Criteria

Text:
Sector:
Content:
Display:

Results

Viewing 1 to 30 of 893
2017-09-19
WIP Standard
AS6960
Seat surrounding furniture (commonly known as shells) is intended to enhance passenger comfort and privacy. They can offer additional space for reclining the seat into a bed position, additional stowage, amenities, etc. Often some amenities are located on the furniture including the front row monument installed in front of the passenger seat. The units normally attach to the same aircraft floor tracks directly in front or behind passenger seat(s) or to the seat primary structure. The unit structures are not directly integrated into the main fuselage and do not offer main supports for aircraft integrity. This Aerospace Standard (AS) establishes the minimum design, performance and qualification requirements for Seat Surrounding Furniture to be certified for installation in transport category airplanes.
2017-09-16
WIP Standard
AS8026B
This standard covers oxygen masks and breathing valves used with both panel mounted and mask mounted demand and pressure-demand oxygen regulators. Mask mounted oxygen regulators are covered under other standards, but when the mask mounted regulator incorporates an integral exhalation valve, the performance of this valve shall meet the requirements of this standard.
CURRENT
2017-09-12
Standard
ARP712C
This SAE Aerospace Recommended Practice (ARP) provides minimum standards and environmental design requirement recommendations for lighting and control in galley areas. It also addresses electrical shock hazard in galley areas. The use of "shall" in this document expresses provisions that are binding. Non-mandatory provisions use the term "should."
CURRENT
2017-08-24
Standard
ARP4822A
This SAE Aerospace Recommended Practice (ARP) reviews the basics of NVIS compatibility and discusses the specific illuminated pushbutton switch and indicator requirements for sunlight readability, color, luminance, and NVIS radiance when used in NVIS compatible cockpits.
CURRENT
2017-08-24
Standard
ARP4168B
This ARP covers three common light sources, incandescent, electroluminescent and light emitting diode that, when NVG filtered, can be used to illuminate NVG compatible aerospace crew stations. It is recognized that many other different light sources can also be used for this purpose. Also see 2.1.1 for other SAE documents that cover particular applications within the crew station environment. This ARP sets forth recommendations for the design of NVG compatible lighting, utilizing these light sources, that will meet the requirements of MIL-L-85762 Lighting, Aircraft, Interior, Night Vision Imaging System (NVIS) Compatible. This also includes the replacement document MIL-STD-3009: Lighting, Aircraft, Night Vision Imaging System (NVIS) Compatible. Although this ARP concentrates on lamp light sources for illumination, the information contained within this ARP may be directly applied to incandescent, electroluminescent and light emitting diode information display devices.
2017-08-08
WIP Standard
AIR1266B
This SAE Aerospace Information Report (AIR) outlines concepts for the design and use of fault isolation equipment that have general application. The specific focus is on fault isolation of environmental control systems (ECS) in commercial transports. Presented are general fault isolation purposes, design principles, and demonstration of compliance criteria. These are followed by three design examples to aid in understanding the design principles. Future trends in built-in-test-equipment (BITE) design are discussed, some of which represent concepts already being implemented on new equipment.
2017-07-20
WIP Standard
ARP5873B
This document presents minimum criteria for the design and installation of LED passenger reading light assemblies in commercial aircraft. The use of “shall” in this specification expresses provisions that are binding. Non-mandatory provisions use the term “should.”
CURRENT
2017-07-19
Standard
ARP798B
This SAE Aerospace Recommended Practice (ARP) covers the general requirements and test procedures recommended for use with white incandescent integrally lighted instruments. Its use should provide uniformity of illumination from instrument to instrument and legibility under daylight operation. An appendix is provided to familiarize the designer with some of the techniques used to obtain uniformity of color and illumination in various types of instruments.
2017-07-10
WIP Standard
J3151
This document defines key terms and concepts for relating effects of driver distraction on driving performance, physiological indicators, subjective assessments, or combinations thereof to effects of driver distraction on crash involvement. These concepts are intended to contribute to methodologies for assessing driver distraction metrics in terms of their reliability, repeatability, bias, and predictive or descriptive validity and distraction evaluation procedures in terms of their real-world representativeness. The actual specification of such a methodology is outside the scope of the present document. While the focus is on driver distraction evaluation for technology evaluations and driver activities, the concepts described herein may be applicable also to other forms of driving performance evaluation. The intended users of the document are practitioners in the industry, academia and other organizations with an interest in driving performance assessment and road safety.
CURRENT
2017-06-28
Standard
AS6316
This SAE Aerospace Standard (AS) documents a common understanding of terms, compliance issues, and occupant injury criteria to facilitate the design and certification of oblique facing passenger seat installations specific to Part 25 aircraft. The applicability of the criteria listed in this current release is limited to seats with an occupant facing direction greater than 18° and no greater than 45° relative to the aircraft longitudinal axis. Seats installed at angles greater than 30° relative to the aircraft longitudinal axis must have an energy absorbing rest or shoulder harness and must satisfy the criteria listed in Table 2. Later revisions are intended to provide criteria for other facing directions. Performance criteria for forward and aft facing seats are provided in AS8049 and for side facing seats in AS8049/1.
CURRENT
2017-06-07
Standard
AS7109/1B
This document has been declared "CANCELLED" as of June 2017 and has been superseded by PRI AC7109/1. By this action, this document will remain listed in the Numerical Section of the Aerospace Standards Index noting that it is superseded by PRI AC7109/1. Cancelled specifications are available from SAE.
CURRENT
2017-06-07
Standard
AS7109/2B
This document has been declared "CANCELLED" as of June 2017 and has been superseded by PRI AC7109/2. By this action, this document will remain listed in the Numerical Section of the Aerospace Standards Index noting that it is superseded by PRI AC7109/2. Cancelled specifications are available from SAE.
