Criteria

Text:
Content:
Display:

Results

Viewing 121 to 150 of 1265
2015-06-16
WIP Standard
J3103
The test procedure included in this document are used to determine a benchmark SgRP for Class A vehicles where design intent information is unknown.
CURRENT
2015-06-12
Standard
AIR6258
This document is intended to describe technologies available, application needs, and operational requirements relating to the use of fiber optic sensing systems on aerospace platforms: To define standard terminology used in describing fiber optic sensing systems and their performance. To identify current interfaces used for fiber optic sensing systems. To define environmental, reliability, and maintainability capabilities of fiber optic sensing system components. To describe the fiber optic sensor and instrumentation technologies that forms the current state of the art. To describe current and future unmet needs of the aerospace industry for measurements using fiber optic sensors.
CURRENT
2015-06-04
Standard
J2988_201506
The scope of this document is a technology-neutral approach to speech input and audible output system guidelines applicable for OEM and aftermarket systems in light vehicles. These may be stand-alone interfaces or the speech aspects of multi-modal interfaces. This document does not apply to speech input and audible output systems used to interact with automation or automated driving systems in vehicles that are equipped with such systems while they are in use (ref. J3016:JAN2014).
CURRENT
2015-06-04
Standard
J2802_201506
This document specifies the minimum recommendations for Blind Spot Monitoring System (BSMS) operational characteristics and elements of the user interface. A visual BSMS indicator is recommended. BSMS detects and conveys to the driver via a visual indicator the presence of a target (e.g., a vehicle), adjacent to the subject vehicle in the “traditional” Adjacent Blind Spot Zone (ABSZ). The BSMS is not intended to replace the need for interior and exterior rear-view mirrors or to reduce mirror size. BSMS is only intended as a supplement to these mirrors and will not take any automatic vehicle control action to prevent possible collisions. While the BSMS will assist drivers in detecting the presence of vehicles in their ABSZ, the absence of a visual indicator will not guarantee that the driver can safely make a lane change maneuver (e.g., vehicles may be approaching rapidly outside the ABSZ area).
CURRENT
2015-06-04
Standard
J2426_201506
This SAE Recommended Practice describes the test procedures for conducting simulated dynamic lateral rollover restraint system tests for heavy truck applications. Its purpose is to establish recommended test procedures that will standardize restraint system testing for heavy trucks. Descriptions of the test set-up, test instrumentation, photographic/video coverage, and the test fixtures are included.
CURRENT
2015-06-02
Standard
AIR1069B
Determine the required minimum oxygen concentration to be breathed prior to, during, and after a loss of cabin pressurization, and
CURRENT
2015-05-07
Standard
J2876_201505
This procedure establishes a recommended practice for performing a Low Speed Knee Slider test to the Hybrid III 50th Male Anthropomorphic Test Device (ATD or crash dummy). This test was created to satisfy the demand from industry to have a certification test which produces similar results to an actual low energy automotive impact test. An inherent problem exists with the current certification procedure because the normal (2.75 m/s) knee slider test has test corridors that do not represent typical displacements seen in these low energy impact tests. The normal test corridors specify a force requirement at 10 mm and at 18 mm, while the low speed test needs to have a peak displacement around 10 mm.
CURRENT
2015-05-07
Standard
J1757/1_201505
The scope of this SAE Standard is to provide methods to determine display optical performance in all typical automotive ambient light illumination - with focus on High Ambient Contrast Ratio, which is critical for display legibility in a sunshine environment. It covers indoor measurements and simulated outdoor lighting. It is not the scope of this document to set threshold values for automotive compliance. However some recommended values are presented for reference.
2015-05-05
WIP Standard
J3099
Presents the seating accommodation model used to determine seat track length for accommodation in design.
CURRENT
2015-04-30
Standard
J1174_201504
This SAE Recommended Practice establishes the instrumentation and procedure to be used in measuring the operator ear sound level for engine powered equipment under 30 kW (40 bhp). The sound levels obtained by using this procedure are representative of the sound levels generated by the equipment under typical operating conditions. It is intended to include equipment such as lawn mowers, snow blowers, and tillers. It is not intended to include equipment designed primarily for operation on highways or within factories or buildings, or vehicles such as motorcycles, snowmobiles, and pleasure motorboats that are covered by other SAE Standards or Recommended Practices. This procedure does not cover handheld equipment such as chainsaws, leaf blowers, and trimmers. This SAE Recommended Practice may also be used when measuring the operator ear sound level of similar equipment powered by electricity or other power sources.
