Criteria

Display:

Results

Viewing 1 to 30 of 14423
2017-11-15
Journal Article
2017-32-0119
Akira Iijima, Takuya Izako, Takahiro Ishikawa, Takahiro Yamashita, Shuhei Takahata, Hiroki Kudo, Kento Shimizu, Mitsuaki Tanabe, Hideo Shoji
Engine knock is the one of the main issues to be addressed in developing high-efficiency spark-ignition (SI) engines. In order to improve the thermal efficiency of SI engines, it is necessary to develop effective means of suppressing knock. For that purpose, it is necessary to clarify the mechanism generating pressure waves in the end-gas region. This study examined the mechanism producing pressure waves in the end-gas autoignition process during SI engine knock by using an optically accessible engine. Occurrence of local autoignition and its development process to the generation of pressures waves were analyzed under several levels of knock intensity. The results made the following points clear. It was observed that end-gas autoignition seemingly progressed in a manner resembling propagation due to the temperature distribution that naturally formed in the combustion chamber. Stronger knock tended to occur as the apparent propagation speed of autoignition increased.
2017-11-15
Journal Article
2017-32-0120
Go Asai, Yusuke Watanabe, Shuntaro Ishiguro, Gen Shibata, Hideyuki Ogawa, Yoshimitsu Kobashi
To extend the operational range of premixed diesel combustion, fuel reformation by piston induced compression of rich homogeneous air-fuel mixtures was conducted in this study. Reformed gas compositions and chemical processes were first simulated with the chemistry dynamics simulation, CHEMKIN Pro, by changing the intake oxygen content, intake air temperature, and compression ratio. A single cylinder diesel engine was utilized to verify the simulation results. With the simulation and experiments, the characteristics of the reformed gas with respect to the reformer cylinder operating condition were obtained. Further, the thermal decomposition and partial oxidation reaction mechanisms of the fuel in extremely low oxygen concentrations were obtained with the characteristics of the gas production at the various reaction temperatures.
2017-10-13
Technical Paper
2017-01-5014
Maurilio Pereira Gomes, Igor Santos, Camila Couto, Cristiano Mucsi, Jesualdo Luiz Rossi, Marco Colosio
Abstract This work consists of evaluating the influence of heat treatment on sintered valve seat insert (VSI) obtained with two different high-speed steels powders and one tool steel: AISI M3:2, AISI M2 and AISI D2, respectively. The high-speed / tool steel powders were mixed with iron powders and additives such as manganese sulphide, zinc stearate, graphite and niobium carbide. All the high-speed / tool steel powders had its particle size distribution and morphology analyzed. The heat treatment of the VSI consisted of air quenching followed by double tempering it in seven different and equidistant temperatures, ranging from 100 °C until 700 °C. A data acquisition system with a thermocouple type k attached to the samples was used to determine the air-quenching cooling rate. The mechanical and physical properties measurements were carried out, i.e., apparent density, apparent hardness and crush radial strength.
2017-10-08
Technical Paper
2017-01-2340
Shashank Mishra, Anand Krishnasamy
Abstract Biodiesel is a renewable, carbon neutral alternative fuel to diesel for compression ignition engine applications. Biodiesel could be produced from a large variety of feedstocks including vegetable oils, animal fats, algae, etc. and thus, vary significantly in their composition, fuel properties and thereby, engine characteristics. In the present work, the effects of biodiesel compositional variations on engine characteristics are captured using a multi-linear regression model incorporated with two new biodiesel composition based parameters, viz. straight chain saturation factor (SCSF) and modified degree of unsaturation (DUm). For this purpose, biodiesel produced from seven vegetable oils having significantly different compositions are tested in a single cylinder diesel engine at varying loads and injection timings. The regression model is formulated using 35 measured data points and is validated with 15 other data points which are not used for formulation.
