Criteria

Text:
Content:
Display:

Results

Viewing 31 to 60 of 1253
CURRENT
2017-01-04
Standard
AS1303B
This SAE Aerospace Standard (AS) applies to a portable chemical oxygen generator assembly intended for the following uses: First aid treatment of aircraft occupants after an emergency descent following a decompression or other emergency condition. Use by cabin attendants to maintain their mobility after a decompression.
CURRENT
2017-01-03
Standard
ARP583J
This SAE Aerospace Recommended Practice (ARP) provides guidance for the design and location of cabin crew stations, including emergency equipment installations at or near such stations, so as to enable the cabin crew to function effectively in emergency situations, including emergency evacuations. Recommendations regarding design of cabin crew stations apply to all such stations; recommendations regarding location apply to those stations located near or adjacent to floor level exits.
CURRENT
2016-12-08
Standard
J3114_201612
The aim of this Information Report is to provide terms and definitions that are important for the user’s interaction with L2 through L4 driving automation system features per SAE J3016, which provides a basis for this document.
2016-12-07
WIP Standard
J983
This SAE Recommended Practice applies to mobile, construction type, crane and cable excavator hand and foot controls. It should not be construed to limit the use of, or to apply to combination controls, automatic controls, or any other special operating control requirements.
2016-11-18
WIP Standard
J100
This SAE Recommended Practice establishes boundaries for shade bands on glazed surfaces in class "A" vehicles. These boundaries are located so that the shade band can provide occupant comfort and driver vision protection from glare, with respect to solar radiation, under some lighting and driving conditions. Since shade bands transmit less visible light than adjacent glazed surfaces, the shade band boundaries establish boundaries for the driver's field of view.
CURRENT
2016-11-15
Standard
J1281_201611
This SAE Standard establishes the procedure for determining the operator duty cycle sound pressure level Lodc to which operators of powered recreational craft up to 24 m in length are exposed during typical operation as determined by marine engine duty cycle studies. This document describes the instrumentation, the required calibration procedures, the test site, the specifications for “standard craft”, the craft operating conditions, microphone positioning, test procedure, engine speeds for each of the Duty Cycle modes and the formula and table for calculating the Duty Cycle operator ear sound pressure level. This document is subject to change to keep pace with technical advances as well as other international standards and practices. Changes in this Revision: The sound pressure level measurements performed while applying this document are based on the Five-Mode Marine Engine Duty Cycle instead of a single engine speed.
CURRENT
2016-11-15
Standard
J100_201611
This SAE Recommended Practice establishes boundaries for shade bands on glazed surfaces in class "A" vehicles. These boundaries are located so that the shade band can provide occupant comfort and driver vision protection from glare, with respect to solar radiation, under some lighting and driving conditions. Since shade bands transmit less visible light than adjacent glazed surfaces, the shade band boundaries establish boundaries for the driver's field of view.
CURRENT
2016-11-07
Standard
J985_201611
The design and location of rear-viewing mirrors or systems, and the presentation of the rear view to the driver can best be achieved if the designer and the engineer have adequate references available on the physiological functions of head and eye movements and on the perceptual capabilities of the human visual system. The following information and charts are provided for this purpose. For more complete information of the relationship of vision to forward vision, see SAE SP-279.
CURRENT
2016-11-01
Standard
J3027_201611
This SAE Recommended Practice describes the testing procedures required to evaluate the integrity of a ground ambulance-based patient litter, litter retention system, and patient restraint when exposed to a frontal, side or rear impact. Its purpose is to provide litter manufacturers, ambulance builders, and end-users with testing procedures and, where appropriate, acceptance criteria that, to a great extent ensures the patient litter, litter retention system, and patient restraint utilizes a similar dynamic performance test methodology to that which is applied to other vehicle seating and occupant restraint systems. Descriptions of the test set-up, test instrumentation, photographic/video coverage, test fixture, and performance metrics are included.
