Criteria

Text:
Content:
Display:

Results

Viewing 1 to 30 of 183
CURRENT
2017-12-07
Standard
AMS4434N
This specification covers a magnesium alloy in the form of sand castings.
CURRENT
2017-12-07
Standard
AMS4958E
This specification covers a titanium alloy in the form of bars and rods 1.00 inch (25.4 mm) and under in nominal diameter.
CURRENT
2017-12-07
Standard
AMS5532H
This specification covers a corrosion and heat-resistant iron alloy in the form of sheet, strip, and plate.
CURRENT
2017-12-07
Standard
AMS5537J
This specification covers a corrosion and heat-resistant cobalt alloy in the form of sheet, strip, foil, and plate up to 2.250 inches (57.15 mm) inclusive, in nominal thickness (see 8.4).
CURRENT
2017-11-30
Standard
AMS4268A
This specification covers an aluminum alloy in the form of sheet and plate 0.010 to 1.500 inch (0.254 to 38.07 mm), inclusive, in thickness, supplied in the -T81/-T851 temper (see 8.5).
2017-11-17
WIP Standard
J452
The SAE Standards for aluminum casting alloys cover a wide range of castings for general and special use, but do not include all the alloys in commercial use. Over the years, aluminum alloys have been identified by many numbering systems as shown in Table 1. Presently, SAE is recommending the use of the UNS Numbering System to identify these materials. The castings are made principally by sand cast, permanent mold, or die cast methods; however, shell molding, investment casting, plaster cast, and other less common foundry methods may also be used. If the alloys listed do not have the desired characteristics, it is recommended that the manufacturers of aluminum castings be consulted.
2017-11-17
WIP Standard
J451
This information report is intended to give general data on the properties of aluminum and information on working, joining, forming, machining, finishing, and heat treating of aluminum.
2017-11-17
WIP Standard
J454
The SAE Standards for wrought aluminum alloys cover materials with a considerable range of properties and other characteristics, but do not include all of the commercially available materials. If none of the materials listed in Tables 1 through 7 provides the characteristics required by a particular application, users may find it helpful to consult with the suppliers of aluminum alloy products. See companion document, SAE J1434.
2017-11-17
WIP Standard
J415
(These definitions were prepared by the Joint Committee on Definitions of Terms Relating to Heat Treatment appointed by the American Society for Testing and Materials, The American Society for Metals, the American Foundrymen's Association, and the SAE.) This SAE revision emphasizes the terms used in heat treating ferrous alloys, but also includes for reference some non-ferrous definitions at the end of the document. This glossary is not intended to be a specification, and it should not be interpreted as such. Since this is intended to be strictly a set of definitions, temperatures have been omitted purposely.
2017-11-15
WIP Standard
J437
The information in this report covers data relating to SAE J438, Tool and Die Steels, and is intended as a guide to the selection for the steel best suited for the intended purpose and to provide recommended heat treatments and other data pertinent to their use. Specific requirements as to physical properties are not included because the majority of tool and die steels are either worked or given special heat treatments by the purchaser. The purchaser may or may not elect to use the accompanying data for specification purposes.
CURRENT
2017-11-13
Standard
AMS4269A
This specification covers an aluminum alloy in the form of sheet and plate supplied in the -T361 temper.
CURRENT
2017-11-13
Standard
AMS4475B
This specification covers an aluminum alloy in the form of alclad coiled sheet from 0.010 to 0.128 inches, incl (0.25 to 3.25 mm, incl) in thickness supplied in the –T4 temper (see 8.5).
