Criteria

Text:
Content:
Display:

Results

Viewing 151 to 180 of 1604
CURRENT
2015-10-08
Standard
J1810_201510
This SAE Standard describes those factors which affect the accuracy and reliability of voltage indicating units and electrical indicating and sending units for fuel level, pressure, and temperature suitable for off-road, self-propelled work machines as described in SAE J1116 and agricultural tractors as defined in ASAE S390. Indicating units are divided into two groups, fully sealed and partially sealed. Serviceable lighting is not covered by this document unless otherwise specified. No ISO document has been found to be compatible.
CURRENT
2015-10-08
Standard
J3078/6_201510
SAE J3078/6 specifies a test method for simulating solar heating in the laboratory and measuring the radiant heat energy from a natural or simulated source. It is applicable to Off-Road Self-Propelled Work Machines as defined in SAE J1116 and Agricultural Tractors as defined in ANSI/ASAE S390.
2015-10-07
WIP Standard
J3113
SAE Jxxxx provides principles and a process for developing icons for use in electronic displays related to Off Road Work Machines as stated defined in SAE J 1116. Following the process insures that icons are derived from ISO registered graphical symbols or ISO compliant non-registered graphical symbols.
2015-10-05
WIP Standard
AS8047A
This aerospace standard (AS) defines the requirements of portable protective breathing equipment for use during smoke/fire conditions on board an aircraft.
2015-09-22
WIP Standard
AIR6256
The aim of this document is to provide a comprehensive synopsis of regulations applicable to aircraft oxygen systems. The context of physiological requirements, international regulations, operational requirements and airworthiness standards is shown to understand the role of aircraft oxygen systems and to demonstrate under which circumstances is needed on aircraft. With regards to National Aviation Regulations States are committed to the Convention on International Aviation (Chicago Convention). The majority of states have adopted, with some deviations, FAA and EASA systems including operational and airworthiness requirements. Accordingly the extent of this document is primarily focused on FAA/EASA requirements.
2015-09-18
WIP Standard
J2395
This SAE Recommended Practice applies to both Original Equipment Manufacturer (OEM) and aftermarket ITS message-generating systems for passenger vehicles and heavy trucks. The recommended practice describes the method for prioritizing ITS in-vehicle messages and/or displayed information based on a defined set of criteria. Each criterion has a fixed number of levels that are used to rate/rank a given message or information item to determine its prioritization value. The prioritization value is used to determine the priority in which simultaneous, or overlapping, in-vehicle messages are presented to the driver.
2015-09-18
WIP Standard
ARP5526E
This SAE Aerospace Recommended Practice (ARP) documents a common understanding of terms, compliance issues and design criteria to facilitate certification of seat installations specific to Part 25 aircraft. This ARP provides general guidance for seats to be installed in Part 23 aircraft and Parts 27 and 29 rotorcraft and does not specify specific designs or design methods for such certification.
2015-09-17
WIP Standard
J3110
This SAE standard applies to any and all Flushing Methods intended for use to internally clean, decontaminate, and recondition components and sections of the refrigerant circuit within a vehicle air conditioning system. This standard provides testing and acceptance criteria for determining the minimum performance of a Flushing Method, intended for use in the servicing and repair process of vehicle air conditioning system. This standard will only specify the Flushing Method performance criteria. Specifications for air conditioning Flushing Fluids are outlined in SAE J3091.
CURRENT
2015-09-15
Standard
J1994_201509
This SAE Recommended Practice is applicable to all heat exchangers used in vehicle and industrial cooling systems. This document outlines the tests to determine the heat transfer and pressure drop performance under specified conditions. This document has been reviewed and revised by adding several clarifying statements to Section 4.
CURRENT
2015-08-28
Standard
ARP1532B
This SAE Aerospace Recommended Practice (ARP) covers procedures or methods to be used for fabricating, handling, testing, and installation of oxygen lines in an aircraft oxygen system.
CURRENT
2015-08-28
Standard
ARP5873A
This document presents minimum criteria for the design and installation of LED passenger reading light assemblies in commercial aircraft. The use of “shall” in this specification expresses provisions that are binding. Non-mandatory provisions use the term “should.”
CURRENT
2015-08-28
Standard
J2064_201508
The Scope of SAE J2064 covers coupled hose assemblies intended for containing and circulating lubricant, liquid and gaseous R134a and/or R-1234yf refrigerant in automotive air-conditioning systems. Historically, requirements for the hose used in coupled automotive refrigerant air conditioning assemblies was included in SAE J2064. SAE J2064 has been changed to establish the requirements for factory and field coupled hose assemblies. SAE J3062 has been issued to define requirements for the hose used in these assemblies into its own standard. SAE J2064 also provides the necessary values used in SAE J2727 Mobile Air Conditioning System Refrigerant Emission charts for R-134a and R-1234yf. The certified coupling of MAC hose assemblies is required in meeting certain regulatory requirements. A hose which has met the requirements of SAE J3062 and certified in J2911 must be used as part of the coupled assembly.
