Criteria

Text:
Topic:
Content:
Display:

Results

Viewing 1 to 30 of 40
CURRENT
2017-03-17
Standard
J1455_201703
The scope of this Recommended Practice encompasses the range of environments which influence the performance and reliability of the electronic equipment designed for heavy duty on and off road vehicles, as well as any appropriate stationary applications which also use these vehicle derived components. A few examples of such vehicles are on and off highway trucks, trailers, buses, construction equipment, and agricultural equipment including implements.
CURRENT
2017-02-23
Standard
J1301_201702
The scope and purpose of this SAE Recommended Practice is to provide a classification system for deformation sustained by trucks involved in collisions on the highway. Application of the document is limited to medium trucks, heavy trucks, and articulated combinations.1 The TDC classifies collision contact deformation, as opposed to induced deformation, so that the deformation is segregated into rather narrow limits or categories. Studies of collision deformation can then be performed on one or many data banks with assurance that data under study are of essentially the same type.2 Many of the features of the SAE J224 MAR80 have been retained in this document, although the characters within specific columns vary. Each document must therefore be applied to the appropriate vehicle type. It is also important to note that the Truck Deformation Classification (TDC) does not identify specific vehicle configurations and body types.
CURRENT
2017-02-07
Standard
J2697_201702
This SAE Recommended Practice is intended to describe the application of single-phase DC to AC inverters, and bidirectional inverter/chargers, which supply power to ac loads in Class heavy duty on-highway trucks (10K GVW). The document identifies appropriate operating performance requirements and adds some insight into inverter selection. This document applies to factory and after-market installed DC-to-AC inverter systems (Including inverter chargers) providing up 3000 W of 120 VAC line-voltage power as a convenience for operator and passenger use. Such inverters are intended to power user loads not essential to vehicle Operation or safety (e.g., HVAC, TV, microwave ovens, battery chargers for mobile phones or laptop computers, audio equipment, etc.). Systems incorporate the inverter itself as well as the input, output, control, and signal wiring associated with the inverter.
CURRENT
2017-01-18
Standard
J2419_201701
This SAE Recommended Practice describes the test procedures for conducting frontal impact restraint system tests for heavy truck applications. Its purpose is to establish recommended test procedures that will standardize restraint system testing for heavy trucks. Descriptions of the test set-up, test instrumentation, photographic/video coverage, and the test fixtures are included.
CURRENT
2017-01-05
Standard
J1626/2_201701
This Recommended Practice provides a road test procedure for trucks and buses, to evaluate their compliance with Federal Motor Vehicle Safety Standard (FMVSS) 121; Air Brake Systems. Units of measure are English in lieu of metric to be consistent with FMVSS 121.
CURRENT
2016-09-13
Standard
J1708_201609
This SAE Recommended Practice defines a recommended practice for implementing a bidirectional, serial communication link among modules containing microcomputers. This document defines those parameters of the serial link that relate primarily to hardware and basic software compatibility such as interface requirements, system protocol, and message format. The actual data to be transmitted by particular modules, which is an important aspect of communications compatibility, is not specified in this document. These and other details of communication link implementation and use should be specified in the separate application documents referenced in Section 2.
CURRENT
2016-04-06
Standard
J2202_201604
This SAE Recommended Practice provides general guidelines on the material selection, construction and qualification of components and wiring systems used to construct wiring systems for Heavy Duty Vehicles The guidelines are limited to primary wiring systems of less than 50 V and includes cable sizes American Wire Gage 20 to AWG 4 on heavy-duty on-highway trucks. The document identifies appropriate operating performances requirements. This document excludes the male to female connection of the SAE J560 connectors.
CURRENT
2015-11-05
Standard
J1939/3_201511
SAE J1939-03 provides requirements and guidelines for the implementation of On Board Diagnostics (OBD) on heavy-duty vehicles (HDV) using the SAE J1939 family of standards. The guidelines identify where the necessary information to meet OBD regulations may be found among the SAE J1939 document set. Key requirements are identified here to insure the interoperability of OBD scan tools across individual OBD compliant vehicles. Market-defined regulations permit the use of SAE J1939 to meet OBD requirements. Implementers are cautioned to obtain and review the specific regulations for the markets where their products are sold. This document is focused on guidelines and requirements to satisfy the State of California Air Resources Board (ARB), the authors of 13 CCR 1971.1, United States Environmental Protection Agency, Euro IV and V requirements from European Commission directives, and UN/ECE WP 29 GRPE WWH OBD Global Technical Regulation (GTR).
