Criteria

Text:
Content:
Display:

Results

Viewing 1 to 30 of 337
2017-09-22
WIP Standard
J987
This SAE Standard applies to mobile construction-type lifting cranes utilizing rope-supported, conventional and luffing type lattice boom crane structures.
2017-09-17
WIP Standard
J1257
This recommended practice applies to mobile construction type cranes with cantilevered, telescopic booms when used in lifting crane service.
2017-08-29
WIP Standard
J1366
The scope of this SAE Information Report is limited to a lift crane mounted on a fixed or floating platform, lifting loads from a vessel alongside. The size of the vessel is assumed not to exceed that of a workboat as defined in 3.15.
2017-08-29
WIP Standard
J1238
The scope of this SAE Recommended Practice is limited to cranes mounted on a fixed platform lifting loads from a vessel alongside. The size of the vessel is assumed not to exceed that of a work boat as defined in 3.14.
2017-08-24
WIP Standard
J220
This SAE Recommended Practice applies to the boomstop for the main boom of all mobile construction type cranes having rope supported booms, equipped for hook work, clamshell, magnet, grapple, or concrete bucket attachments.
2017-08-16
WIP Standard
J1028
This SAE Recommended Practice applies to stationary usage of mobile construction-type cranes, crawler or rubber-tire mounted, on outriggers or on tires, when used for lifting crane, clamshell, dragline, magnet, pile driver, or similar service.
2017-08-15
WIP Standard
J1093
This SAE Information Report applies to wire rope supported, latticed crane boom systems mounted on mobile construction type cranes for lift crane service. The purpose of this document is to establish criteria for the analytical evaluation of the basic structural competence of wire rope supported latticed crane boom systems. The criteria and procedures specified include the evaluation of elastic stability for the overall boom system and individual members of the system.
2017-08-15
WIP Standard
J999
This SAE Standard applies to cranes which are equipped to adjust the boom angle by hoisting and lowering means through rope reeving. The purpose of this standard is to define the function and to stipulate the requirements of an automatic device to prevent raising a variable angle boom above its highest specified angle.
CURRENT
2017-06-07
Standard
J820_201706
This document applies primarily to mobile cranes that lift loads by means of a drum and hoist line mechanism. It can be used to determine the hoist line speed and power of other hoist line mechanisms, if the load can be held constant and hoist line travel distance is sufficient for the accuracy of the line speed measurements prescribed. This recommended practice applies to all mechanical, hydraulic, and electric powered hoist mechanisms.
CURRENT
2017-06-07
Standard
J765_201706
This SAE Standard may be used for all revolving cranes wherein the capacity of the crane to support loads is based on its resistance to overturning. It is not applicable to cranes wherein the capacity of the crane is based on factors other than stability.
CURRENT
2016-12-09
Standard
J1790_201612
The SAE Standard applies to self-propelled, driver-operated sweepers and scrubbers as defined in SAE J2130-1 and SAE J2130-2.
2016-12-07
WIP Standard
J983
This SAE Recommended Practice applies to mobile, construction type, crane and cable excavator hand and foot controls. It should not be construed to limit the use of, or to apply to combination controls, automatic controls, or any other special operating control requirements.
CURRENT
2016-08-02
Standard
J284_201608
This SAE Recommended Practice covers the safety alert symbol intended for use on construction and industrial equipment as defined in SAE J1116 and on agricultural tractors and machinery as defined in ASABE S390.
CURRENT
2016-02-04
Standard
J1542_201602
This SAE Recommended Practice is applicable to all liquid-to-air, liquid-to-liquid, air-to-liquid, and air-to-air heat exchangers used in vehicle and industrial cooling systems. This document outlines the tests to determine durability characteristics of the heat exchanger under thermal cycling.
CURRENT
2015-11-24
Standard
J1792/2_201511
This SAE Standard establishes a test method and a definition for disclosing the performance of suction/blower fans when applied to self-propelled sweepers that solely use a pneumatic conveyance means for the collection and transfer of “sweepings” into a collection hopper.
CURRENT
2015-11-24
Standard
J1792/1_201511
This SAE Standard establishes a test method and a definition for disclosing the suction air volume performance of self-propelled sweepers that solely use a pneumatic conveyance means for the collection and transfer of “sweepings” into a collection hopper.
CURRENT
2015-11-05
Standard
J1939/75_201511
SAE J1939-75 Generator Sets and Industrial Applications defines the set of data parameters (SPNs) and messages (PGNs) for information predominantly associated with monitoring and control generators and driven equipment in electric power generation and industrial applications. The data parameters (SPNs) and messages (PGNs) previously published within this document are now published in SAE J1939DA. Applications using the SAE J1939-75 document may need to reference SAE J1939DA for the SAE J1939 parameters and messages for monitoring and controlling the power units, e.g., engines and turbines, that power the generators and driven industrial equipment.
CURRENT
2015-09-23
Standard
J2752_201509