2017-10-08
Technical Paper
2017-01-2339
Pi-qiang Tan, Yuan Li
Abstract With increasingly severe atmospheric environmental problems, diesel car emissions have attracted broad attention for its main contribution to air pollutant. Alternative fuels become a hot research point in vehicle for rapidly consuming of fossil oil resources. Biodiesel and GTL (gas to liquid) fuels are two typical alternative fuels for diesel fuel. Low blend ratio (≤10%) biodiesel and GTL fuels can be used in a diesel engine without modifying the engine’s configuration. It is important to investigate the difference of low blend ratio biodiesel and GTL fuels used in the same diesel car and to find the optimum one. Gaseous and particle emissions from a light duty diesel car with B10 (10% biodiesel from cooking oil +90% diesel, v/v) and G10 (10% GTL fuel +90% diesel, v/v) was investigated. It was equipped with high pressure common rail system, cooled EGR and DOC and was tested on a chassis dynamometer under NEDC mode.
2017-10-08
Technical Paper
2017-01-2327
Joonsik Hwang, Choongsik Bae, Chetankumar Patel, Avinash Kumar Agarwal, Tarun Gupta
Abstract Fuel atomization and air-fuel mixing processes play a dominant role on engine performance and emission characteristics in a direct injection compression ignition engine. Understanding of microscopic spray characteristics is essential to predict combustion phenomena. The present work investigated near nozzle flow and atomization characteristics of biodiesel fuels in a constant volume chamber. Waste cooking oil, Jatropha, and Karanja biodiesels were applied and the results were compared with those of conventional diesel fuel. The tested fuels were injected by a solenoid injector with a common-rail injection system. A high-speed camera with a long distance microscopic lens was utilized to capture the near nozzle flow. Meanwhile, Sauter mean diameter (SMD) was measured by a phase Doppler particle analyzer to compare atomization characteristics.
2017-10-08
Technical Paper
2017-01-2326
Ang Li, Zhiwei Deng, Lei Zhu, Zhen Huang
Abstract In the present study a novel surrogate model for biodiesel including methyl decanoate (MD) and methyl crotonate (MC) was proposed and validated. In the binary mixture of surrogate fuel, MD was chosen to represent saturated methyl esters, which exhibited great low-temperature reactivity with typical negative temperature-coefficient (NTC) behavior and MC represented unsaturated components in real biodiesel, which was mainly responsible for soot formation and evolution. The proportion of MD and MC was determined by matching the characteristics such as derived cetane number (DCN), molecular weight (MW), atom number, H/C ratio and unsaturated degree. All of the criterions were calculated by the least square principles and the calculated surrogate of biodiesel was comprised of 92% MD and 8% MC in mole fraction. Furthermore, detailed kinetic model of the surrogate fuel was constructed and developed with modifications, which was composed of 2918 species and 9164 reactions.
2017-10-08
Technical Paper
2017-01-2328
Yuanxu Li, Karthik Nithyanandan, Zhi Ning, Chia-Fon Lee, Han Wu
Abstract Bio-butanol has been widely investigated as a promising alternative fuel. However, the main issues preventing the industrial-scale production of butanol is its relatively low production efficiency and high cost of production. Acetone-butanol-ethanol (ABE), the intermediate product in the ABE fermentation process for producing bio-butanol, has attracted a lot of interest as an alternative fuel because it not only preserves the advantages of oxygenated fuels, but also lowers the cost of fuel recovery for individual component during fermentation. If ABE could be directly used for clean combustion, the separation costs would be eliminated which save an enormous amount of time and money in the production chain of bio-butanol.
2017-10-08
Technical Paper
2017-01-2329
Xiao Ma, Yue Ma, Shuaishuai Sun, Shi-Jin Shuai, Zhi Wang, Jian-Xin Wang
Abstract Polyoxymethylene dimethyl ethers (PODEn) are promising alternative fuel candidates for diesel engines because they present advantages in soot reduction. This study uses a PODEn mixture (contains PODE3-6) from mass production to provide oxygen component in blend fuels. The spray combustion of PODEn-diesel bend fuels in a constant volume vessel was studied using high speed imaging, PLII-LEM and OH* chemiluminescence. Fuels of several blend ratios are compared with pure diesel. Flame luminance data show a near linear decrease tendency with the blend ratio increasing. The OH* images reveal that the ignition positions of all the cases have small differences, which indicates that using a low PODEn blend ratio of no more than 30% does not need significant adjustment in engine combustion control strategies. It is found that 30% PODEn blended with diesel (P30) can effectively reduce the total soot by approximately 68% in comparison with pure diesel.
