Criteria

Text:
Content:
Display:

Results

Viewing 1 to 30 of 679
2017-10-15
WIP Standard
D17AD
1.1 Form This specification covers an aluminum-lithium alloy in the form of plate with a product thickness range of 0.500" to 6.500". 1.2 Application This plate has been used typically for parts where low density is needed in combination with a high level of mechanical properties and very good resistance to stress-corrosion cracking, but usage is not limited to such applications. Material is delivered in T34 temper and solution heat treated to obtain T82 temper by the end user.
2017-09-27
WIP Standard
AMS4002A
This specification covers an aluminum alloy in the form of seamless, drawn tubing .
2017-09-27
WIP Standard
AMS3025E
This specification covers two types of polyalkylene glycol in the form of a liquid.
2017-09-27
WIP Standard
AMS4124F
This specification covers an aluminum alloy in the form of rolled or cold finished bars, rods, and wire.
2017-09-20
WIP Standard
D17AC
This specification covers a copper-nickel-tin alloy in the form of back-extruded mechanical tube 1.100 to 13.6 inches (28 to 330 mm) in outer diameter. .
CURRENT
2017-09-20
Standard
AMSM45202B
This specification covers the requirements for equipment, materials and procedures to be used in anodic treatments for magnesium base alloys for the purpose of increasing their corrosion resistance or producing surfaces suitable for the application of a protective organic finish.
2017-09-15
WIP Standard
D17AA
This specification covers the specific requirements for 2017 aluminum alloy bar, rod and wire produced by rolling, drawing or cold finishing supplied in the annealed (O temper) condition (see 8.4). When specified, product shall be supplied in the “as fabricated” (F) temper.
CURRENT
2017-08-07
Standard
AMS4485A
This specification covers a magnesium alloy in the form of extruded bars, rods, wire, tubing, and profiles from 0.039 to 4.75 inches, incl. (12.71.0 to 120.7 mm., incl.) in nominal thickness (see 8.4).
2017-07-24
WIP Standard
AMSWWT700/5B
This specification covers the specific requirements for seamless tube drawn from aluminum alloy 5086.
2017-07-24
WIP Standard
AMSWWT700B
This specification covers the general requirements for aluminum and aluminum alloy tube; drawn, seamless (see 6.1.1). Specific requirements for these products in a particular alloy are covered by the applicable detail specification (see 6.3).
CURRENT
2017-06-28
Standard
AMS4375M
This specification covers a magnesium alloy in the form of sheet and plate from 0.016 to 3.000 inches (0.41 to 76.20 mm), inclusive, in thickness (see 8.4).
2017-06-23
WIP Standard
D17AB
This revises the Identification section of the General Agreement on Marking.
CURRENT
2017-06-21
Standard
AMS4443H
This specification covers a magnesium alloy in the form of sand castings.
CURRENT
2017-06-09
Standard
AMS4352J
This specification covers a magnesium alloy in the form of extruded bars, rods, wire, tubing, and profiles up to 40 in2 (258 cm2) in cross-sectional area (solids) and up to 8.5 inches (216 mm) OD by 1.188 inches (30.18 mm) wall thickness (tubing) (see 8.4).
CURRENT
2017-05-30
Standard
AMS4490K
This specification covers a magnesium alloy in the form of die castings.
2017-05-30
WIP Standard
AMS4478A
This specification covers an aluminum alloy in the form of Alclad sheet and plate supplied in the –T81/-T851 temper. These products have been used typically for high strength parts requiring higher yield strength than is afforded by naturally aged tempers of this alloy and maximum corrosion resistance and whose fabrication does not involve welding, but usage is not limited to such applications.
CURRENT
2017-05-25
Standard
AMS4425D
This specification covers a magnesium alloy in the form of sand castings.
CURRENT
2017-05-25
Standard
AMS4420P
This specification covers a magnesium alloy in the form of sand castings.
CURRENT
2017-05-22
Standard
AMS4302C
This specification covers an aluminum alloy in the form of sheet laminated with one or more layers of unidirectional aramid fiber/epoxy prepreg.
CURRENT
2017-05-19
Standard
AMS4444E
This specification covers a magnesium alloy in the form of sand castings.
CURRENT
2017-05-19
Standard
AMS2355M
This specification covers quality assurance sampling and testing procedures used to determine conformance to applicable specification requirements of wrought aluminum alloy and wrought magnesium alloy mill products (except forging stock), and includes quality assurance and testing procedures for rolled, forged, and flash welded rings (see 8.3). Requirements are specified in inch/pound units.
2017-05-10
WIP Standard
AMS4820F
This specification covers bearings of leaded copper cast on one or both faces of a steel backing.
2017-05-10
WIP Standard
AMS4800F
This specification covers bearings of a tin alloy cast on one or both faces of a steel or bronze backing.
2017-05-10
WIP Standard
AMS4827F
This specification covers bearings of a leaded bronze cast on one or both faces of a steel backing.
2017-05-10
WIP Standard
AMS4382E
This specification covers a magnesium alloy in the form of plate. This product has been used typically for low-density, low-strength parts requiring rigidity and a high degree of flatness, dimensional stability, and weldability, but usage is not limited to such applications.
2017-05-10
WIP Standard
AMS4376J
This specification covers a magnesium alloy in the form of plate.
2017-05-10
WIP Standard
AMS4377K
This specification covers a magnesium alloy in the form of sheet and plate.
2017-05-10
WIP Standard
AMS4597B
This specification covers a copper-nickel-tin alloy in the form of bars and rods.
2017-05-10
WIP Standard
AMS4446D
This Specification covers a magnesium alloy in the form of sand castings.
2017-05-10
WIP Standard
AMS4403A
This specification covers an aluminum alloy in the form of die forgings 12 inches (305 mm) and under in nominal thickness and of forging stock.
Viewing 1 to 30 of 679

Filter

  • Standard
    679