Criteria

Text:
Content:
Display:

Results

Viewing 1 to 30 of 3311
2017-07-19
WIP Standard
AS5420G
This SAE Aerospace Standard (AS) covers the requirements for a flexible, lightweight, low pressure, self-extinguishing, integrally heated silicone hose assembly. The hose has a fully fluorinated fluoropolymer inner liner and is primarily intended for use in aircraft potable water systems with an environmental operating temperature range of -65 °F (-54 °C) to +160 °F (+71 °C).
CURRENT
2017-07-18
Standard
ARP4386D
This SAE Aerospace Recommended Practice (ARP) provides the technical terms and nomenclature, together with their definitions and abbreviations/acronyms that are used in aerospace fluid power, actuation and control systems. NOTE: ARP490 and ARP4493 are sources for definitions specifically for electrohydraulic servovalves.
CURRENT
2017-07-14
Standard
J1754/1_201707
This SAE Standard covers steel wire reinforced rubber hose assemblies using connectors specified in SAE J516 for use in hydraulic systems using petroleum based hydraulic fluids with maximum working pressures of 1.7 to 42 MPa. See Part 2, Table 7 for hose operating temperature ranges and identification codes. NOTE: Working pressure is defined as maximum system pressure.
CURRENT
2017-07-07
Standard
AS21905D
Scope unavailable.
CURRENT
2017-07-07
Standard
AS21910E
Scope unavailable.
CURRENT
2017-07-06
Standard
AS21911D
SCOPE IS UNAVAILABLE.
CURRENT
2017-07-05
Standard
AS4688C
(A) Propose to replace .5625-16 UNJF with .5625-18 UNJF on Table 3 and other editorial changes (ex. replace ARP4296 with AS4296). (B) Propose revision to add conductive high purity aluminum coating per MIL-DTL-83488 for aluminum alloy fittings. The W code aluminum parts with new finish will be distinguished by new finish code V at the end of part number.
2017-06-30
WIP Standard
AIR7975
Generic overview of fuel system design and sizing, and guidelines for installation of various fuel system elements
CURRENT
2017-06-28
Standard
AS21906D
SCOPE IS UNAVAILABLE.
CURRENT
2017-06-28
Standard
AS21909E
SCOPE IS UNAVAILABLE.
CURRENT
2017-06-28
Standard
AS21912D
SCOPE IS UNAVAILABLE.
CURRENT
2017-06-28
Standard
AS21914D
Scope unavailable.
2017-06-27
WIP Standard
J643
The range of test conditions on the dynamometer shall be sufficient to determine the primary operating characteristics corresponding to the full range of vehicle operations. The characteristics to be determined are: a. Torque ratio versus speed ratio and output speed b. Input speed versus speed ratio and output speed c. Efficiency versus speed ratio and output speed d. Capacity factor versus speed ratio and output speed e. Input torque versus input speed
2017-06-22
WIP Standard
AS4200B
SCOPE IS UNAVAILABLE.
CURRENT
2017-06-22
Standard
AS893E
To Stabilize AS893D - issued 1-15-76 per MIL-F-18280 for O2 and GSE only; revised 4 times (12-1-83 to add O2 cleaning requirement and part id note, 1995-12 to reformat to SAE template and revised title, 2008-03 to add cad note, change proc spec to AS4842/2 and associated QML requirements, update matl inactive/can'd specs to active ones, revised wrench flat tolerances, and inactivated 'D' matl for new design, 2009-11 to update to current SAE template along with Table updates and add 'D' inactive effectivity date; reaffirmed twice; April 1983 & 2007-08. No other significant changes to the standard.
CURRENT
2017-06-21
Standard
AS4665C
SCOPE IS UNAVAILABLE.
CURRENT
2017-06-21
Standard
AS897E
SCOPE IS UNAVAILABLE.
CURRENT
2017-06-21
Standard
AS4664D
SCOPE IS UNAVAILABLE.
2017-06-21
WIP Standard
AS5188C
SCOPE IS UNAVAILABLE.
CURRENT
2017-06-21
Standard
AS5230D
SCOPE IS UNAVAILABLE.
CURRENT
2017-06-21
Standard
AS1004G
SCOPE IS UNAVAILABLE.
CURRENT
2017-06-21
Standard
AS1008J
SCOPE IS UNAVAILABLE.
CURRENT
2017-06-21
Standard
AS1007K
SCOPE IS UNAVAILABLE.
CURRENT
2017-06-20
Standard
AS33931C
SCOPE IS UNAVAILABLE.
CURRENT
2017-06-19
Standard
J1335_201706
Applies to hydraulic cylinders which are components of Off-Road Self-Propelled Work Machines defined in SAE J1116.
CURRENT
2017-06-16
Standard
ARP584D
This SAE Aerospace Recommended Practice (ARP) addresses the design, installation, and testing of coiled tube assemblies ranging from 1/4 inch (6.3 mm) to 1.0 inch (25 mm) diameter using CRES tubing per AMS-T-6845, unless otherwise approved by the Procuring Activity. This ARP specifically details three different configurations of coiled tubing. These configurations should be compatible with pressure levels up to 3000 psi (20.7 MPa) upon the completion of the analysis for the actual stress and life requirement of the intended application. However, formal qualification tests are recommended to verify the satisfactory installation, clamping, and the life of each unique design. NOTE: Refer to ARP4146 for information on design of coiled tube assemblies using Titanium tubing.
2017-06-15
WIP Standard
AS6034
Create an AS standard for a high temperature loop type support clamp in 625 nickel alloy in sizes shown on AS9025 and oversized for use with .028" wearsleeves.
CURRENT
2017-06-14
Standard
AS18280F
This SAE Aerospace Standard (AS) establishes the requirements for 24° cone flareless fluid connection fittings and nuts, internally or externally swaged, preset, or welded sleeves for use in aircraft fluid systems at nominal operating pressures up to and including 3000 psi.
2017-06-08
WIP Standard
AS598A
This SAE Aerospace Standard (AS) defines the materials, apparatus and procedure for microscopic sizing and counting of particulate contamination of fluid power systems by membrane filtration using microscopic counting.
2017-06-08
WIP Standard
AS5461C
SCOPE IS UNAVAILABLE.
Viewing 1 to 30 of 3311