2015-08-20
WIP Standard
AS8034C
This SAE Aerospace Standard (AS) specifies minimum performance standards for all types of Electronic Displays and Electronic Display Systems that are intended for use in the flight deck by the flightcrew in all 14 CFR Part 23, 25, 27, and 29 aircraft. The requirements and recommendations in this document are intended to apply to all installed electronic displays and electronic display systems within the flight deck, regardless of intended function, criticality, or location within the flight deck, but may also be used for non-installed electronic displays. This document provides baseline requirements and recommendations (see section 2.3 for definitions of “shall” and “should”). This document primarily addresses hardware requirements, such as electrical, mechanical, optical, and environmental. It does not address system specific functions.
2015-08-19
WIP Standard
J2831
This Information Report provides recommendations for alphanumeric messages that are supplied to the vehicle by external (e.g., RDS, satellite radio) or internal (e.g., infotainment system) sources while the vehicle is in-motion. Information/design recommendations contained in this report apply to OEM (embedded) and aftermarket systems. Ergonomic issues with regard to display characteristics (e.g., viewing angle, brightness, contrast, font design, etc.) should review ISO 15008.
CURRENT
2015-08-14
Standard
AS8049C
This SAE Aerospace Standard (AS) defines minimum performance standards, qualification requirements, and minimum documentation requirements for passenger and crew seats in civil rotorcraft, transport aircraft, and general aviation aircraft. The goal is to achieve comfort, durability, and occupant protection under normal operational loads and to define test and evaluation criteria to demonstrate occupant protection when a seat/occupant/restraint system is subjected to statically applied ultimate loads and to dynamic impact test conditions set forth in the applicable Federal Regulations 14 CFR 23, 25, 27, or 29. Guidance for test procedures, measurements, equipment, and interpretation of results is also presented to promote uniform techniques and to achieve acceptable data. While this document addresses system performance, responsibility for the seating system is divided between the seat supplier and the installation applicant.
CURRENT
2015-08-11
Standard
J2412_201508
This test method specifies the operating procedures for a controlled irradiance, xenon arc apparatus used for the accelerated exposure of various automotive interior trim components.
CURRENT
2015-07-28
Standard
AS8055A
This SAE Aerospace Standard (AS) specifies minimum performance standards for airborne binocular Head-Up Displays (HUDs) in fixed wing (14 CFR part 23, 25) aircraft; while this document is also applicable to rotorcraft (14 CFR part 27, 29) additional performance standards may be required for rotorcraft. This aerospace standard covers basic display standards, but does not include specific application requirements. Specific applications can include flight instrumentation, navigation, engine and system status, alerting, surveillance, communication, terrain awareness, weather, enhanced vision, synthetic vision and other displays. This document covers criteria for conformal and non-conformal HUD systems that are intended for use in the flight deck by the pilot or copilot. Display minimum performance characteristics are specified for standard and other environmental conditions for the purpose of product qualification.
CURRENT
2015-07-17
Standard
ARP5526D
This SAE Aerospace Recommended Practice (ARP) documents a common understanding of terms, compliance issues and design criteria to facilitate certification of seat installations specific to Part 25 aircraft. This ARP provides general guidance for seats to be installed in Part 23 aircraft and Parts 27 and 29 rotorcraft and does not specify specific designs or design methods for such certification.
CURRENT
2015-07-13
Standard
ARP1796B
This SAE Aerospace Recommended Practice (ARP) discusses design philosophy, system and equipment requirements, installation environment and design considerations for military and commercial aircraft systems within the Air Transport Association (ATA) ATA 100 specification, Chapter 36, Pneumatic. This ATA system/chapter covers equipment used to deliver compressed air from a power source to connecting points for other systems such as air conditioning, pressurization, ice protection, cross-engine starting, air turbine motors, air driven hydraulic pumps, on board oxygen generating systems (OBOGS), on board inert gas generating systems (OBIGGS), and other pneumatic demands. The engine bleed air system includes components for preconditioning the compressed air (temperature, pressure or flow regulation), ducting to distribute high or low pressure air to the using systems, and sensors/instruments to indicate temperature and pressure levels within the system.
CURRENT
2015-07-08
Standard
J3030_201507
The purpose of this SAE Standard is to establish the specific minimum equipment requirements for recovery/recycling/recharge equipment intended for use with both R-1234yf and R-134a in a common refrigerant circuit that has been directly removed from, and is intended for reuse in, mobile air-conditioning (A/C) systems. This document does not apply to equipment used for R-1234yf and R-134a having a common enclosure with separate circuits for each refrigerant, although some amount of separate circuitry for each refrigerant could be used.
