Criteria

Text:
Content:
Display:

Results

Viewing 1 to 30 of 89
2017-11-21
Standard
ARP6807
The intent of the SAE Aerospace Recommended Practice (ARP) is to provide a process for users to identify the part number of AS7928 terminal lugs installed in civilian or military applications, although it can also can be used to identify terminals that have been stored incorrectly. This ARP is subject to change to keep pace with experience and technical advances of AS7928 terminals. A current set of tables are provided to list and identify current AS7928 terminal lug configurations per the associated specification detail sheet and terminal lug configuration. Specific configuration details, graphic, size and marking information for each individual terminal lug is provided to assist the product user with accurate selection for replacement or identification.
2017-11-03
Standard
AS478P
This standard provides the following: a. Definition of terms pertaining to marking. b. Symbols for marking location. c. Requirements and restrictions for permanent markings. d. Types of marking methods. e. Rules for designating marking methods. f. Table listing marking methods.
2017-10-12
Standard
AMS2804D
This specification covers the requirements for identification of castings.
2017-09-19
Standard
J2710_201709
This SAE Recommended Practice describes test methods for measuring and identifying the natural frequencies for the lower order modes of an inflated radial tire with a fixed spindle while expending modest effort and employing a minimum of test equipment. The methods apply to any size of radial tire so long as the test equipment is properly scaled to conduct the measurements for the intended test tire. Two types of boundary conditions are considered for the tire: unloaded and loaded against a flat surface. The test involves the performance and measurement of an input vibratory force (excitation) to the tire and the corresponding vibratory output (response). The data are suitable for use in determining parameters for road load models and for comparative evaluations of the measured properties in research and development. NOTE 1—The focus of this standard is identification and reporting of the lower order natural frequencies of the tire using a simple test procedure.
2017-08-14
Standard
J2927_201708
This SAE standard applies to refrigerant identification equipment to be used for identifying an acceptable level of R-1234yf purity in a refrigerant tank or vehicle MAC system labeled as containing R-1234yf, and not misidentify other refrigerants, per 5.7.
2017-07-06
Standard
AS85848A
This specification establishes the requirements for various types of identification sleeving that will shrink to a predetermined size upon the application of heat after it has been marked. Continuous operating temperature ratings range from -55° to 175°C (-67° to 347°F). (See 6.1).
2017-04-28
WIP Standard
J2892
This document establishes standard graphical symbols and color conventions for use in either still (static) or animated graphics used for communicating service information. This document’s purpose is to communicate conventions for using those symbols and colors to accurately and consistently communicate intended information via graphics-based documentation. These practices are intended for use in service procedures, assembly instructions, training materials, and similar applications when trying to minimize the amount of human natural language text used within the document. The still and animated graphical conventions referenced should support effective communication via paper and “traditional” electronic media. The conventions can also extend to documenting via additional electronic delivery paradigms such as Augmented Reality (AR).
2017-03-28
Standard
J1344_201703
This SAE Recommended Practice provides a system for marking plastic parts to designate the type of material from which the part was fabricated.
2017-03-28
Standard
AMS2808E
This specification covers the requirements for identification of forgings, including die forgings, hand forgings, and rolled rings.
2017-03-02
Standard
J3108_201703
This recommended practice prescribes clear and consistent labeling methodology for communicating important xEV high voltage safety information. Examples of such information include identifying key high voltage system component locations and high voltage disabling points. These recommendations are based on current industry best practices identified by the responder community. Although this recommended practice is written for xEVs with high voltage systems, these recommendations can be applied to any vehicle type.
2017-02-21
Standard
AS6023
The scope of this document is to: Provide a requirements document for RFID Tag Manufacturers to produce active RFID tags for the Aerospace industry. Identify the minimum performance requirements for active RFID tags to be used on or in close proximity to aircraft. Specify the test requirements specific to active RFID tags for aircraft use, in addition to RTCA DO-160 compliance requirements separately called out in this document. Identify existing standards applicable to active RFID Tag. Provide a certification standard for RFID tags which will use permanently-affixed installation on aircraft and aircraft parts. Battery standards are separately captured and not included in this document.
2017-02-09
Standard
AMS2800E
This specification covers the requirements for identification of finished parts.
2017-01-24
Standard
AIR5575A
This SAE Aerospace Information Report (AIR) discusses the often overlooked relationship between hot stamp marking and the environmental conditions that contribute aircraft wiring problems and discusses current beliefs of military service experts, regulatory agencies and industry standard writing bodies about the potential hazards imposed by the hot stamping process.
2016-12-01
Standard
ARP5369B
These guidelines have been written to provide process information regarding the hot stamp method of marking wire identification directly on aerospace wires and cables.
2016-11-22
Standard
AMS2817G