CURRENT
2015-09-11
Standard
J2429_201509
This SAE Recommended Practice describes a test method for determination of heavy truck (Class VI, VII, and VIII) tire force and moment properties under free-rolling cornering conditions. The steady-state properties are acquired as functions of slip angle and normal force, which are changed incrementally using a sequence specified in this document. The data are suitable for use in vehicle dynamics modeling, comparative evaluations for research and development purposes, and manufacturing quality control. This document addresses two principal topics; a) the description of a hypothetical “Ideal Machine,” and b) a standard directly applicable to testing practices currently common to the industry. The references to the “Ideal Machine” are meant to provide a roadmap for the testing machine manufacturer, providing direction and goals for the next generation of testing capabilities.
CURRENT
2015-08-27
Standard
J2418_201508
This SAE Recommended Practice describes the test procedures for conducting frontal impact restraint tests for heavy truck applications. Its purpose is to establish recommended test procedures that will standardize restraint system testing for heavy trucks. Descriptions of the test set-up, test instrumentation, photographic/video coverage, and the test fixtures are included.
CURRENT
2015-06-04
Standard
J2426_201506
This SAE Recommended Practice describes the test procedures for conducting simulated dynamic lateral rollover restraint system tests for heavy truck applications. Its purpose is to establish recommended test procedures that will standardize restraint system testing for heavy trucks. Descriptions of the test set-up, test instrumentation, photographic/video coverage, and the test fixtures are included.
CURRENT
2014-11-18
Standard
J1214_201411
The purpose of this SAE Recommended Practice is set guidelines for tire to wheel house and body clearances on recreational vehicles.
CURRENT
2014-10-21
Standard
J3006_201410
This Recommended Practice is derived from OEM and tier-1 laboratory tests and applies to two-axle multipurpose passenger vehicles, or trucks with a GVWR above 4536 kg (10 000 pounds) equipped with hydraulic disc or drum service brakes. Before conducting testing for a specific brake sizes or under specific test conditions, review, agree upon, and document with the test requestor any deviations from the test procedure. Also, the applicable criteria for the final test results and wear rates deemed as significantly different require definition, assessment, and proper documentation; especially as this will determine whether or not Method B testing is needed. This Recommended Practice does not evaluate or quantify other brake system characteristics such as performance, noise, judder, ABS performance, or braking under extreme temperatures or speeds. Minimum performance requirements are not part of this recommended practice.
CURRENT
2014-06-02
Standard
J1853_201406
This SAE Standard includes spur gear and direct drive type hand-cranked winches as used on boat trailers. This does not include brake type winches as used in boat lift, davit, or industrial applications.
CURRENT
2014-05-30
Standard
J684_201405
This SAE Standard includes couplings, hitches, and safety chains used in conjunction with all types of trailers or towed vehicles whose Gross Vehicle Weight Rating (GVWR) does not exceed 4540 kg (10 000 lb). This includes such types as utility, boat, camping, travel, and special purpose trailers which are normally towed by conventional passenger cars, light-duty commercial vehicles, light trucks, and multipurpose passenger vehicles. This document is intended primarily for ball-and-socket type of couplings and hitches. It should not be construed as a limitation to this type alone but should apply where appropriate to ring-and-pintle, clevis-and-pin, or any other draft means designed to serve this purpose.
HISTORICAL
2008-10-03
Standard
J1853_200810
This SAE Standard includes spur gear and direct drive type hand-cranked winches as used on boat trailers. This does not include brake type winches as used in boat lift, davit, or industrial applications.
HISTORICAL
2006-06-26
Standard
J2664_200606
This SAE Information Report establishes a consistent procedure for measuring and analyzing the natural sway response of a particular trailer when attached to a particular vehicle under specific loading and operating conditions. This test procedure applies, but is not limited to, passenger cars, vans, light/medium-duty trucks as tow vehicles, and semitrailers with a Gross Vehicle Weight Rating (GVWR) of 11 794 kg (26 000 pounds) or less. Other applications include full trailers, tow dollies, tow bars, and the like. Other articulated vehicles can utilize this test procedure as long as the test does not exceed the linear behavior of the system. This test procedure does not apply to motorcycles towing trailers.
HISTORICAL
2005-07-27
Standard
J684_200507
This SAE Standard includes couplings, hitches, and safety chains used in conjunction with all types of trailers or towed vehicles whose Gross Vehicle Weight Rating (GVWR) does not exceed 4540 kg (10 000 lb). This includes such types as utility, boat, camping, travel, and special purpose trailers which are normally towed by conventional passenger cars, light-duty commercial vehicles, light trucks, and multipurpose passenger vehicles. This document is intended primarily for ball-and-socket type of couplings and hitches. It should not be construed as a limitation to this type alone but should apply where appropriate to ring-and-pintle, clevis-and-pin, or any other draft means designed to serve this purpose.