2016-10-25
WIP Standard
J826/1
This document describes the CAD model data available from SAE for the HPM-1 three-dimensional H-point machine. The elements of the CAD model include the outer surfaces of the cushion and back pans, datum points and lines, and calibration references. The intended purpose for this information is to provide a CAD reference for design and benchmarking as well as a calibration reference for the physical HPM-1 audits. The content and format of the data files that are available are also described. The actual CAD model files are included with this product and are provided in the following formats: CATIA v4 (without parametrics), CATIA v5 (without parametrics), IGES, and STEP.
2016-10-21
WIP Standard
AIR1609B
This SAE Aerospace Information Report (AIR) covers the design parameters for various methods of humidification applicable to aircraft, the physiological aspects of low humidities, the possible benefits of controlling cabin humidity, the penalties associated with humidification, and the problems which must be solved for practical aircraft humidification systems. The design information is applicable to commercial and military aircraft. The physiological aspects cover all aircraft environmental control applications.
2016-10-03
WIP Standard
ARP4102/12B
This document specifies requirements for an Airborne Landing Guidance System (ALGS) electronic device. This equipment shall derive relative aircraft position and situation information for flight along precision three-dimensional paths within the appropriate coverage area. The precision three-dimensional path may be an ILS straight-in look-alike path or a complex, curved path. The requirements are applicable to electronic devices capable of receiving signals or other information from one or more sources, including but not limited to ILS, MLS, GNSS, or IRU inputs.
CURRENT
2016-09-30
Standard
J2678_201609
This document provides the rationale used by the Navigation Function Accessibility Subcommittee (the Subcommittee) for the development and content of a SAE J2364 Recommended Practice: Navigation and Route Guidance Function Accessibility While Driving. It provides both the reasoning for the overall recommended practice as well as each of its elements.
2016-09-28
WIP Standard
ARP4102/11D
This document recommends criteria for Airborne Windshear Systems, including operational objectives, characteristics and functional requirements. The recommendations of the document apply to transport aircraft, and describe the operational objectives of windshear alerting systems, situational displays, guidance systems and avoidance/detection systems.
2016-09-28
WIP Standard
ARP4102/5SECT3A
This document recommends design criteria for the flight deck installation of electrically signaled flight control systems on fixed wing airplanes.
2016-09-28
WIP Standard
ARP4102/5SECT1A
This document recommends design criteria for the flight deck installation of electrically signaled engine control systems.
2016-09-28
WIP Standard
ARP4102/13B
This document recommends criteria for a system designed to manage and communicate information via data link to support flight operations.
2016-09-27
WIP Standard
J283
The lift capacity can be determined by Section 4 and/or Section 5. When the results are recorded, the test method shall be identified.
2016-09-12
WIP Standard
J3126
This recommended practice provides technicians with safe and efficient techniques and general equipment recommendations for servicing Mobile Air Conditioning (MAC) systems in heavy duty and off-highway work machines. Presently, R-134a is the only approved refrigerant for use in mobile heavy duty and off-highway equipment and therefore this document primarily covers the servicing of R-134a systems. Since the technician may encounter other refrigerants a brief explanation on the identification safe handling of each refrigerant will be introduced.
2016-09-10
WIP Standard
AIR1811B
The purpose of this Aerospace Information Report (AIR) is to provide guidelines for the selection and design of airborne liquid cooling systems. This publication is applicable to liquid cooling systems of the closed loop type and the expendable coolant type in which the primary function is transporting of heat from its source to a heat sink. Most liquid cooling system applications are oriented toward the cooling of electronics. Liquid cooling techniques, heat sinks, design features, selection of coolants, corrosion control, and servicing requirements for these systems are presented. Information on vapor compression refrigeration systems, which are a type of cooling system, is found in Reference 1.
CURRENT
2016-08-23
Standard
J2956_201608
This SAE Recommended Practice describes the test procedures for conducting side impact occupant restraint and equipment mounting integrity tests for ambulance patient compartment applications. Its purpose is to describe crash pulse characteristics and establish recommended test procedures that will standardize restraint system and equipment mounting testing for ambulances. Descriptions of the test set-up, test instrumentation, photographic/video coverage, and the test fixtures are included.
