symbols. Each of the symbols is presented in two file formats, Adobe Illustrator (vector art) and Portable Network Graphic (raster image), and can be used by purchasers according to the terms of the included license agreement.
2016-10-20
Standard
J2913_201610
This SAE Standard provides testing and functional requirements to meet specified minimum performance criteria for electronic probe-type leak detectors. The equipment specified here will identify smaller refrigerant leaks when servicing motor vehicle air conditioning systems, including those engineered with improved sealing and smaller refrigerant charges to address environmental concerns and increase system efficiency. This document does not address any safety issues concerning the equipment design or use beyond that of sampling a flammable refrigerant save those described in 3.1 and 3.2 of this document. All requirements of this standard shall be verified in SAE J2911.
2016-10-13
WIP Standard
J3005-2
SAE J3005-2 describes OBD interface security guidelines for J1979 communications and best practices for telematic devices connected with the SAE J1962 OBD vehicle connector.
2016-09-13
Standard
J1707_201609
This SAE Recommended Practice provides basic recommendations for dispensing and handling of SAE J1703 and SAE J1704 Brake Fluids by Service Maintenance Personnel to assure their safe and effective performance when installed in or added to motor vehicle hydraulic brake actuating systems. This document is concerned only with brake fluid and those system parts in contact with it. It describes general maintenance procedures that constitute good practice and that should be employed to help assure a properly functioning brake system. Recommendations that promote safety are emphasized. Specific step-by-step service instructions for brake maintenance on individual makes or models are neither intended nor implied. For these, one should consult the vehicle manufacturer’s service brake maintenance procedures for the particular vehicle. Vehicle manufacturer’s recommendations should always be followed.
2016-09-07
WIP Standard
J3005-1
SAE J3005-1 is being published as a new document which replaces J3005:20140602 ( Guidance for Remote I/M programs, Portable Emission Measurement Systems (PEMS), GPS, Wireless-LAN or Bluetooth interfaces and insurance devices.) The SAE J3005-1 devices are not intended to be used for SAE J1699-3 vehicle validation testing. The document focuses on OBD mandated communication protocols defined in SAE J1979.
2016-09-06
WIP Standard
J2819
This Technical Information Report defines the diagnostic communication protocol TP2.0. This document should be used in conjunction with SAE J2534-2 in order to fully implement the communication protocol in an SAE J2534 interface. Some Volkswagen of America and Audi of America vehicles are equipped with ECU(s), in which a TP2.0 proprietary diagnostic communication protocol is implemented. The purpose of this document is to specify the requirements necessary to implement the communication protocol in an SAE J2534 interface.
2016-09-06
WIP Standard
J2809
This Technical Information Report defines the proprietary diagnostic communication protocol for ABS or VSA ECU (Electronic Control Unit) implemented on some Honda vehicles. This protocol does not apply to all Honda vehicles. This document should be used in conjunction with SAE J2534-2 in order to fully implement the communication protocol in an enhanced SAE J2534 interface. The purpose of this document is to specify the requirements necessary to implement the communication protocol in an enhanced SAE J2534 interface.
2016-05-17
WIP Standard
J2901
The intent of the specification is to present a functional set of requirements which define the user and hardware interfaces while providing sufficient capability to meet the misfire patterns for compliance demonstration and engineering development. The misfire generator behaves as a spark-defeat device which induces misfires by inhibiting normal ignition coil discharge. It does so by monitoring the vehicle’s ignition timing signals and suspends ignition coil saturation for selected cylinder firing events. The misfire generator will thereby induce engine misfire in spark ignited gasoline internal combustion engines; including rotary engines. This requirement assumes that the user has a fundamental understanding of misfire diagnostics as well as ignition controls. This requirement is not intended to be an introductory misfire guideline or interpretation of regulatory requirements.
2016-03-11
Standard
J2810_201603
The purpose of this SAE Standard is to provide minimum performance and operating feature requirements for the recovery of HFC-134a (R-134a) refrigerant to be returned to a refrigerant reclamation facility that will process it to the appropriate AHRI 700 Standard or allow for on-site recycling of the recovered refrigerant to SAE J2788 specifications by using SAE J2788 or SAE J3030 -certified equipment. It is not acceptable that the refrigerant removed from a mobile air-conditioning (A/C) system with this equipment be directly returned to a mobile A/C system. An identifier certified to SAE J2912 is to be used to identify the contents of the system prior to recovery of the refrigerant.