2017-10-08
Technical Paper
2017-01-2331
Amar Deep, Naveen Kumar, Harveer Singh Pali
Abstract The use of alternative fuel has many advantages and the main ones are its renewability, biodegradability with better quality exhaust gas emission, which do not contribute to raise the level of carbon dioxide in the atmosphere. The use of non-edible vegetables oils as an alternative fuels for diesel engine is accelerated by the energy crisis due to depletion of resources and increase in environmental problems. In Asian countries like India, great need of edible oil as a food so cannot use these oils as alternative fuels for diesel engine. However there are many issues related to the use of vegetable oils in diesel engine that is high viscosity, low calorific value, high self-ignition temperature etc. Jatropha curcas has been promoted in India as a sustainable substitute to diesel fuel. This research prepared micro emulsions of ethanol and Jatropha vegetable oil in different ratio and find out the physico-chemical parameters to compare with mineral diesel oil.
2017-10-08
Technical Paper
2017-01-2330
Leonardo Israel Farfan-Cabrera, Ezequiel Gallardo, José Pérez-González
Abstract Flouroelastomers and silicone rubbers are commonly employed in static and dynamic seals for automotive applications. In order to prevent premature failures and leakages caused by swelling and/or changes in their mechanical properties, materials for seals are selected according to their compatibility with the environment and fluids involved in the engine operation. Thus, in particular, the use of new fuels and additives in automotive engines requires the assessment of compatibility with common sealing elastomers to prevent failures. Currently, Jatropha oil is being used as a renewable source of fuel in diesel engines for electricity production, transport or agricultural mechanization in various countries. It is used either as biodiesel or as straight vegetable oil (SVO) since it has good heating power and provide exhaust gas with almost no sulfur or aromatic polycyclic compounds. However, the compatibility of elastomers with this SVO has not been investigated yet.
2017-10-08
Technical Paper
2017-01-2333
Marcos Gutierrez, Andres Castillo, Juan Iniguez, Gorky Reyes
Abstract Aiming for cleaner and more efficient energy from the internal combustion engines makes necessary to ensure the special conditions for exploitation of alternative fuels. The engine vibrations are primarily understood as effects of mechanical failures, but they are also a subject of the fuel combustion effects. These effects depend on the fuel type and its ability to complete the combustion process. The vibrations of a diesel engine were measured and analyzed with a frequency spectrum calculated with fast Fourier transforms. The engine was operated with a fuel blend of 10 % recycled lubricating oil with 90% diesel fuel as well as with neat diesel. It was found that the engine operation with this fuel blend has a lower vibration level in comparison with the use of neat diesel fuel. The goal of this research is to determine the properties of the fuel blend, which provide more stability to the engine by means of vibrations reduction.
2017-10-08
Technical Paper
2017-01-2332
Tamara Ottenwaelder, Stefan Pischinger
Abstract In order to reduce engine out CO2 emissions it is a main subject to find new alternative fuels out of renewable sources. For this paper, several fuels were selected which can be produced out of biomass or with hydrogen which is generated directly via electrolysis with electricity from renewable sources. All fuels are compared to conventional diesel fuel and two diesel surrogates. It is well known that there can be a large effect of fuel properties on mixture formation and combustion, which may result in a completely different engine performance compared to the operation with conventional diesel fuels. Mixture formation and ignition behavior can also largely affect the pollutant formation. The knowledge of the combustion behavior is also important to design new engine geometries or implement new calibrations for an existing engine. The fuel properties of the investigated fuels comprise a large range, for example in case of the derived cetane number, from below 30 up to 100.