This specification covers procedures which will provide protection of elastomeric seals and seal assemblies such as O-rings, cap seal assemblies, and other designs from contamination by foreign materials and handling / transportation / storage damage prior to installation and ensure positive identification by part number of each piece until it is installed.
2016-10-13
Standard
J2892_201610
This document establishes standard graphical symbols and color conventions for use in either still (static) or animated graphics used for communicating service information. This document’s purpose is to communicate conventions for using those symbols and colors to accurately and consistently communicate intended information via graphics-based documentation. These practices are intended for use in service procedures, assembly instructions, training materials, and similar applications when trying to minimize the amount of human natural language text used within the document. The still and animated graphical conventions referenced should support effective communication via paper and “traditional” electronic media. The conventions can also extend to documenting via additional electronic delivery paradigms such as Augmented Reality (AR).
2016-10-03
WIP Standard
AS6462B
This set of criteria shall be utilized by accredited Certification Bodies (CBs) to establish compliance, and grant certification to AS5553A, Aerospace Standard; Counterfeit Electronic Parts; Avoidance, Detection, Mitigation, and Disposition.
2016-05-26
Standard
J2981_201605
To provide the industry with the means to apply a set of rules for identifying and providing a common numbering system for lead acid starting batteries.
2016-05-10
WIP Standard
J1817
This SAE Recommended Practice describes a marking system to distinguish long-stroke from standard stroke for service, parking, and combination air-brake actuators, roto-chambers, and components. Said actuators are used for applying cam and disc-type foundation brakes by slack adjuster means.
2016-04-05
Standard
J3071_201604
This SAE Battery Identification and Cross Contamination Prevention document is intended to provide information that may be applicable to all types of Rechargeable Energy Storage System (RESS) devices. It is important to develop a system that can facilitate sorting by chemistry. The recycler is interested in the chemistry of the RESS. This is true for the recyclers of Lead Acid, Lithium Ion, Nickel Cadmium etc. Thus recyclers of RESS will receive RESS from automotive, commercial, and industrial applications. These RESS have the potential to be contaminated with a RESS of an incompatible chemistry. It is recognized that mitigation methods to reduce or eliminate the introduction of incompatible chemistries into a given recycling stream would also benefit safety and the environment.
2016-03-15
Standard
J1817_201603
This SAE Recommended Practice describes a marking system to distinguish long-stroke from standard stroke for service, parking, and combination air-brake actuators, roto-chambers, and components. Said actuators are used for applying cam and disc-type foundation brakes by slack adjuster means.
2015-12-20
Standard
AS5678A
The scope of this document is to: Provide a requirements document for RFID Tag Manufacturers to produce passive-only UHF RFID tags for the aerospace industry. Identify the minimum performance requirements specific to the Passive UHF RFID Tag to be used on aircraft parts, to be accessed only during ground operations. Specify the test requirements specific to Passive UHF RFID tags for airborne use, in addition to RTCA DO-160 compliance requirements separately called out in this document. Identify existing standards applicable to Passive UHF RFID Tag. Provide a certification standard for RFID tags which will use permanently-affixed installation on aircraft and aircraft parts.
2015-12-08
Standard
AMSR83248/1A
The purpose of this specification sheet is to set up a standardized part numbering system for o-rings procured to MIL-R-83248, Class 1 (75 ± 5 hardness).
2015-12-08
Standard
AMSR83248/2A
The purpose of this specification sheet is to set up a standardized part numbering system for o-rings procured to MIL-R-83248, Class 2 (90 ± 5 hardness).
2015-11-24
Standard
J846_201511
This coding system is intended to provide a convenient means of identifying the various tube, pipe, hydraulic hose type and hose fittings, not intended for use in aircraft and of transmitting technical or engineering information relating to them wherever drawings or other pictorial media may not be readily available. The code has been kept flexible to permit expansion to cover new fitting categories or styles and, if the need develops, the inclusion of additional materials. The system is also compatible with automatic data processing equipment. It is not intended that this code should supersede established systems or means of identification. Therefore, it should be the prerogative of the user to apply the code which best satisfies his requirements.
2015-07-30
Standard
AIR1273B
This SAE Aerospace Information Report (AIR) establishes a positive identification of the functions and, if applicable, the hazards and direction of flow of pipe, hose, tube, or electrical conduit lines.
2015-06-18
Standard
AS6886
Counterfeiting of refrigerants has seen a dramatic rise over the past two decades. This rise can be partially attributed to global restrictions placed on production and use of refrigerants by the 1987 Montreal and the 1997 Kyoto Protocols (1, 2). These Protocols regulate the gradual phase-out and strict regulations on the use of refrigerants with high Ozone Depletion Potential (ODP) and high Global Warming Potential (GWP). These protocols require that older refrigerants shall be replaced with newer, more expensive, and environmentally friendly chemicals (3, 4) and necessitates redesigned or replaced equipment to operate efficiently with these new refrigerants.
2015-05-12
Standard
J1449_201505
This SAE Recommended Practice specifies graphic symbols for operator controls, gauges, tell-tales, indicators, instructions, and warning against risks in small craft and for engines and other equipment intended to be used in small craft.
Viewing 1 to 30 of 89