Criteria

Text:
Sector:
Content:
Display:

Results

Viewing 1 to 30 of 604
CURRENT
2017-04-17
Standard
J361_201704
This SAE Recommended Practice applies to parts and materials used in vehicle manufacture which are intended to be acceptable color matches to a specified standard. This document is intended for use with parts or materials which are opaque or nearly so. Materials covered by this document include topcoat paint finishes, interior soft trim, interior and exterior hard trim, and exterior film and flexible trim. This practice requires judgments by observers with a minimum of normal color vision and preferably superior as rated with the FM-100 Hue Test as specified in ASTM E1499, Guide for Selection, Evaluation, and Training of Observers.
2017-04-07
WIP Standard
J3140
This SAE standard applies to compressor lubricants intended for aftermarket use in the refrigerant circuit of vehicle air-conditioning systems. This standard does not grant the user to qualify a lubricant as OEM approved. This SAE Standard is not limited by refrigerant selection, however, only refrigerants identified in SAE 639 may apply for SAE J2911 submission and container labeling.
2017-04-07
WIP Standard
J3142
This Information Report contains a survey of the types of coolant control valves in use and describes how they are used in vehicle and machine thermal management systems.
CURRENT
2017-03-10
Standard
J2762_201703
This Standard provides an overview of results and requirements needed to remove refrigerant from a mobile air conditioning system for determining refrigerant emissions (leakage). This reclaim procedure for use on fleet vehicles in a field service environment should produce an accuracy and repeatability sufficient to determine refrigerant loss within 2 g.
CURRENT
2017-03-07
Standard
J3112_201703
This SAE Standard establishes the test conditions and reporting method for quantifying refrigerant circuit oil circulation rate (OCR) reduction effectiveness of mobile air conditioning compressors using R-134a and R-1234yf refrigerants that include oil separators and/or other design features for the purpose of reducing the OCR in the refrigerant circuit.
CURRENT
2017-02-21
Standard
J2773_201702
This Standard describes methods to understand the risks associated with vehicle mobile air conditioning [MAC] systems in all aspects of a vehicle’s lifecycle including design, production, assembly, operation and end of life. Information for input to the risk assessment is provided in the Appendices of this document. This information should not be considered to be complete, but only a reference of some of the data needed for a complete analysis of the risk associated with the use of refrigerants in MAC systems.
2017-02-08
WIP Standard
J3136
This document provides clarity in terminology and nomenclature for multiple temperature coolant circuits used in gasoline and light to heavy duty diesel engine cooling systems in on-highway and off-highway vehicles and machines and includes a survey of the various types of systems in use.
CURRENT
2017-02-02
Standard
J2581_201702
This SAE Information report defines the thermal transport properties important in the assessment of heat management capability of brake lining, shoe, disc and drum materials. The report discusses thermal diffusivity, specific heat capacity, thermal conductivity and thermal expansion. Measurement techniques for the appropriate ASTM standards are identified. The thermal transport properties discussed are material sample properties, not the properties of entire components such as pad assemblies.
CURRENT
2016-12-02
Standard
J2911_201612
This SAE Standard provides manufacturers, testing facilities and providers of technician training with a procedure for certifying compliance with the applicable standard. Manufacturers or seller who advertise their products as Certified to an SAE J standard shall follow this procedure. Certification of a product is voluntary; however, this certification process is mandatory for those advertising meeting SAE Standard(s) requirements. Only certifying to this standard allows those claiming compliance to advertise that their product (unit), component, or service technician training meets all requirements of the applicable SAE standard. Certification of compliance to this and the appropriate standard and use of the SAE label on the product shall only be permitted after all the required information has been submitted to SAE International and it has been posted on the SAE web site.
HISTORICAL
2016-11-18
Standard
J361_201611
This SAE Recommended Practice applies to parts and materials used in vehicle manufacture which are intended to be acceptable color matches to a specified standard. This document is intended for use with parts or materials which are opaque or nearly so. Materials covered by this document include topcoat paint finishes, interior soft trim, interior and exterior hard trim, and exterior film and flexible trim. This practice requires judgments by observers with a minimum of normal color vision and preferably superior as rated with the FM-100Hue Test as specified in ASTM E1499, Guide for Selection, Evaluation, and Training of Observers.
2016-11-15
WIP Standard
J902
This SAE Recommend Practice establishes for passenger cars, light trucks, and multipurpose vehicles with GVW of 4500 kg (10 000 lb) or less, as defined by EPA, and M1 category vehicles as defined by the European Commission: a. Minimum performance standards for defrosting and demisting systems. b. Test procedures that can be conducted on uniform test equipment by commercially available laboratory facilities.