2017-10-08
Technical Paper
2017-01-2352
Gongde Liu, Li Wang, Runxiang Zhang, Chao Yang, Tengfei Shao
Abstract Fuel economy, Emission regulation and extended oil drain intervals (ODI) are the three key driving forces for engine oil development. More and more attentions have been focused on long ODI diesel engine oil both from the domestic OEMs and oil suppliers, and the ODI was being periodically improved from a normal mileage of about 1×104 kilometers to 6/8/10×104 km or even 12×104 km just within several years on China market. Lots and lots of factors may affect the oil life including oil properties, engine technologies, after-treatment devices and engine working conditions and so on. While from the oil side, the main factors contribute to the oil drain intervals may be the oil nitration and oxidation, soot contamination, base number deterioration and sludge accumulation and etc. There are two strategies to extend the oil longevity applied currently.
2017-10-08
Technical Paper
2017-01-2357
Mark Devlin, Jeffrey Guevremont, Chip Hewette, Marc Ingram, Grant Pollard, William Wyatt
Abstract Different mechanical components in a vehicle can be made from different steel alloys with various surface treatments or coatings. Lubricant technology is needed to prevent wear and control friction on all of these different surfaces. Phosphorus compounds are the key additives that are used to control wear and they do this by forming tribofilms on surfaces. It has been shown that different operating conditions (pressures and sliding conditions) can influence the formation of tribofilms formed by different anti-wear additives. The effect of surface metallurgy and morphology on tribofilm formation is described in this paper. Our results show that additive technology can form proper tribofilms on various surfaces and the right combination of additives can be found for current and future surfaces.
2017-10-08
Technical Paper
2017-01-2359
Yaodong Hu, Fuyuan Yang, Minggao Ouyang
Abstract Energy saving is becoming one of the most important issues for the next generation of commercial vehicles. The fuel consumption limits for commercial vehicles in China have stepped into the third stage, which is a great challenge for heavy duty commercial vehicles. Hybrid technology provides a promising method to solve this problem, of which the dual motor coaxial series parallel configuration is one of the best options. Compared with parallel configuration, the powertrain can not only operate in pure electric or parallel mode, but also can operate in series mode, which shows better flexibility. In this paper, regulations on test cycle, fuel consumption limits and calculation method of the third stage will be introduced in detail. Then, the quasi-static models of the coaxial series parallel powertrain with/without gearbox under C-WTVC (China worldwide transient vehicle cycle) are built. The control strategies are designed based on engine and motor performance.
2017-10-08
Technical Paper
2017-01-2350
Chalermwut Wongtaewan, Umaporn Wongjareonpanit, Komkrit Sivara, Ken Hashimoto, Yoichiro Nakamura
Abstract In Thailand, most heavy-duty trucks were equipped with diesel engine, while a small portion was equipped with compressed natural gas (CNG) engine. However, in the past few years the number of CNG fuel trucks in Thailand has increased significantly due to the cheaper cost of CNG. In general, the emphasis of heavy-duty diesel engine oil performance is on piston cleanliness and soot handling properties, while thermal and anti-oxidation properties are most critical for CNG engine oil performance. For truck fleet owners who operate both types of trucks, using the inappropriate oil that is not fit-for-purpose can adversely affect engine performance and reduce engine service lifespan under prolonged usage. A novel CNG/diesel engine oil was developed to meet both JASO DH-2 heavy-duty diesel engine oil performance and CNG engine oil performance. The candidate formulation was proved adequately fit for practical use regarding to thermal and anti-oxidation properties.