This SAE Recommended Practice applies to compact tool carriers sometimes called, but not limited to mini-loaders, mini skid-steer loaders or compact utility loaders. Machines having a seated-operator position are excluded from this standard. However, certain attachments for a compact tool carrier may provide a seated-operator position for the operation of the attachment.
CURRENT
2015-03-27
Standard
J2130/2_201503
This SAE Standard applies to all self-propelled machines with a gross vehicle mass up to 5000 kg that are utilized to clean material from outside paved areas, parkland, floors in non-residential buildings and areas principally exposed to pedestrian traffic. Primary methods for material removal can be by mechanical, pneumatic, washing and flushing systems, or in a combination of any system.
CURRENT
2015-03-27
Standard
J2130/1_201503
This SAE Standard applies to all self-propelled machines with a gross vehicle mass greater than 5000 kg that are utilized to clean material from highways, parking lots, airfield runways, outside paved areas that are principally exposed to vehicular traffic. These machines can also be involved with road construction or repaving work. Primary methods for material removal and cleaning can be by mechanical, pneumatic, washing and flushing systems, or in a combination of any system.
CURRENT
2015-03-27
Standard
J397_201503
This SAE Standard applies to operator protective structures which may commonly be a part of construction, forestry, mining, and industrial machines.
CURRENT
2015-03-13
Standard
USCAR41
This document describes the assessment methods and physical requirements associated with the manual handling of carts and dollies, specific to material handling systems. All possible designs and applications could not be anticipated in creating these guidelines. Where there are questions of adherence to this document, such as use of an “off-the shelf” design, always consult the responsible Ergonomics Department. Force guidelines were primarily developed referencing the push/pull psychophysical Snook data contained in A Guide to Manual Materials Handling (second edition) by Mital, Nicholson and Ayoub (NY: Taylor & Francis, 1997). The force guidelines accommodate 75% of female capabilities and 99% of male capabilities. Factors that were included in the established guideline include: push / pull distances, vertical hand height, horizontal hand height, frequency and wheel / castor alignment and load rating. These factors were used to develop a conservative force guideline.
CURRENT
2015-03-10
Standard
USCAR42
This document describes the design, assessment methods and physical requirements associated with material handling systems. This would include, but not limited to manual dollies, small lot systems and kitting. All possible designs and applications could not be anticipated in creating these guidelines. Where there are questions of adherence to this document, such as use of an “off-the shelf” design, always consult the responsible Ergonomics Department.
CURRENT
2015-01-20
Standard
J1212_201501
This document applies to off-road forestry work machines defined in SAE J1116 or ISO 6814.
2015-01-08
WIP Standard
J2267
This SAE standard applies to all forestry machines exposed to the hazard of objects penetrating the front of the operator station (other than the roof). This would include: Front guards for yarders with cabs mounted next to the tower; Front guards for forestry machines capable of handling material in front of and above the deflection limiting volume (DLV); such as knuckle boom log loaders and swing to tree feller bunchers; but excluding rubber-tired or tracked front-end loaders when equipped with buckets or forks with hold down grapple arm(s); and excluding forwarders and clambunk skidders fitted with load bunk headboards meeting the requirements of ISO 11850.
CURRENT
2015-01-08
Standard
J1791_201501
This SAE standard applies to self-propelled driver operated sweepers and scrubbers as defined in SAE J2130-1.
CURRENT
2014-10-24
Standard
J748_201410
This SAE Recommended Practice has been set up by Subcommittee 4 of the Off-Road Machinery Technical Committee and is primarily for directional control valves on construction and industrial machinery equipment as referenced in SAE J1116. The purpose is to establish port area to flow relationship and match valve spool eye ends in relation to rated capacity. Port connections are optional for either the 4-bolt split flange connection or the internal straight thread "O" ring connection.
CURRENT
2014-10-24
Standard
J67_201410
This SAE Standard applies to all machines with shovel, clam, or dragline attachment.
CURRENT
2014-10-21
Standard
J2417_201410
This SAE Standard provides a uniform method to calculate the lift capacity of knuckle-boom log loaders and certain forestry equipment. It establishes definitions and specifies machine conditions for calculations. This document applies to knuckle-boom log loaders as defined in ISO 6814 and ISO 17591 and certain forestry equipment defined in ISO 6814 that have a rotating upper-structure such as feller bunchers, forwarders, harvesters, and behind the cab or rear-mounted knuckle-boom log loaders not having their own power supply. It does not apply to harvesters that are incapable of lifting a tree or log completely off the ground. This document applies to those machines that are crawler, rubber-tired, and pedestal or stationary mounted.
CURRENT
2014-08-14
Standard
J3024_201408
This document presents a catalog of safety sign text and artwork that can be used by any ready mixed concrete truck manufacturer to warn of common hazards.
Viewing 1 to 30 of 337

Filter

  • Standard
    337