Criteria

Text:
Topic:
Content:
Display:

Results

Viewing 1 to 30 of 1001
2017-08-16
WIP Standard
J1028
This SAE Recommended Practice applies to stationary usage of mobile construction-type cranes, crawler or rubber-tire mounted, on outriggers or on tires, when used for lifting crane, clamshell, dragline, magnet, pile driver, or similar service.
2017-08-15
WIP Standard
J999
This SAE Standard applies to cranes which are equipped to adjust the boom angle by hoisting and lowering means through rope reeving. The purpose of this standard is to define the function and to stipulate the requirements of an automatic device to prevent raising a variable angle boom above its highest specified angle.
2017-08-15
WIP Standard
J1454
This SAE Standard describes a laboratory test procedure for comparatively evaluating the durability and fatigue life qualities of a complete seat cushion by submitting the seating surface of the cushion to repetitive compressive and rotational loading with a simulated human buttocks. This document provides a uniform method of dynamically testing the durability of seat cushions on a comparative basis.
2017-08-15
WIP Standard
J1093
This SAE Information Report applies to wire rope supported, latticed crane boom systems mounted on mobile construction type cranes for lift crane service. The purpose of this document is to establish criteria for the analytical evaluation of the basic structural competence of wire rope supported latticed crane boom systems. The criteria and procedures specified include the evaluation of elastic stability for the overall boom system and individual members of the system.
2017-08-07
WIP Standard
ARP5674A
This document is intended to be used for laser systems mounted on aircraft and intended for use in the navigable airspace. This does not include lasers onboard aircraft where the beam is contained within an enclosure so that the beam cannot enter into airspace, nor does it include lasers from satellites and spacecraft in outer space. It may be used in conjunction with: AS4970, ARP5535, ARP5572, ARP5293, and the ANSI Z136 laser safety standards.
2017-08-07
WIP Standard
ARP5290A
This document sets forth several acceptable methods of laser beam divergence measurement techniques.
2017-08-03
WIP Standard
J899
This SAE Standard provides seat dimensions and adjustments for the design of operator's seat.
2017-07-20
WIP Standard
ARP5873B
This document presents minimum criteria for the design and installation of LED passenger reading light assemblies in commercial aircraft. The use of “shall” in this specification expresses provisions that are binding. Non-mandatory provisions use the term “should.”
2017-07-10
WIP Standard
J3151
This document defines key terms and concepts for relating effects of driver distraction on driving performance, physiological indicators, subjective assessments, or combinations thereof to effects of driver distraction on crash involvement. These concepts are intended to contribute to methodologies for assessing driver distraction metrics in terms of their reliability, repeatability, bias, and predictive or descriptive validity and distraction evaluation procedures in terms of their real-world representativeness. The actual specification of such a methodology is outside the scope of the present document. While the focus is on driver distraction evaluation for technology evaluations and driver activities, the concepts described herein may be applicable also to other forms of driving performance evaluation. The intended users of the document are practitioners in the industry, academia and other organizations with an interest in driving performance assessment and road safety.
2017-06-07
WIP Standard
AS8010D
This document defines the minimum degree of purity and maximum levels of certain deleterious impurities allowable for aviator's breathing oxygen at the point of manufacture or generation. It covers gaseous, liquid, and chemically generated oxygen, and oxygen supplied by in situ concentration and in situ electrolysis. Different limits are established for oxygen from different sources, in recognition of differences in the ways the oxygen is stored, dispensed, and utilized, taking into account the safety of the user. These limits are not intended to specifically reflect upon the relative capabilities or merits of various technologies. Procurement documents may specify more stringent limits, where required for specific applications. Medical oxygen is not covered by this standard. In the United States, medical oxygen is a prescription drug.
CURRENT
2017-05-26
Standard
J2396_201705
This SAE Recommended Practice defines key terms used in the description and analysis of video based driver eye glance behavior, as well as guidance in the analysis of that data. The information provided in this practiced is intended to provide consistency for terms, definitions, and analysis techniques. This practice is to be used in laboratory, driving simulator, and on-road evaluations of how people drive, with particular emphasis on evaluating Driver Vehicle Interfaces (DVIs; e.g., in-vehicle multimedia systems, controls and displays). In terms of how such data are reduced, this version only concerns manual video-based techniques. However, even in its current form, the practice should be useful for describing the performance of automated sensors (eye trackers) and automated reduction (computer vision).
CURRENT
2017-05-24
Standard
AIR5742A
The scope of this document is related to the particular needs of oxygen equipment with regards to packaging and transportation. The document provides guidance for handling chemical, gaseous and liquid oxygen equipment. It summarizes national and international regulations to be taken into account for transportation on land, sea and air and provides information on classification of hazardous material. The aim of this document is to summarize information on packaging and transportation of oxygen equipment. Statements and references to regulations cited herein are for information only and should not be considered as interpretation of a law. Processes to maintain cleanliness of components and subassemblies during processing and assembly or storage of work-in-progress are outside the scope of this document. Guidance on this can be obtained from ARP1176.
CURRENT
2017-05-19
Standard
AIR1059E
This document provides guidance concerning the maintenance and serviceability of oxygen cylinders beginning with the quality of oxygen that is required, supplemental oxygen information, handling and cleaning procedures, transfilling and marking of serviced oxygen assemblies. This document attempts to outline in a logical sequence oxygen quality, serviceability, and maintenance of oxygen cylinders. Content of this document can also be used for refilling of oxygen cylinder while installed on aircraft, directly or through an intermediate charging port.