2017-10-08
Technical Paper
2017-01-2369
Prakash Arunachalam, Martin Tuner, Per Tunestal, Marcus Thern
Abstract Humid air motor (HAM) is an engine operated with humidified inlet charge. System simulations study on HAM showed the waste heat recovery potential over a conventional system. An HAM setup was constructed, to comprehend the potential benefits in real-time, the HAM setup was built around a 13-litre six cylinder Volvo diesel engine. The HAM engine process is explained in detail in this paper. Emission analysis is also performed for all three modes of operation. The experiments were carried out at part load operating point of the engine to understand the effects of humidified charge on combustion, efficiency, and emissions. Experiments were conducted without EGR, with EGR, and with humidified inlet charge. These three modes of operation provided the potential benefits of each system. Exhaust heat was used for partial humidification process. Results show that HAM operation, without compromising on efficiency, reduces NOx and soot significantly over the engine operated without EGR.
2017-10-08
Technical Paper
2017-01-2361
David R. Lancaster
Abstract Virtually all developed countries regulate light-duty vehicle emissions and fuel consumption. Those regulations rely on different procedures and driving cycles in testing to different standards in different countries. As a result, it is often very difficult to compare the standards imposed by different countries. This paper utilizes publicly available data to compare the energy requirements of the chassis dynamometer driving cycles in common use throughout the world. It also examines the relative severity of the currently existing light duty vehicle CO2 standards, some of which are mass-based with a targeted fleet average, and some of which are individual vehicle targets based on footprint.
2017-10-08
Technical Paper
2017-01-2397
Zhan Gao, Lei Zhu, Xinyao Zou, Chunpeng Liu, Zhen Huang
Abstract Biodiesel is a potential alternative fuel which can meet the growing need for sustainable energy. Partially premixed compression ignition (PPCI) is an important low-temperature combustion strategy to reduce NOx and soot emission of diesel engines. To investigate partial premixing impact on particle formation in flames of biodiesel or biodiesel surrogates, an experimental study was performed to compare the soot morphology and nanostructure evolution in laminar co-flow methyl decanoate non-premixed flame (NPF) and partially premixed flame (PPF). The thermophoretic sampling technique was used to capture particles along flame centerlines. Soot morphology information and volume fraction were obtained from TEM analysis and nanostructure features were evaluated by HR-TEM. With primary equivalence ratio of 19, gas temperature of PPF is higher along flame centerline compared with NPF. The results show an initially stronger sooting tendency in PPF at lower positions.
2017-10-08
Technical Paper
2017-01-2396
Fushui Liu, Yang Hua, Han Wu, Xu He, Ning Kang
Abstract Soot emission, known as PM (particulate matter), is becoming a big issue for GDI engines as the emission regulations being increasingly stricter. It is found that ethanol, as an oxygenated bio-fuel, can reduce the soot emission when added to gasoline. In order to fully understand the effect of ethanol on soot reducing, the soot characteristics of ethanol/gasoline blends were studied on laminar diffusion flames. In this experiment, the blending ratio of ethanol/gasoline was set as E0/20/40/60/80. Considering the carbon content decreasing due to ethanol addition, carbon mass flow rate was remained constant. The two-dimensional distributions of soot volume fraction were measured quantitatively by using two-color laser induced incandescence technique. The results showed that ethanol is able to decrease the soot significantly, but the effect of ethanol on soot reduction is weakened with the increasing ethanol ratio.
2017-10-08
Technical Paper
2017-01-2382
Tul Suthiprasert, Sirichai Jirawongnuson, Ekathai Wirojsakunchai, Tanet Aroonsrisopon, Krisada Wannatong, Atsawin Salee
Abstract The diesel dual fuel engine emits CH4 in the exhaust gas. This makes the exhaust gas more difficult to treat comparing to the exhaust gas from the conventional engine since CH4 requires high exhaust temperature to oxidize. In addition, another parameter such as exhaust flow rate, specie concentrations, especially CO, C3H8, and H2O have tremendous impact on Diesel Oxidation Catalyst performance on reducing CH4. This research is aimed to propose a kinetic model based on Langmuir Hinshelwood mechanisms that includes several terms such as CH4, C3H8, CO, O2, and H2O concentrations in order to gain a better understanding on the catalytic reaction and to provide a simulation with an accurate prediction. The model’s kinetic parameters are determined from the experiment by using synthetic gas. The composition of synthetic gas is simulated to be similar to the real exhaust gas from diesel dual fuel engines.