2016-10-25
WIP Standard
J826/1
This document describes the CAD model data available from SAE for the HPM-1 three-dimensional H-point machine. The elements of the CAD model include the outer surfaces of the cushion and back pans, datum points and lines, and calibration references. The intended purpose for this information is to provide a CAD reference for design and benchmarking as well as a calibration reference for the physical HPM-1 audits. The content and format of the data files that are available are also described. The actual CAD model files are included with this product and are provided in the following formats: CATIA v4 (without parametrics), CATIA v5 (without parametrics), IGES, and STEP.
2016-10-24
WIP Standard
J3132
This SAE Standard specifies the minimum performance recommendation for spark plugs intended for use in various internal combustion engines including Automotive, Marine, Motorcycle and Utility engine applications. This standard is not intended to supply information for spark plugs used in aircraft applications of any type.
CURRENT
2016-10-20
Standard
J2913_201610
This SAE Standard provides testing and functional requirements to meet specified minimum performance criteria for electronic probe-type leak detectors. The equipment specified here will identify smaller refrigerant leaks when servicing motor vehicle air conditioning systems, including those engineered with improved sealing and smaller refrigerant charges to address environmental concerns and increase system efficiency. This document does not address any safety issues concerning the equipment design or use beyond that of sampling a flammable refrigerant save those described in 3.1 and 3.2 of this document. All requirements of this standard shall be verified in SAE J2911.
CURRENT
2016-10-13
Standard
J2892_201610
This document establishes standard graphical symbols and color conventions for use in either still (static) or animated graphics used for communicating service information. This document’s purpose is to communicate conventions for using those symbols and colors to accurately and consistently communicate intended information via graphics-based documentation. These practices are intended for use in service procedures, assembly instructions, training materials, and similar applications when trying to minimize the amount of human natural language text used within the document. The still and animated graphical conventions referenced should support effective communication via paper and “traditional” electronic media. The conventions can also extend to documenting via additional electronic delivery paradigms such as Augmented Reality (AR).
CURRENT
2016-10-13
Standard
J826/2_201610
This document describes the 2-D computer-aided design (CAD) template for the HPM-1 H-point machine or HPD available from SAE. The elements of the HPD include the curve shapes, datum points and lines, and calibration references. The intended purpose for this information is to provide a master CAD reference for design and benchmarking. The content and format of the data files that are available are also described. The actual CAD model files are included with this product and are provided in the following formats: CATIA v5 (without parametrics), IGES, and STEP.
2016-10-10
WIP Standard
J1342
The technique outlined in this SAE Recommended Practice was developed as part of an overall program for determining and evaluating fuel consumption of heavy-duty trucks and buses, but it is applicable to off highway vehicles as well. It is recommended that the specific operating conditions be carefully reviewed on the basis of actual installation data. Cooling requirements are affected by all heat exchangers that are cooled by the fan drive system. These may include radiators, condensers, charge air coolers, oil coolers, and others. Because of the variation in size, shape, configuration, and mountings available in cooling fans and fan drive systems, specific test devices have not been included. Using known power/speed relationships for a given fan, this procedure can be used to calculate the fan drive system’s power consumption for engine cooling systems using fixed ratio, viscous or speed modulating, and mechanical on/off fan drives including electronically activated fan drives.
2016-10-10
WIP Standard
J164
This SAE Standard was developed primarily for passenger car and truck application, but may be used in marine, industrial, and similar applications.
2016-10-10
WIP Standard
J1436
This SAE Information Report is applicable to all engine cooling systems used in heavy-duty vehicles, industrial applications, and automotive applications The purpose of this document is to list the requirements which are in general use for filling, deaeration, and drawdown of engine cooling systems for heavy-duty, industrial and automotive applications. Due to the differences in heavy duty and automotive cooling systems, they are dealt with in separate sections of this report. In the case of heavy duty, these procedures apply to both the main jacket water pump and separate circuit water pumps. The material presented in this document is for information purposes only, and does not constitute a SAE Standard.
2016-10-10
WIP Standard
J1393
This document supersedes SAE J819 - Engine Cooling System Field Test. The purpose of this SAE Recommended Practice is to establish a testing procedure to determine the performance capability of engine cooling systems, including charge air coolers, on heavy-duty vehicles with liquid-cooled internal combustion engines. The definition of heavy vehicles for this document includes, but is not limited to, on- and off-highway trucks, cranes, drill rigs, construction, forestry and agricultural machines. Vehicles equipped with side or rear-mounted radiators may require an alternate procedure of a towing dynamometer because of peculiar aerodynamics. Testing is generally conducted to determine compliance with cooling criteria established by the engine manufacturer or the end product user to meet a desired engine reliability goal.