CURRENT
2017-05-09
Standard
ARP5297B
This SAE Aerospace Recommended Practice (ARP) provides the qualification test procedure requirements for low wattage halogen lamps (less than 35 watts) intended for use primarily in aircraft applications. The purpose of these tests is to provide a laboratory means of determining the performance characteristics of lamps under airplane power and other environmental conditions and to verify the integrity of the lamp design and production processes.
CURRENT
2017-05-04
Standard
ARP378D
This document presents criteria for design and location of passenger reading lights in commercial aircraft. For LED reading light requirements, see ARP5873, titled: LED Passenger Reading Light Assembly.
2017-04-20
WIP Standard
J1362
SAE J1362 presents graphical symbols for use on operator controls and other displays on off-road work machines as defined in SAE J1116 plus mobile cranes but excluding agricultural tractors. Symbols for agricultural tractors are covered by ASABE S304, ISO 3767-1, and ISO 3767-2.
2017-04-10
WIP Standard
ARP1270C
This ARP covers the basic criteria for the design of cabin pressure control systems (CPCS) for general aviation, commercial and military pressurized aircraft.
CURRENT
2017-03-14
Standard
ARP493B
This recommended practice is intended to recommend the basic shapes and dimensions for knobs used in aircraft. Two basic types of knobs, the bar shape and the round shape, are described, as well as several widely used variations of these two basic shapes.
CURRENT
2017-03-07
Standard
AS25050B
This specification covers the chromaticity and transmission requirements of aircraft lighting and light transmitting ware in descending order of transmission. It is intended for use in aviation lighting.
CURRENT
2017-02-02
Standard
ARP577E
This SAE Aerospace Recommended Practice (ARP) specifies criteria for the design, development, standardization, and comprehension testing of placards containing pictures, drawings, symbols, and/or written instructions for locating and operating aircraft emergency equipment. This ARP also provides guidance in the selection and implementation of warning placards intended to instruct occupants inside, and rescue personnel outside, the aircraft.
2017-01-27
WIP Standard
ARP5628A
This document recommends criteria and requirements for a Final Approach Spacing System (FASS) for transport aircraft. This is an Aerospace Recommended Practice to support the development of a Final Approach Spacing System (FASS) for Approach Spacing for Instrument Approaches (ASIA) operations.
2017-01-18
WIP Standard
AIR6190A
This document provides information on provisions for passengers with disabilities on board commercial aircraft. In this context the term "provision of medical oxygen" shall be understood as application of oxygen on board an aircraft not linked to (post) decompression in the sense of Airworthiness Requirements FAR/CS 25 and Operational Regulations of FAR 121/135. Information about available equipment and physiological treatment in clinical practice will be provided in this document. It covers the use of oxygen concentrators according to guidance of FAR Advisory Circular AC120-95.
2017-01-16
WIP Standard
ARP693E
This document includes requirements of installations of adequate landing and taxiing lighting systems in aircraft of the following categories: a. Single engine personal and/or liaison type b. Light twin engine c. Large multiengine propeller d. Large multiengine turbojet e. Military high performance fighter and attack f. Helicopter
CURRENT
2017-01-05
Standard
AIR5661A
This SAE Aerospace Information Report (AIR) provides data and general analysis methods for calculation of internal and external, pressurized and unpressurized airplane compartment pressures during rapid discharge of cabin pressure. References to the applicable current FAA and EASA rules and advisory material are provided. While rules and interpretations can be expected to evolve, numerous airplanes have been approved under current and past rules that will have a continuing need for analysis of production and field modifications, alterations and repairs. The data and basic principles provided by this report are adaptable to any compartment decompression analysis requirement.
CURRENT
2017-01-04
Standard
ARP6239
This SAE Aerospace Recommended Practice (ARP) recommends the design and features of aircraft demonstration emergency equipment for use in passenger safety briefings.
CURRENT
2017-01-04
Standard
AS1303B
This SAE Aerospace Standard (AS) applies to a portable chemical oxygen generator assembly intended for the following uses: First aid treatment of aircraft occupants after an emergency descent following a decompression or other emergency condition. Use by cabin attendants to maintain their mobility after a decompression.
CURRENT
2017-01-03
Standard
ARP583J
This SAE Aerospace Recommended Practice (ARP) provides guidance for the design and location of cabin crew stations, including emergency equipment installations at or near such stations, so as to enable the cabin crew to function effectively in emergency situations, including emergency evacuations. Recommendations regarding design of cabin crew stations apply to all such stations; recommendations regarding location apply to those stations located near or adjacent to floor level exits.
CURRENT
2016-12-08
Standard
J3114_201612
The aim of this Information Report is to provide terms and definitions that are important for the user’s interaction with L2 through L4 driving automation system features per SAE J3016, which provides a basis for this document.
2016-12-07
WIP Standard
J983
This SAE Recommended Practice applies to mobile, construction type, crane and cable excavator hand and foot controls. It should not be construed to limit the use of, or to apply to combination controls, automatic controls, or any other special operating control requirements.
2016-11-18
WIP Standard
J100
This SAE Recommended Practice establishes boundaries for shade bands on glazed surfaces in class "A" vehicles. These boundaries are located so that the shade band can provide occupant comfort and driver vision protection from glare, with respect to solar radiation, under some lighting and driving conditions. Since shade bands transmit less visible light than adjacent glazed surfaces, the shade band boundaries establish boundaries for the driver's field of view.
Viewing 1 to 30 of 1001

Filter

  • Standard
    1001