CURRENT
2016-08-17
Standard
J2917_201608
This SAE Recommended Practice describes the test procedures for conducting frontal impact occupant restraint and equipment mounting integrity tests for ambulance patient compartment applications. Its purpose is to describe crash pulse characteristics and establish recommended test procedures that will standardize restraint system and equipment mounting testing for ambulances. Descriptions of the test set-up, test instrumentation, photographic/video coverage, and the test fixtures are included.
CURRENT
2016-08-17
Standard
J3044_201608
This SAE Recommended Practice describes the test procedures for conducting rear impact occupant restraint and equipment mounting integrity tests for ambulance patient compartment applications. Its purpose is to describe crash pulse characteristics and establish recommended test procedures that will standardize restraint system and equipment mount testing for ambulances. Descriptions of the test set-up, test instrumentation, photographic/video coverage, and the test fixtures are included.
2016-08-08
WIP Standard
AS6029B
This document provides guidance for laser operators and aviation authorities to determine the performance criteria that laser hazard control measures shall meet for the operation of an outdoor laser system in navigable airspace. The document does not cover systems intended to deliberately aim and or track lasers at aircraft such as FAA approved purposes, including visual warning systems, search and rescue, etc. Aircraft operations to be protected include all types that can be reasonably expected to operate in the affected area, which are traveling at speeds and altitudes defined in the Performance/Functional Requirements section. This document does not address all possible aircraft operations, (e.g., the operation of stealth, high-speed (> Mach 1), unmanned aircraft systems, aircraft above 60 000 feet MSL, etc.), including aircraft operating under a waiver from FAA regulations.
CURRENT
2016-08-02
Standard
J185_201608
Minimum criteria are provided for steps, stairways, ladders, walkways, platforms, handrails, handholds, guardrails, and entrance openings which permit ingress to and egress from operator, inspection, maintenance or service platforms on off-road work machines parked in accordance with the manufacturer's instructions.
CURRENT
2016-08-01
Standard
ARP6390
Various emergency situations may require the dispensing of oxygen to all occupants of aircraft during flight. During an emergency event, depending on the aircraft operational flight capability, all cabin occupants must be serviced by a mask presentation system connected to an operational oxygen source. Several regulations specify the functional characteristics and requirements of the oxygen systems for aircraft in support of different missions. These should be referred to for the exact functional performance requirements. It is not the intent of this document to ensure conformance with these regulations, but only to recommend general concepts for the location of the oxygen masks and oxygen system outlets for proper accessibility by the aircraft occupants, whether cabin occupants or crew members. Different requirements may apply when the mission of the pressurized aircraft or the operational altitude of the aircraft is not in excess of FL250.
CURRENT
2016-07-12
Standard
AIR6237
The scope of this document is to provide review of recent history of loss-of-control accidents during airline revenue operations.
CURRENT
2016-06-28
Standard
J2830_201606
This recommended practice describes a process for testing the comprehension of static (i.e., fixed or non-dynamic) symbols for all ground vehicles, for both OEM and aftermarket products. With advancing display technology, it is now possible to display dynamic symbols (e.g., a spinning beach ball to show that a process is ongoing, or a diagram showing energy distribution in hybrid vehicles). Such graphics are outside of the scope of this recommended practice, though extensions of this process may be useful for testing them. However, several symbols which occupy the same space on a display may change state without movement (e.g. play/pause button); these are within the scope of this recommended practice. The process described in this recommended practice includes criteria that are used to identify how well the perceived meaning matches the intended meaning for a representative sample of drivers.
2016-06-27
WIP Standard
AIR6319
This document describes how the program achieves its objective: to educate and train currently qualified commercial pilots with multi-engine and instrument ratings for First Officer and eventually Captain positions with the regional and/or the major airlines. This document provides an overview of a selection process, an academic curriculum, and a flight training program which will develop industry-recognized competencies and instill the knowledge, skills and attitudes known as professional standards.
CURRENT
2016-06-16
Standard
EIA441
This standard is intended to serve as a guide in the coordination of system design to promote uniformity of the nomenclature and description of the operator devices.
Viewing 31 to 60 of 1253