HISTORICAL
2004-06-21
Standard
J684_200406
This SAE Standard includes couplings, hitches, and safety chains used in conjunction with all types of trailers or towed vehicles whose Gross Vehicle Weight Rating (GVWR) does not exceed 4540 kg (10 000 lb). This includes such types as utility, boat, camping, travel, and special purpose trailers which are normally towed by conventional passenger cars, light-duty commercial vehicles, light trucks, and multipurpose passenger vehicles. This document is intended primarily for ball-and-socket type of couplings and hitches. It should not be construed as a limitation to this type alone but should apply where appropriate to ring-and-pintle, clevis-and-pin, or any other draft means designed to serve this purpose.
CURRENT
2003-10-20
Standard
J2638_200310
This document establishes minimum performance criteria and definition of terms for the towing interface between a towing vehicle and fifth wheel or gooseneck trailer at or below 13 608 kg (30 000 lb) gross trailer weight. This establishes criteria for the hitch, tow vehicle attachment structure, trailer attachment structure, and coupling.
HISTORICAL
2002-11-22
Standard
J1214_200211
The purpose of this SAE Recommended Practice is set guidelines for tire to wheel house and body clearances on recreational vehicles.
HISTORICAL
2000-06-28
Standard
J1853_200006
This SAE Standard includes spur gear and direct drive type hand-cranked winches as used on boat trailers. This does not include brake type winches as used in boat lift, davit, or industrial applications.
HISTORICAL
1998-06-01
Standard
J684_199806
This SAE Standard includes couplings, hitches, and safety chains used in conjunction with all types of trailers or towed vehicles whose Gross Vehicle Weight Rating (GVWR) does not exceed 4540 kg (10 000 lb). This includes such types as utility, boat, camping, travel, and special purpose trailers which are normally towed by conventional passenger cars, light-duty commercial vehicles, light trucks, and multipurpose passenger vehicles. This document is intended primarily for ball-and-socket type of couplings and hitches. It should not be construed as a limitation to this type alone but should apply where appropriate to ring-and-pintle, clevis-and-pin, or any other draft means designed to serve this purpose.
HISTORICAL
1997-04-01
Standard
J684_199704
This SAE Standard includes couplings, hitches, and safety chains used in conjunction with all types of trailers whose Gross Vehicle Weight Rating (GVWR) does not exceed 4540 kg (10,000 lb). This includes such types as utility, boat, camping, travel, and special purpose trailers which are normally towed by conventional passenger cars, light-duty commercial vehicles, light trucks, and multi-purpose passenger vehicles. This document is intended primarily for ball-and-socket type of couplings and hitches. It should not be construed as a limitation to this type alone but should apply where appropriate to ring-and-pintle, clevis-and-pin, or any other draft means designed to serve this purpose.
HISTORICAL
1994-03-01
Standard
J684_199403
This SAE Standard includes couplings, hitches, and safety chains used in conjunction with all types of trailers or towed vehicles whose Gross Vehicle Weight Rating (GVWR) does not exceed 4540 kg (10 000 lb). This includes such types as utility, boat, camping, travel, and special purpose trailers which are normally towed by conventional passenger cars, light-duty commercial vehicles, light trucks, and multipurpose passenger vehicles. This document is intended primarily for ball-and-socket type of couplings and hitches. It should not be construed as a limitation to this type alone but should apply where appropriate to ring-and-pintle, clevis-and-pin, or any other draft means designed to serve this purpose.
HISTORICAL
1992-01-01
Standard
J1214_199201
The purpose of this SAE Recommended Practice is set guidelines for tire to wheel house and body clearances on recreational vehicles.
HISTORICAL
1987-05-01
Standard
J684_198705
This SAE Standard includes couplings, hitches, and safety chains used in conjunction with all types of trailers or towed vehicles whose Gross Vehicle Weight Rating (GVWR) does not exceed 4540 kg (10 000 lb). This includes such types as utility, boat, camping, travel, and special purpose trailers which are normally towed by conventional passenger cars, light-duty commercial vehicles, light trucks, and multipurpose passenger vehicles. This document is intended primarily for ball-and-socket type of couplings and hitches. It should not be construed as a limitation to this type alone but should apply where appropriate to ring-and-pintle, clevis-and-pin, or any other draft means designed to serve this purpose.
HISTORICAL
1987-04-01
Standard
J1853_198704
This SAE Standard includes spur gear and direct drive type hand-cranked winches as used on boat trailers. This does not include brake type winches as used in boat lift, davit, or industrial applications.
HISTORICAL
1986-12-01
Standard
J1214_198612
The purpose of this SAE Recommended Practice is set guidelines for tire to wheel house and body clearances on recreational vehicles.
Viewing 1 to 30 of 40

Filter

  • Standard
    40