2017-06-07
WIP Standard
AS8010D
This document defines the minimum degree of purity and maximum levels of certain deleterious impurities allowable for aviator's breathing oxygen at the point of manufacture or generation. It covers gaseous, liquid, and chemically generated oxygen, and oxygen supplied by in situ concentration and in situ electrolysis. Different limits are established for oxygen from different sources, in recognition of differences in the ways the oxygen is stored, dispensed, and utilized, taking into account the safety of the user. These limits are not intended to specifically reflect upon the relative capabilities or merits of various technologies. Procurement documents may specify more stringent limits, where required for specific applications. Medical oxygen is not covered by this standard. In the United States, medical oxygen is a prescription drug.
2017-05-31
WIP Standard
ARP594F
The requirements presented in this document cover the design factors which might cause any part of an electrically motor driven fuel pump assembly to act as an ignition source for explosive fuel vapors within the airplane tank.
CURRENT
2017-05-25
Standard
AIR805D
The purpose of this information report is to present the factors that affect the design and development of aircraft jet blast windshield rain removal systems. Rain removal system design will generally be unique to specific aircraft. Design of these systems typically requires a preliminary design for the system based on available empirical data to be followed with a laboratory development program and a flight test validation program. Published windshield rain removal performance test data is available only for limited windshield configurations.
CURRENT
2017-05-24
Standard
AIR5742A
The scope of this document is related to the particular needs of oxygen equipment with regards to packaging and transportation. The document provides guidance for handling chemical, gaseous and liquid oxygen equipment. It summarizes national and international regulations to be taken into account for transportation on land, sea and air and provides information on classification of hazardous material. The aim of this document is to summarize information on packaging and transportation of oxygen equipment. Statements and references to regulations cited herein are for information only and should not be considered as interpretation of a law. Processes to maintain cleanliness of components and subassemblies during processing and assembly or storage of work-in-progress are outside the scope of this document. Guidance on this can be obtained from ARP1176.
CURRENT
2017-05-19
Standard
AIR1168/10A
This AIR is arranged in the following two sections: 2E - Thermodynamic Characteristics of Working Fluids, which contains thermodynamic diagrams for a number of working fluids currently in use and supplied by various industrial firms. 2F - Properties of Heat Transfer Fluids, which contains data, primarily in graphical form, on fluids that are frequently used in fluid heat transfer loops. Other properties of the environment, gases, liquids, and solids, can be found, as follows, in AIR1168/9: 2A-Properties of the Natural Environment 2B-Properties of Gases 2C-Properties of Liquids 2D-Properties of Solids
CURRENT
2017-05-19
Standard
AIR1059E
This document provides guidance concerning the maintenance and serviceability of oxygen cylinders beginning with the quality of oxygen that is required, supplemental oxygen information, handling and cleaning procedures, transfilling and marking of serviced oxygen assemblies. This document attempts to outline in a logical sequence oxygen quality, serviceability, and maintenance of oxygen cylinders. Content of this document can also be used for refilling of oxygen cylinder while installed on aircraft, directly or through an intermediate charging port.
CURRENT
2017-05-16
Standard
AS5830A
This aerospace specification defines the requirements for a threadless, flexible, conductive, self-bonding coupling assembly which, when installed on fixed cavity ferrules, provides a flexible, current carrying connection for joining tubing and components in aircraft fuel, vent and other systems. The assembled coupling is designed to provide interchangeability of parts and components between qualified manufacturers for the service life of the aircraft system. The assembled coupling is for use from -65 to +200 °F at nominal operating pressures (125 psig for -08 through -64 and 30 psig for -72 through -88). This aerospace specification is a departure from prior qualification practices for assembled couplings. Prior practice sought to validate this type of assembled coupling design by conducting a sequence of tests on sets of coupling assemblies. There were multiple test sequences and each was conducted on a different set of coupling assemblies.
CURRENT
2017-05-09
Standard
ARP5297B
This SAE Aerospace Recommended Practice (ARP) provides the qualification test procedure requirements for low wattage halogen lamps (less than 35 watts) intended for use primarily in aircraft applications. The purpose of these tests is to provide a laboratory means of determining the performance characteristics of lamps under airplane power and other environmental conditions and to verify the integrity of the lamp design and production processes.
CURRENT
2017-05-04
Standard
ARP378D
This document presents criteria for design and location of passenger reading lights in commercial aircraft. For LED reading light requirements, see ARP5873, titled: LED Passenger Reading Light Assembly.
CURRENT
2017-05-02
Standard
AS5356B
This specification covers flexible couplings for joining tubing with AS5131 Type A beaded ends for use in aircraft fuel and vent system (see 6.1).
CURRENT
2017-04-11
Standard
AMS3159G
This specification covers a liquid oxygen compatible gas-leak detecting compound in the form of a liquid.
2017-04-10
WIP Standard
ARP1270C
This ARP covers the basic criteria for the design of cabin pressure control systems (CPCS) for general aviation, commercial and military pressurized aircraft.
CURRENT
2017-03-14
Standard
ARP493B
This recommended practice is intended to recommend the basic shapes and dimensions for knobs used in aircraft. Two basic types of knobs, the bar shape and the round shape, are described, as well as several widely used variations of these two basic shapes.
CURRENT
2017-02-07
Standard
AIR1812B
This report contains background information on life cycle cost elements and key ECS cost factors. Elements of life cycle costs are defined from initial design phases through operational use. Information on how ECS designs affect overall aircraft cost and information on primary factors affecting ECS costs are discussed. Key steps or efforts for comparing ECS designs on the basis of LCC are outlined. Brief descriptions of two computer programs for estimating LCC of total aircraft programs and their use to estimate ECS LCC, are included.
2017-02-03
WIP Standard
ARP6199B

