Criteria

Text:
Content:
Display:

Results

Viewing 1 to 30 of 322
2017-04-10
WIP Standard
J1752/3
This measurement procedure defines a method for measuring the electromagnetic radiation from an integrated circuit (IC). The IC being evaluated is mounted on an IC test printed circuit board (PCB) that is clamped to a mating port (referred to as a wall port) cut in the top or bottom of a TEM or wideband TEM (GTEM) cell. The test board is not in the cell as in the conventional usage but becomes a part of the cell wall. This method is applicable to any TEM or GTEM cell modified to incorporate the wall port; however, the measured RF voltage is affected by the septum to test board (wall) spacing. This procedure was developed using a 1 GHz TEM cell with a septum to wall spacing of 45 mm and a GTEM cell with average septum to wall spacing of 45 mm over the port area. Other cells may not produce identical spectral output but may be used for comparative measurements, subject to their frequency and sensitivity limitations.
CURRENT
2017-03-02
Standard
J3108_201703
This recommended practice prescribes clear and consistent labeling methodology for communicating important xEV high voltage safety information. Examples of such information include identifying key high voltage system component locations and high voltage disabling points. These recommendations are based on current industry best practices identified by the responder community. Although this recommended practice is written for xEVs with high voltage systems, these recommendations can be applied to any vehicle type.
CURRENT
2017-02-02
Standard
ARP577E
This SAE Aerospace Recommended Practice (ARP) specifies criteria for the design, development, standardization, and comprehension testing of placards containing pictures, drawings, symbols, and/or written instructions for locating and operating aircraft emergency equipment. This ARP also provides guidance in the selection and implementation of warning placards intended to instruct occupants inside, and rescue personnel outside, the aircraft.
CURRENT
2017-01-04
Standard
ARP6239
This SAE Aerospace Recommended Practice (ARP) recommends the design and features of aircraft demonstration emergency equipment for use in passenger safety briefings.
CURRENT
2017-01-03
Standard
ARP583J
This SAE Aerospace Recommended Practice (ARP) provides guidance for the design and location of cabin crew stations, including emergency equipment installations at or near such stations, so as to enable the cabin crew to function effectively in emergency situations, including emergency evacuations. Recommendations regarding design of cabin crew stations apply to all such stations; recommendations regarding location apply to those stations located near or adjacent to floor level exits.
2016-11-23
WIP Standard
AS407E
To specify minimum requirements for Fuel Flowmeters for use primarily in reciprocating engine powered civil transport aircraft, the operation of which may subject the instruments to the environmental conditions specified in Section 3.3. This Aeronautical Standard covers two basic types of instruments, or combinations thereof, intended for use in indicating fuel consumption of aircraft engines as follows: TYPE I - Measure rate of flow of fuel used. TYPE II - Totalize amount of fuel consumed or remaining.
CURRENT
2016-11-10
Standard
AMS3827C
This specification covers a style 7781 glass cloth impregnated with a heat-curable polyester resin system, the resin being processed to a "B" stage condition, and furnished in the form of continuous rolls.
CURRENT
2016-09-16
Standard
J1981_201609
The test is designed to evaluate the frontal impact resistance of wheel and tire assemblies used with passenger cars, light trucks and multi-purpose vehicles. The test is specifically related to vehicle pothole tests that are undertaken by most vehicle manufacturers. The scope has been expanded to allow the use of a striker that can be angled to preferentially impact the inboard and outboard wheel flange. For side impact of the outboard rim flange only, please refer to SAE J175. This SAE Recommended Practice provides a procedure to test a wheel or a tire and the test failure criteria. The specific test for a vehicle requires input from a pothole test on that vehicle to establish the drop height of the striker used in this test.
CURRENT
2016-07-12
Standard
AMS3779B
This specification and its supplementary detail specifications cover thermal radiation resistant materials in the form of tape with pressure-sensitive adhesive.
CURRENT
2016-07-12
Standard
AMS3779/2B
This specification covers thermal radiation resistant material in the form of tape with pressure-sensitive adhesive.
CURRENT
2016-07-12
Standard
AMS3779/1B
This specification covers thermal radiation resistant material in the form of tape with pressure-sensitive adhesive.
CURRENT
2016-06-03
Standard
J2990/1_201606
Electric and alternative fueled vehicles present different hazards for first and second responders than conventional gasoline internal combustion engines. Hydrogen vehicles (H2V) including Fuel Cell Vehicles (FCVs) involved in incidents may present unique hazards associated with the fuel storage and high voltage systems. The electrical hazards associated with the high voltage systems of hybrid-electric vehicles and FCVs are already addressed in the parent document, SAE J2990. This Recommended Practice therefore addresses electric issues by reference to SAE J2990 and supplements SAE J2990 to address the potential consequences associated with hydrogen vehicle incidents and suggest common procedures to help protect emergency responders, tow and/or recovery, storage, repair, and salvage personnel after an incident has occurred. Industry design standards and tools were studied and where appropriate, suggested for responsible organizations to implement.
CURRENT
2016-05-24
Standard
ARP594E
The requirements presented in this document cover the design factors which might cause any part of an electrically motor driven fuel pump assembly to act as an ignition source for explosive fuel vapors within the airplane tank.
2016-05-19
WIP Standard
AS1426C
This specification is intended to be used as a general standard for industry use for design and construction of air transport galley equipment and inflight food service systems.
CURRENT
2015-12-06
Standard
ARP4712A
This SAE Aerospace Recommended Practice (ARP) establishes general criteria for the installation (e.g., type, location, accessibility, stowage) and crew member training needed for hand-held fire extinguishers.
CURRENT
2015-12-04
Standard
ARP503G