2017-10-08
Technical Paper
2017-01-2390
Hongxue Zhao, Daliang Jing, Yinhui Wang, Shi-jin Shuai, Changle PANG
Abstract In this paper, the impacts of Aromatic and Olefin on the formation of poly-aromatic hydrocarbons (PAHs) in the gasoline direct injection (GDI) engine were experimentally and numerically investigated. The objective of this study is to describe the formation process of the soot precursors including one ring to four ring aromatics (A1-A4). In order to better understand the effects of the fuel properties on the formations of PAHs. Three types of fuels, namely base gasoline, gasoline with higher aromatics content, and gasoline with higher olefin content were experimentally studied. At the same time, these aspects were also numerically investigated in the CHEMKIN code by using premixed laminar flame model and surrogated fuels. The results show that higher aromatics content in gasoline will lead to much higher PAHs formation. Similar trend was also found in the gasoline with higher olefin content.
2017-10-08
Technical Paper
2017-01-2404
Douglas Ball, David Lewis, David Moser, Sanket Nipunage
Abstract Federal Test Procedure (FTP) emissions were measured on a 2009 4 cylinder 2.4L Malibu PZEV vehicle with 10 and 30ppm sulfur fuel while varying the PGM (Platinum Group Metals) of the close-coupled and underfloor converters. Base CARB PH-III certification fuel was used. Three consecutive FTPs were used to measure the impact of fuel sulfur and catalyst PGM loading combinations. In general, reducing fuel sulfur and increasing catalyst PGM loadings, decrease FTP emissions. Increasing Pd concentrations can mitigate the impact of higher fuel sulfur concentrations. The results also suggest that a 50% reduction in PGM can be achieved with a reduction in fuel sulfur from 30 to 10 ppm. On average, NMHC, CO and NOx emissions were reduced by 12, 49 and 64%, respectively with the 10 ppm sulfur fuel. In addition, HC and NOx vehicle emission variability were reduced by 74 and 57% with the 10 ppm sulfur fuel.
2017-10-08
Technical Paper
2017-01-2405
Christophe Chaillou, Alexandre Bouet, Arnaud Frobert, Florence Duffour
Abstract Fuels from crude oil are the main energy vector used in the worldwide transport sector. But conventional fuel and engine technologies are often criticized, especially Diesel engines with the recent “Diesel gate”. Engine and fuel co-research is one of the main leverage to reduce both CO2 footprint and criteria pollutants in the transport sector. Compression ignition engines with gasoline-like fuels are a promising way for both NOx and particulate emissions abatement while keeping lower tailpipe CO2 emissions from both combustion process, physical and chemical properties of the low RON gasoline. To introduce a new fuel/engine technology, investigation of pollutants and After-Treatment Systems (ATS) is mandatory. Previous work [1] already studied soot behavior to define the rules for the design of the Diesel Particulate Filter (DPF) when used with a low RON gasoline in a compression ignition engine.
2017-10-08
Technical Paper
2017-01-2407
Michael Bardon, Greg Pucher, David Gardiner, Javier Ariztegui, Roger Cracknell, Heather Hamje, Leonardo Pellegrini, David Rickeard
Abstract Low Temperature Combustion using compression ignition may provide high efficiency combined with low emissions of oxides of nitrogen and soot. This process is facilitated by fuels with lower cetane number than standard diesel fuel. Mixtures of gasoline and diesel (“dieseline”) may be one way of achieving this, but a practical concern is the flammability of the headspace vapours in the vehicle fuel tank. Gasoline is much more volatile than diesel so, at most ambient temperatures, the headspace vapours in the tank are too rich to burn. A gasoline/diesel mixture in a fuel tank therefore can result in a flammable headspace, particularly at cold ambient temperatures. A mathematical model is presented that predicts the flammability of the headspace vapours in a tank containing mixtures of gasoline and diesel fuel. Fourteen hydrocarbons and ethanol represent the volatile components. Heavier components are treated as non-volatile diluents in the liquid phase.
