Criteria

Text:
Content:
Display:

Results

Viewing 1 to 30 of 35
CURRENT
2016-11-18
Standard
J485_201611
SAE J485 specifies the recommended nominal diameters and locations of holes in bolt or screw shanks, and nominal widths and depths of slots in nuts, for use with the recommended sizes of inch-series cotter pins, as shown in Table 1.
CURRENT
2015-12-02
Standard
AMS4355
This specification covers discontinuously reinforced aluminum alloy (DRA) metal matrix composites (MMC) made by mechanical alloying of the 2124A powder and SiC particulate, which is then consolidated by Hot Isostatic Pressing (HIP) into shapes less than 62 in2 (0.04 m2) cross-section (see 8.11).
CURRENT
2015-04-15
Standard
AIR5367
This SAE Aerospace Information Report (AIR) provides information related to machining of composite materials, components and structures. This document is intended to supplement the machining processes and guidelines provided in OEM repair manuals and structural repair manuals. It is not intended to supersede the approved data provided in OEM repair documents.
CURRENT
2015-03-12
Standard
AS6507
The results of this test are intended to be a useful indication of the resistance to distortion of bare or two-side Alclad, flat sheet aluminum used in chemical milling applications.
CURRENT
2015-01-05
Standard
AMSC81769A
This specification covers the requirements for surface metal removal of ferrous and non-ferrous metals by milling processes using controlled immersion of parts in chemical etching solutions.
CURRENT
2014-12-29
Standard
AS6072
CURRENT
2014-11-07
Standard
AMS4025M
This specification covers an aluminum alloy in the form of sheet and plate from 0.006 to 3.000 inches (0.15 to 76.20 mm) in thickness, inclusive(See 8.4).
CURRENT
2013-03-26
Standard
J2519_201303
These general guidelines and precautions apply to personnel operating directional drilling tracking equipment when used with Horizontal Earthboring Machines as defined in SAE J2022.
CURRENT
2013-02-13
Standard
J2583_201302
This SAE Standard applies to planning and mapping various types of information associated with directional boring/drilling machines. This type of planning and mapping information is typically used with horizontal earthboring machines as defined by SAE J2022.
CURRENT
2013-01-02
Standard
J2520_201301
This SAE Standard applies to directional drilling electronics and tracking equipment of the following types: Tracking Transmitter Tracking Receiver Telemetry Device Remote Display This type of tracking equipment is typically used with Horizontal Earthboring Machines as defined in SAE J2022.
HISTORICAL
2007-08-30
Standard
J2520_200708
This SAE Standard applies to directional drilling electronics and tracking equipment of the following types: a. Tracking Transmitter b. Tracking Receiver c. Telemetry Device d. Remote Display This type of tracking equipment is typically used with Horizontal Earthboring Machines as defined in SAE J2022. The purpose of this document is to define common terms and commercial specifications associated with tracking equipment used in the horizontal earthboring industry.
HISTORICAL
2007-08-30
Standard
J2583_200708
This SAE Standard applies to planning and mapping various types of information associated with directional boring/drilling machines. This type of planning and mapping information is typically used with horizontal earthboring machines as defined by SAE J2022. This is a compilation of terms and definitions commonly associated with the planning and mapping of underground pipe and utility installation by using horizontal earthboring machines.
HISTORICAL
2007-08-30
Standard
J2519_200708
These general guidelines and precautions apply to personnel operating directional drilling tracking equipment when used with Horizontal Earthboring Machines as defined in SAE J2022. The purpose of this document is to provide manufacturers with an established set of guidelines and precautions to improve the degree of personal safety for jobsite personnel and people in the area.
HISTORICAL
2002-07-03
Standard
J2520_200207
This SAE Standard applies to directional drilling electronics and tracking equipment of the following types: a. Tracking Transmitter b. Tracking Receiver c. Telemetry Device d. Remote Display This type of tracking equipment is typically used with Horizontal Earthboring Machines as defined in SAE J2022. The purpose of this document is to define common terms and commercial specifications associated with tracking equipment used in the horizontal earthboring industry.
HISTORICAL
2002-06-28
Standard
J2583_200206
This SAE Standard applies to planning and mapping various types of information associated with directional boring/drilling machines. This type of planning and mapping information is typically used with horizontal earthboring machines as defined by SAE J2022. This is a compilation of terms and definitions commonly associated with the planning and mapping of underground pipe and utility installation by using horizontal earthboring machines.
Viewing 1 to 30 of 35

Filter

  • Standard
    35

Subtopics