2016-02-03
Standard
J1555_201602
This SAE Recommended Practice applies to all portions of the vehicle, but design efforts should focus on components and systems with the highest contribution to the overall average repair cost (see 3.7). The costs to be minimized include not only insurance premiums, but also out-of-pocket costs incurred by the owner. Damageability, repairability, serviceability and diagnostics are inter-related. Some repairability, serviceability and diagnostics operations may be required for collision or comprehensive loss-related causes only. Some operations may be for non-collision-related causes only (warranty, scheduled maintenance, non-scheduled maintenance, etc.). Some may be required for both causes. The scope of this document deals with only those operations that involve collision and comprehensive insurance loss repairs.
2016-01-22
Standard
J1939/73_201601
SAE J1939-73 Diagnostics Application Layer defines the SAE J1939 messages to accomplish diagnostic services and identifies the diagnostic connector to be used for the vehicle service tool interface. Diagnostic messages (DMs) provide the utility needed when the vehicle is being repaired. Diagnostic messages are also used during vehicle operation by the networked electronic control modules to allow them to report diagnostic information and self-compensate as appropriate, based on information received. Diagnostic messages include services such as periodically broadcasting active diagnostic trouble codes, identifying operator diagnostic lamp status, reading or clearing diagnostic trouble codes, reading or writing control module memory, providing a security function, stopping/starting message broadcasts, reporting diagnostic readiness, monitoring engine parametric data, etc.
2015-12-21
WIP Standard
ARP6898
The goal of this new document is to provide criteria for managing, auditing, and controlling the use of rotating balancing tooling and associated support tools. A variety of subjects will be addressed including serialization and marking requirements, critical inspection criteria, performance tracking through tooling compensation trend analysis, handling of gage standards (rotor simulators, master blades, dummy blades, etc.), recommendations for periodic and preventive maintenance intervals, test recommendations to evaluate rotating tooling performance, requirements for traceable measures (such as torques, runouts, eccentricity, etc.), repeatability characterization, and criteria for return to service.
2015-12-09
WIP Standard
AS6372
This standard shall apply to all commercial human suborbital spaceflights governed by the Commercial Space Launch Amendments Act of 2004.
2015-11-05
Standard
J1939/75_201511
SAE J1939-75 Generator Sets and Industrial Applications defines the set of data parameters (SPNs) and messages (PGNs) for information predominantly associated with monitoring and control generators and driven equipment in electric power generation and industrial applications. The data parameters (SPNs) and messages (PGNs) previously published within this document are now published in SAE J1939DA. Applications using the SAE J1939-75 document may need to reference SAE J1939DA for the SAE J1939 parameters and messages for monitoring and controlling the power units, e.g., engines and turbines, that power the generators and driven industrial equipment.
2015-10-12
WIP Standard
J1699/3
The main purpose of this Recommended Practice is to verify that vehicles are capable of communicating a minimum subset of information, in accordance with the diagnostic test services specified in SAE J1979: E/E Diagnostic Test Modes, or the equivalent document ISO 15031-5: Communication Between Vehicle and External Equipment for Emissions-Related Diagnostics – Part 5: Emissions-related diagnostic services. Any software meeting these specifications will utilize the vehicle interface that is defined in SAE J2534, Recommended Practice for Pass-Thru Vehicle Programming.
2015-09-17
WIP Standard
J3110
This SAE standard applies to any and all Flushing Methods intended for use to internally clean, decontaminate, and recondition components and sections of the refrigerant circuit within a vehicle air conditioning system. This standard provides testing and acceptance criteria for determining the minimum performance of a Flushing Method, intended for use in the servicing and repair process of vehicle air conditioning system. This standard will only specify the Flushing Method performance criteria. Specifications for air conditioning Flushing Fluids are outlined in SAE J3091.
2015-08-28
Standard
J2064_201508
The Scope of SAE J2064 covers coupled hose assemblies intended for containing and circulating lubricant, liquid and gaseous R134a and/or R-1234yf refrigerant in automotive air-conditioning systems. Historically, requirements for the hose used in coupled automotive refrigerant air conditioning assemblies was included in SAE J2064. SAE J2064 has been changed to establish the requirements for factory and field coupled hose assemblies. SAE J3062 has been issued to define requirements for the hose used in these assemblies into its own standard. SAE J2064 also provides the necessary values used in SAE J2727 Mobile Air Conditioning System Refrigerant Emission charts for R-134a and R-1234yf. The certified coupling of MAC hose assemblies is required in meeting certain regulatory requirements. A hose which has met the requirements of SAE J3062 and certified in J2911 must be used as part of the coupled assembly.
Viewing 1 to 30 of 453