2017-10-08
Technical Paper
2017-01-2401
Elana Chapman, Pat Geng, Yaowei Zhao, Susan Zhang, JunJun Ma, Jianqiang Gong
Abstract The impact of gasoline composition on vehicle particulate emissions response has been widely investigated and documented. Correlation equations between fuel composition and particulate emissions have also been documented, e.g. Particulate Matter Index (PMI) and Particulate Evaluation Index (PEI). Vehicle PM/PN emissions correlate very well with these indices. In a previous paper, global assessment with PEI on fuel sooting tendency was presented [1]. This paper will continue the previous theme by the authors, and cover China gasoline in more detail. With air pollution an increasing concern, along with more stringent emission requirements in China, both OEMs and oil industries are facing new challenges. Emissions controls require a systematic approach on both fuels and vehicles. Chinese production vehicle particulate emissions for a range of PEI fuels are also presented.
2017-10-08
Technical Paper
2017-01-2403
Yanzhao An, R Vallinayagam, S Vedharaj, Jean-Baptiste Masurier, Alaaeldin Dawood, Mohammad Izadi Najafabadi, Bart Somers, Bengt Johansson
Abstract In-cylinder visualization, combustion stratification, and engine-out particulate matter (PM) emissions were investigated in an optical engine fueled with Haltermann straight-run naphtha fuel and corresponding surrogate fuel. The combustion mode was transited from homogeneous charge compression ignition (HCCI) to conventional compression ignition (CI) via partially premixed combustion (PPC). Single injection strategy with the change of start of injection (SOI) from early to late injections was employed. The high-speed color camera was used to capture the in-cylinder combustion images. The combustion stratification was analyzed based on the natural luminosity of the combustion images. The regulated emission of unburned hydrocarbon (UHC), carbon monoxide (CO) and nitrogen oxides (NOX) were measured to evaluate the combustion efficiency together with the in-cylinder rate of heat release.
2017-10-08
Technical Paper
2017-01-2409
Erbao Zhang, Yinchun Gong, Jun Deng, Zongjie Hu, Chuanqian Jiang, Zhijun Wu, Liguang Li
Abstract The work of this paper aimed at investigating the cyclic variations of argon power cycle engine with fuel of hydrogen at lean burn operating conditions. The engine had been modified based on a 0.402 L, single-cylinder diesel engine into spark ignition engine with a port fuel injection system. The influencing factors on the cyclic variations, such as ignition timing, engine speed and compression ratio, were tested in this study. In all tests, the throttle opened at 0%, and the excess oxygen coefficient was maintained at 2.3. The results showed that as the ignition timing retards, CoVPmax and CoV(dp/dφ)max of argon power cycle engine increased, while CoVIMEP decreased firstly and increased afterward. And there is an ignition timing to make the lowest CoVIMEP, which is not consistent with MBT.
2017-10-08
Technical Paper
2017-01-2422
Na Li, Fenlian Huang, Yuhua Bi, Yueqiang Xu, Lizhong Shen, Dewen Jia
Abstract The assembly of con rod bearing and crankpin is a key friction pair which offers an important guarantee for stable operation of diesel engine. Specific to the non-road 2-cylinder diesel engine developed independently and based on the theory of thermoelastohydrodynamic lubrication as well as multi-body dynamics, this paper establishes a multi-body dynamics model for con rod big end bearings of the 2D25 horizontal diesel engine and makes a research on the influence of bearing width, bearing clearance, and oil inlet position and diameter upon lubrication of con rod bearing, taking into consideration that of the surface appearance of bearing bush and the elastic deformation of bearing bush and axle journal upon the same. Research results show that bearing width and bearing clearance are the major factors that influence lubrication characteristics of con rod bearing while oil inlet position and diameter only have a small influence on such characteristics.
Viewing 1 to 30 of 14423