CURRENT
2015-03-30
Standard
USCAR43
This document describes the design and assembly force guidelines for conventional shipping caps, torque caps, and body plugs. All possible design and applications could not be anticipated in creating these guidelines. Where there are questions of adherence to to this document, such as use of an “off-the-shelf” design, always consult the responsible Ergonomics Department.
CURRENT
2015-03-27
Standard
J1819_201503
The scope of this SAE Recommended Practice is to promote compatibility between child restraint systems and vehicle seats and seat belts. Design guidelines are provided to vehicle manufacturers for certain characteristics of seats and seat belts, and to child restraint system (CRS) manufacturers for corresponding CRS features so that each can be made more compatible with the other. The Child Restraint System Accommodation Fixture, shown in Figure 1, is used to represent a CRS to the designers of both the vehicle interior and the CRS for evaluation of each product for compatibility with the other. The features of the accommodation fixture are described as each is used. A CRS accommodation template of transparent plastic, not shown, represents the side of the accommodation fixture for use in approximating its installed position on design drawings.
CURRENT
2015-03-13
Standard
USCAR41
This document describes the assessment methods and physical requirements associated with the manual handling of carts and dollies, specific to material handling systems. All possible designs and applications could not be anticipated in creating these guidelines. Where there are questions of adherence to this document, such as use of an “off-the shelf” design, always consult the responsible Ergonomics Department. Force guidelines were primarily developed referencing the push/pull psychophysical Snook data contained in A Guide to Manual Materials Handling (second edition) by Mital, Nicholson and Ayoub (NY: Taylor & Francis, 1997). The force guidelines accommodate 75% of female capabilities and 99% of male capabilities. Factors that were included in the established guideline include: push / pull distances, vertical hand height, horizontal hand height, frequency and wheel / castor alignment and load rating. These factors were used to develop a conservative force guideline.
CURRENT
2015-03-10
Standard
USCAR42
This document describes the design, assessment methods and physical requirements associated with material handling systems. This would include, but not limited to manual dollies, small lot systems and kitting. All possible designs and applications could not be anticipated in creating these guidelines. Where there are questions of adherence to this document, such as use of an “off-the shelf” design, always consult the responsible Ergonomics Department.
CURRENT
2015-02-18
Standard
AMS1452C
This specification covers a general-purpose disinfectant in the form of a concentrated liquid.
CURRENT
2015-02-10
Standard
ARP5535A
This document applies to safety observers or spotters involved with the use of outdoor laser systems. It may be used in conjunction with SAE Aerospace Standard (AS4970) “Human Factors Considerations for Outdoor Laser Operations in the Navigable Airspace.” Additional control measures may be applicable and are listed in ANSI Z136.6.
CURRENT
2015-02-03
Standard
J2862_201502
This user’s manual covers the small adult female Hybrid III test dummy. It is intended for technicians who work with this device. It covers the construction and clothing, disassembly and reassembly, available instrumentation, external dimensions and segment masses, as well as certification and inspection test procedures. It includes instructions for safe handling of the instrumented dummy, repairing dummy flesh, and adjusting the joints throughout the dummy.
2015-02-02
WIP Standard
AS6339
Purpose of this standard is to provide minimum performance requirements of a Full Face Quick Donning Mask Assembly (FFQDM) with integrated regulator including appropriate stowage facility regarding functionality under conditions of aircraft environments. Function and performance requirements shall take into account varying modes of use and handling during aircraft operation according to operational requirements.
2015-01-28
WIP Standard
ARP6321
The scope of this document is to provide those recommended practices considered essential for all air carrier first officer initial training programs. The recommended practices contained within this document are intended primarily for the guidance of passenger and cargo air carriers, and training providers. This document is also intended to guide those responsible for rule making and the provision of oversight of organizations involved in air carrier first officer initial training programs. Any professional pilot training organization may benefit from a review of the recommendations contained in this document.