CURRENT
2015-07-01
Standard
J1726_201507
This SAE Recommended Practice provides test methods and criteria for evaluating the internal cleanliness and air leakage for engine charge air coolers. This SAE Recommended Practice also provides nomenclature and terminology in common use for engine charge air coolers, related charge air cooling system components, and charge air cooling system operational performance parameters.
CURRENT
2015-06-30
Standard
J3062_201506
The Scope of SAE J3062 covers hose intended for containing and circulating lubricant, liquid and gaseous R134a and/or R-1234yf refrigerant in automotive air-conditioning systems. The hose shall be designed to minimize permeation of the refrigerant, contamination of the system, and to be functional over a temperature range of -30 to 125 °C. Specific construction details are to be agreed upon between the user and supplier. Requirements for the hose used in coupled automotive refrigerant air-conditioning assemblies had been included in SAE J2064. SAE J3062 separates requirements for the hose used in these assemblies into its own standard. SAE J2064 also provides the necessary values used in SAE J2727 Mobile Air-Conditioning System Refrigerant Emission charts for R-134a and R-1234yf. Mobile air-conditioning system refrigerant emissions rates are established in SAE J2727 Emission charts and are important.
CURRENT
2015-06-19
Standard
J860_201506
This SAE Standard is used to determine the mass per unit area, in grams per square meter, of materials used for trimming automobile interiors.
CURRENT
2015-06-18
Standard
J2364_201506
This document applies to both Original Equipment Manufacturer and aftermarket route-guidance and navigation system functions for passenger vehicles. It establishes two alternative procedures, a static method and an interrupted vision method, for determining which navigation and route guidance functions should be accessible to the driver while the vehicle is in motion. These methods apply only to the presentation of visual information and the use of manual control inputs to accomplish a navigation or route guidance task. The document does not apply to visual monitoring tasks which do not require a manual control input, such as route following. Voice-activated controls or passenger operation of controls are also excluded. There are currently no compelling data that would support the extension of this document to in-vehicle systems other than navigation systems.
2015-06-16
WIP Standard
J3103
The test procedure included in this document are used to determine a benchmark SgRP for Class A vehicles where design intent information is unknown.
CURRENT
2015-06-04
Standard
J2988_201506
The scope of this document is a technology-neutral approach to speech input and audible output system guidelines applicable for OEM and aftermarket systems in light vehicles. These may be stand-alone interfaces or the speech aspects of multi-modal interfaces. This document does not apply to speech input and audible output systems used to interact with automation or automated driving systems in vehicles that are equipped with such systems while they are in use (ref. J3016:JAN2014).
CURRENT
2015-06-04
Standard
J2802_201506
This document specifies the minimum recommendations for Blind Spot Monitoring System (BSMS) operational characteristics and elements of the user interface. A visual BSMS indicator is recommended. BSMS detects and conveys to the driver via a visual indicator the presence of a target (e.g., a vehicle), adjacent to the subject vehicle in the “traditional” Adjacent Blind Spot Zone (ABSZ). The BSMS is not intended to replace the need for interior and exterior rear-view mirrors or to reduce mirror size. BSMS is only intended as a supplement to these mirrors and will not take any automatic vehicle control action to prevent possible collisions. While the BSMS will assist drivers in detecting the presence of vehicles in their ABSZ, the absence of a visual indicator will not guarantee that the driver can safely make a lane change maneuver (e.g., vehicles may be approaching rapidly outside the ABSZ area).
CURRENT
2015-06-02
Standard
AIR1069B
Determine the required minimum oxygen concentration to be breathed prior to, during, and after a loss of cabin pressurization, and
CURRENT
2015-05-29
Standard
ARP986D
This SAE Aerospace Recommended Practice (ARP) defines recommended analysis and test procedures for qualification of pneumatically, electrically, manually, and hydraulically actuated air valves. They may be further defined as valves that function in response to externally applied forces or in response to variations in upstream and/or downstream duct air conditions in order to maintain a calibrated duct air condition (e.g., air flow, air pressure, air temperature, air pressure ratio, or air shutoff). Qualification testing performed on the airplane to verify compatibility of the valve function and stability as part of a complete system is outside the scope of this document. Refer to ARP1270 for design and certification requirements for cabin pressurization control system components. As this document is only a guide, it does not supersede or relieve any requirements contained in detailed Customer specifications.
CURRENT
2015-05-07
Standard
ARP4156C
This document defines the method for voltage identification by the use of color-coded insulators at the base of the lamps. Table 1 shows the design volts and corresponding insulator colors. The part numbers shown are for example purposes only, as an option. Insulator colors are to be easily distinguishable as green, yellow, red, and white. Additional colors may be added by a revision process as required.
Viewing 151 to 180 of 1604