CURRENT
2016-09-30
Standard
J2678_201609
This document provides the rationale used by the Navigation Function Accessibility Subcommittee (the Subcommittee) for the development and content of a SAE J2364 Recommended Practice: Navigation and Route Guidance Function Accessibility While Driving. It provides both the reasoning for the overall recommended practice as well as each of its elements.
2016-09-03
WIP Standard
J1390
Three levels of fan structural analysis are included in this practice: 1. Initial Structural Integrity 2. In-vehicle Testing 3. Durability Test Methods The Initial Structural Integrity section describes analytical and test methods used to predict potential resonance and, therefore, possible fatigue accumulation. The In-vehicle (or machine) section enumerates the general procedure used to conduct a fan strain gage test. Various considerations that may affect the outcome of strain gage data have been described for the user of this procedure to adapt/discard depending on the particular application. The Durability Test Methods section describes the detailed test procedures that may be used depending on type of fan, equipment availability, and end objective. Each of the previous levels builds upon information derived from the previous level. Engineering judgment is required as to the applicability of each level to a different vehicle environment or a new fan design.
CURRENT
2016-08-02
Standard
J1324_201608
This SAE Recommended Practice provides test methods for determining the characteristics of acoustical and thermal materials. Where applicable, methods of test developed by SAE and ASTM have been referenced.
CURRENT
2016-06-28
Standard
J2830_201606
This recommended practice describes a process for testing the comprehension of static (i.e., fixed or non-dynamic) symbols for all ground vehicles, for both OEM and aftermarket products. With advancing display technology, it is now possible to display dynamic symbols (e.g., a spinning beach ball to show that a process is ongoing, or a diagram showing energy distribution in hybrid vehicles). Such graphics are outside of the scope of this recommended practice, though extensions of this process may be useful for testing them. However, several symbols which occupy the same space on a display may change state without movement (e.g. play/pause button); these are within the scope of this recommended practice. The process described in this recommended practice includes criteria that are used to identify how well the perceived meaning matches the intended meaning for a representative sample of drivers.
CURRENT
2016-06-28
Standard
J1598_201606
This SAE Recommended Practice is applicable to all liquid-to-gas, liquid-to-liquid, gas-to-gas, and gas-to-liquid heat exchangers used in vehicle and industrial cooling systems. This document outlines the test to determine durability characteristics of the heat exchanger from vibration-induced loading.
2016-06-07
WIP Standard
AIR6908
This document provides informational background, rationale, and data (both physical testing and computer simulations) used in defining the component test methods and acceptance criteria described in SAE Aerospace Recommended Practice (ARP) 6330. ARP 6330 defines multiple test methods uses to assess the effect of seat back mounted IFE monitor changes on head blunt trauma.
CURRENT
2016-05-10
Standard
J3073_201605
This document surveys the systems used for thermal management of batteries in vehicles. Battery thermal management is important for battery performance and cycle life. The document also includes a summary of design considerations for battery thermal management and a glossary of terms.
2016-05-05
WIP Standard
J2948
This SAE Recommended Practice establishes guidelines for the operation of automotive keyless ignition systems with the goal of helping to minimize user instigated errors. For the purpose of this Recommended Practice, user instigated errors may include: • the inability to start and stop the vehicle propulsion system, • exiting the vehicle with the automatic transmission in a non-parking gear, • exiting the vehicle while the vehicle propulsion system is enabled, • exiting the vehicle while the vehicle propulsion system is disabled, but the accessory or electrical systems are active. To help minimize these errors, this Recommended Practice contains design recommendations pertaining to uniform labeling, operating logic, indication of vehicle ignition/control status, and physical control characteristics of keyless ignition systems. This Recommended Practice applies to keyless ignition controls permanently mounted in passenger cars, MPVs, and trucks 10 000 GVWR and under.
2016-03-23
WIP Standard
J2230
This SAE Standard specifies operating procedure for the exposure of automotive interior trim materials in an outdoor behind-glass apparatus in which the temperature is controlled in a 24 h cycle. The humidity is controlled during the dark (night) portion of the cycle. Specimen preparation, test durations, and performance evaluation procedures are covered in material specifications of the different automotive manufacturers.
CURRENT
2016-03-11
Standard
J2810_201603
The purpose of this SAE Standard is to provide minimum performance and operating feature requirements for the recovery of HFC-134a (R-134a) refrigerant to be returned to a refrigerant reclamation facility that will process it to the appropriate AHRI 700 Standard or allow for on-site recycling of the recovered refrigerant to SAE J2788 specifications by using SAE J2788 or SAE J3030 -certified equipment. It is not acceptable that the refrigerant removed from a mobile air-conditioning (A/C) system with this equipment be directly returned to a mobile A/C system. An identifier certified to SAE J2912 is to be used to identify the contents of the system prior to recovery of the refrigerant.
Viewing 1 to 30 of 604