CURRENT
2017-11-09
Standard
AMS5442B
This specification covers a corrosion and heat-resistant nickel alloy in the form of bars, forgings, and flash welded rings up to 5.0 inches (127mm) in least nominal cross-sectional dimension having a cross-sectional area not greater than 50 in2 (323 cm2), and stock of any size for forging or flash welded rings (see 8.5).
CURRENT
2017-11-09
Standard
AMS5596M
This specification covers a corrosion and heat-resistant nickel alloy in the form of sheet, strip, foil, and plate 1.00 inch (25.4 mm) and under in thickness (see 8.5).
CURRENT
2017-11-08
Standard
AMS4403A
This specification covers an aluminum alloy in the form of die forgings 1.000 to 12.000 inches inclusive (25 to 305 mm) in nominal thickness at the time of heat treatment and of forging stock (see 8.4).
CURRENT
2017-11-03
Standard
AMS4193D
This specification covers an aluminum alloy in the form of flat sheet and plate 0.500 inch (12.70 mm) and under in nominal thickness.
CURRENT
2017-10-18
Standard
AMS4337B
This specification covers an aluminum alloy in the form of extruded profiles (shapes) 0.500 to 1.500 inch, incl (12.7 to 38.1 mm, incl) in nominal thickness, and having a maximum cross-sectional area of 20 in2 (129 cm2) and a maximum circle size of 10 inches (254 mm) (see 8.7).
CURRENT
2017-10-13
Standard
AMS4296C
This specification covers an aluminum alloy in the form of sheet and plate 0.032 to 0.310 inch, incl (0.81 to 7.87 mm, incl) in thickness, clad on both sides (see 8.4).
CURRENT
2017-10-13
Standard
AMS4463A
This specification covers an aluminum alloy in the form of plate 0.750 to 1.500 inch, incl ( 19.05 to 38.10 mm, incl) in thickness (see 8.5).
CURRENT
2017-10-10
Standard
AMS4206C
This specification covers an aluminum alloy in the form of plate 0.500 to 1.500 inches (12.70 to 38.10 mm) inclusive, in thickness (see 8.4).
CURRENT
2017-10-10
Standard
AMS4329B
This specification covers an aluminum alloy in the form of plate 4.001 to 7.000 inch, incl. (101.62 to 177.80 mm, incl.) in thickness (see 8.4).
CURRENT
2017-10-10
Standard
AMS4464A
This specification covers an aluminum alloy in the form of plate 0.500 to 1.500 inch, incl (12.70 to 38.10 mm, incl) in thickness (see 8.4).
CURRENT
2017-10-10
Standard
AMS4467B
This specification covers an aluminum alloy in the form of alclad sheet and plate supplied in the -T861 temper.
2017-09-27
WIP Standard
AMS3025E
This specification covers two types of polyalkylene glycol in the form of a liquid.
CURRENT
2017-09-22
Standard
AMS6327L
This specification covers an aircraft-quality, low-alloy steel in the form of bars and forgings.
CURRENT
2017-09-18
Standard
AMS4981H
This specification covers a titanium alloy in the form of bars, wire, and forgings up through 4.000 inches (101.60 mm), inclusive, in diameter or least distance between parallel sides and forging stock of any size (see 8.6).
CURRENT
2017-09-14
Standard
AMS5337E
This specification covers an alloy steel in the form of investment castings.
CURRENT
2017-09-13
Standard
AMS4466A
This specification covers an aluminum alloy in the form of alclad sheet and plate 0.020 to 0.500 inch (0.508 to 12.70 mm) inclusive, in thickness, supplied in the -T361 temper (see 8.5).
CURRENT
2017-09-13
Standard
AMS4163F
This specification covers an aluminum alloy in the form of extruded bars, rods, wire, profiles, and tubing up to 2.999 inches, incl (76.17 mm, incl) in thickness, nominal diameter or wall thickness with cross-sectional area 25 in2 (161 cm2) and under (see 8.5).
CURRENT
2017-09-11
Standard
AMS4251B
This specification covers an aluminum alloy in the form of sheet 0.040 to 0.249 inch (1.02 to 6.32 mm) in thickness (see 8.6).
Viewing 1 to 30 of 183

Filter

  • Standard
    183