This SAE Aerospace Recommended Practice (ARP) provides criteria for design and location of power supplies, controls, light fixtures, and associated equipment which are used to provide emergency illumination in transport aircraft, designed to comply with 14 CFR part 25 (Reference 1) for operation under 14 CFR part 91 (Reference 11) and 14 CFR part 121 (Reference 2), and also in compliance with FAA Advisory Circulars AC25.812-1A (Reference 3) and AC25.812-2 (Reference 10). It is not the purpose of an ARP to specify design methods to be followed in the accomplishment of the stated objectives.
CURRENT
2015-09-07
Standard
ARP5533A
This SAE Aerospace Recommended Practice (ARP) covers the requirements for a Stationary Runway Weather Information System (referred to as the system) to monitor the surface conditions of airfield operational areas to ensure safer ground operations of aircraft. The system provides (1) temperature and condition information of runway, taxiway, and ramp pavements and (2) atmospheric weather conditions that assist airport personnel to maintain safer and more efficient airport operations. The system can be either a wired system or a wireless system.
CURRENT
2015-08-28
Standard
AIR6185
This SAE Aerospace Information Report (AIR) describes hydraulic system design and installation to minimize the effects of lightning, especially when the aircraft structure is composite. Techniques for effective electrical bonding, hydraulic system lightning protection, and lightning protection verification techniques are discussed.
CURRENT
2015-05-07
Standard
J2980_201505
This SAE Recommended Practice presents a method and example results for determining the Automotive Safety Integrity Level (ASIL) for automotive electrical and electronic (E/E) systems. This activity is required by ISO 26262-3:2011 [1], and it is intended that the process and results herein are consistent with ISO 26262:2011 [1]. The technical focus of this document is on vehicle motion control systems. It is limited to passenger cars weighing up to 3.5 metric tons. Furthermore, the scope of this recommended practice is limited to collision-related hazards. ISO 26262:2011 [1] has a wider scope than SAE J2980, covering other functions and accidents (not just motion control or collisions as in SAE J2980).
CURRENT
2015-01-20
Standard
J1212_201501
This document applies to off-road forestry work machines defined in SAE J1116 or ISO 6814.
CURRENT
2014-11-25
Standard
AS245C
This specification covers the following types and classes of extinguishers: Type I Stored pressure type Category A - Operational Temperature range −40 to +140 °F (−40 to +60 °C) Category B - Operational Temperature range +35 to +140 °F (+1.7 to +60 °C) Type II Cartridge operated type Category A - Operational Temperature range −40 to +140 °F (−40 to +60 °C) Category B - Operational Temperature range +35 to +140 °F (+1.7 to +60 °C)
CURRENT
2014-10-16
Standard
AIR1169C
The scope of this document is to provide a list of documents of types pertaining to the effects of oxygen on ignition and combustion of materials. Consolidating these references in one place makes it easier to find documents of this type as these references are difficult to locate.
CURRENT
2014-09-05
Standard
ARP5548
This equipment specification covers requirements for Multi-Tasking Equipment (MTE) for airfield snow removal purposes. The unit shall include a combination of a carrier vehicle, snow plow, rotary broom and high velocity air blast system. This vehicle as a unit shall be an integrated snow plow, rotary broom and high velocity air blast. Primary application is for the high-speed plowing, sweeping and cleaning of ice and snow from airfield operational areas such as runways, taxiways and ramp aprons. The term carrier vehicle represents the various self-propelled prime movers that provide the motive power necessary to move snow and ice control equipment during winter operations. The airport operator may require this specified piece of equipment in order to maintain the airfield during large and small snow events. When necessary, the MTE shall be a central and critical element in the winter pavement maintenance fleet in the effort to accomplish the airport’s published snow plan.
CURRENT
2014-08-14
Standard
J3024_201408
This document presents a catalog of safety sign text and artwork that can be used by any ready mixed concrete truck manufacturer to warn of common hazards.
CURRENT
2014-06-20
Standard
ARP8058
This SAE Aerospace Recommended Practice (ARP) provides design guidance and a method for testing thermal performance of airplane in-flight food storage carts. It is noted that thermal performance criteria is not part of AS8056.
2014-06-11
WIP Standard
ARP5414B
This SAE Aerospace Recommended Practice (ARP) defines lightning strike zones and provides guidelines for locating them on particular aircraft, together with examples. The zone definitions and location guidelines described herein are applicable to Parts 23, 25, 27, and 29 aircraft. The zone location guidelines and examples are representative of in-flight lightning exposures.
2014-06-09
WIP Standard
ARP6331
This document recommends contents for Emergency Medical Kits, including medications and instrumentation, intended for use on passenger-carrying aircraft serviced by at least 1 flight attendant. Recommended practices for carriage of, access to, and maintenance of Emergency Medical Kits are also included.
CURRENT
2014-04-14
Standard
ARP5446A
These recommendations are provided to aid the international air transport industry by identifying a standard, minimum amount of safety instructions that should be given to sight-impaired passengers. This document is not meant to address problems associated with communicating safety information to sight-impaired passengers who are also hearing impaired or non-conversant in the language(s) used by the cabin crew to disseminate general safety information to passengers. Aircraft operators are encouraged to customize the safety instructions for their own operations in order to ensure that required safety information is provided to sight-impaired passengers.
CURRENT
2013-12-17
Standard
AS8036A
This SAE Aerospace Standard (AS) specifies minimum performance standards for the following types of fire detection instruments intended for use in protecting aircraft cargo compartments, galleys, electronic equipment bays and other similar installations.
CURRENT
2013-10-10
Standard
ARP1315E
This SAE Aerospace Recommended Practice (ARP) establishes safety recommendations for lavatories in transport category airplanes.
Viewing 1 to 30 of 322

Filter