2015-01-13
WIP Standard
J1052
This SAE Standard describes head position contours and procedures for locating the contours in a vehicle. Head position contours are useful in establishing accommodation requirements for head space and are required for several measures defined in SAE J1100. Separate contours are defined depending on occupant seat location and the desired percentage (95 and 99) of occupant accommodation.
HISTORICAL
2015-01-08
Standard
J185_201501
Minimum criteria are provided for steps, stairways, ladders, walkways, platforms, handrails, handholds, guardrails, and entrance openings which permit ingress to and egress from operator, inspection, maintenance or service platforms on off-road work machines parked in accordance with the manufacturer's instructions.
CURRENT
2014-12-03
Standard
J1521_201412
This SAE Recommended Practice describes two-dimensional, 95th percentile truck driver, side view, seated shin-knee contours for both the accelerator operating leg and the clutch operating leg for horizontally adjustable seats (see Figure 1). There is one contour for the clutch shin-knee and one contour for the accelerator shin-knee. There are three locating equations for each curve to accommodate male-to-female ratios of 50:50, 75:25, and 90:10 to 95:5.
CURRENT
2014-12-03
Standard
J1948_201412
This SAE Recommended Practice provides a standardized test procedure for heavy-duty truck sleeper berth restraints to determine whether they meet the FMCSR 393.76(h) requirements.
CURRENT
2014-12-03
Standard
J1522_201412
This SAE Recommended Practice describes two-dimensional 95th percentile truck driver side view, seated stomach contours for horizontally adjustable seats (see Figure 1). There is one contour and three locating lines to accommodate male-to-female ratios of 50:50, 75:25, and 90:10 to 95:5.
CURRENT
2014-12-01
Standard
AS5452B
This SAE Aerospace Standard (AS) will specify what type night vision goggles are required, minimum requirements for compatible crew station lighting, aircraft exterior lighting such as anticollision lights and position/navigation lights that are "NVG compatible." Also, this document is intended to set standards for NVG utilization for aircraft so that special use aircraft such as the Coast Guard, Border Patrol, Air Rescue, Police Department, Medivacs, etc., will be better equipped to chase drug smugglers and catch illegal immigrants, rescue people in distress, reduce high-speed chases through city streets by police, etc. Test programs and pilot operator programs are required. For those people designing or modifying civil aircraft to be NVG compatible, the documents listed in 2.1.3 are essential.
2014-11-24
WIP Standard
J2400
Forward Collision Warning (FCW) systems are onboard systems intended to provide alerts to assist drivers in avoiding striking the rear end of another moving or stationary motorized vehicle. This SAE Information Report describes elements for a FCW operator interface, as well as requirements and test methods for systems capable of warning drivers of rear-end collisions. This Information Report applies to original equipment and aftermarket FCW systems for passenger vehicles including cars, light trucks, and vans. This report does not apply to heavy trucks. Furthermore, this document does not address integration issues associated with adaptive cruise control (ACC), and consequently, aspects of the document could be inappropriate for an ACC system integrated with a FCW system.
2014-11-23
WIP Standard
AS8040C
This SAE Aerospace Standard (AS) covers combustion heaters used in the following applications: a. Cabin heating (all occupied regions and windshield heating) b. Wing and empennage anti-icing c. Engine and accessory heating (when heater is installed as part of the aircraft) d. Aircraft de-icing
CURRENT
2014-11-19
Standard
J782_201411
HISTORICAL
2014-11-13
Standard
AIR1059D
This document provides guidance concerning the maintenance and serviceability of oxygen cylinders beginning with the quality of oxygen that is required, supplemental oxygen information, handling and cleaning procedures, transfilling and marking of serviced oxygen assemblies. This document attempts to outline in a logical sequence oxygen quality, serviceability and maintenance of oxygen cylinders.
CURRENT
2014-10-30
Standard
AIR1133B
Solid chemical oxygen supplies of interest to aircraft operations are "chlorate candles" and potassium superoxide (KO2). Chlorate candles are used in passenger oxygen supply units and other emergency oxygen systems, such as submarines and escape devices. Potassium superoxide is not used in aircraft operations but is used in closed-cycle breathing apparatus. Characteristics and applications of both are discussed, with emphasis on chlorate candles.
Viewing 121 to 150 of 1265