This SAE Aerospace Recommended Practice (ARP) is only applicable to 14 CFR part 25 Transport Airplane passenger seats. This document provides an approach for determining which parts on aircraft seats are required to meet the test requirements of 14 CFR part 25 Appendix F, Parts IV and V. Such materials are referred to as Heat Release Special Conditions (HRSC) compliant]. Additionally, it is recommended to use HRSC compliant materials in applications where not required.

Independent furniture related to seat installations is outside the scope of this document.

CURRENT
2017-02-02
Standard
ARP6199A
This SAE Aerospace Recommended Practice (ARP) is only applicable to 14 CFR part 25 Transport Airplane passenger seats. This document provides an approach for determining which parts on aircraft seats are required to meet the test requirements of 14 CFR part 25 Appendix F, Parts IV and V. Such materials are referred to as Heat Release Special Conditions (HRSC) compliant]. Additionally, it is recommended to use HRSC compliant materials in applications where not required. Independent furniture related to seat installations is outside the scope of this document.
2017-01-27
WIP Standard
ARP4102/4A
This document recommends design criteria for the Flight Deck Alerting System. The FAS shall enhance safety of flight by providing early crew recognition of aircraft system or component status or malfunction as well as of crew operational error. The FAS, therefore, relates to aircraft configuration and flight phase as well as the aircraft systems. To fulfill this objective, the FAS must attract the attention of the crew, must state with clarity the nature and location of the problem, and must be highly reliable and thoroughly responsive to the operational requirements and environment. Wherever possible, it should provide guidance as to the corrective action.
Viewing 1 to 30 of 893