Criteria

Text:
Topic:
Content:
Display:

Results

Viewing 1 to 30 of 142
CURRENT
2017-11-20
Standard
AMSQQA200/4C
This specification covers the specific requirements for aluminum alloy 5083 bar, rod, shapes, tube, and wire produced by extrusion.
CURRENT
2017-10-25
Standard
AMS4350N
This specification covers a magnesium alloy in the form of extruded bars, rods, wire, tubing, and profiles.
CURRENT
2017-10-18
Standard
AMS4337B
This specification covers an aluminum alloy in the form of extruded profiles (shapes) 0.500 to 1.500 inch, incl (12.7 to 38.1 mm, incl) in nominal thickness, and having a maximum cross-sectional area of 20 in2 (129 cm2) and a maximum circle size of 10 inches (254 mm) (see 8.7).
CURRENT
2017-09-13
Standard
AMS4163F
This specification covers an aluminum alloy in the form of extruded bars, rods, wire, profiles, and tubing up to 2.999 inches, incl (76.17 mm, incl) in thickness, nominal diameter or wall thickness with cross-sectional area 25 in2 (161 cm2) and under (see 8.5).
CURRENT
2017-09-05
Standard
AMS4935L
This specification covers a titanium alloy in the form of extruded bars and shapes, flash welded rings 3.000 inches (76.20 mm) and under in nominal diameter or least distance between parallel sides, and stock for flash welded rings.
CURRENT
2017-08-07
Standard
AMS4485A
This specification covers a magnesium alloy in the form of extruded bars, rods, wire, tubing, and profiles from 0.039 to 4.75 inches, incl. (12.71.0 to 120.7 mm., incl.) in nominal thickness (see 8.4).
CURRENT
2017-08-04
Standard
AMSR25988A
This specification covers oil-and-fuel-resistant fluorosilicone elastomer rubber sheets, strips, molded parts, and extruded shapes for aeronautical and aerospace applications.
CURRENT
2017-06-09
Standard
AMS4352J
This specification covers a magnesium alloy in the form of extruded bars, rods, wire, tubing, and profiles up to 40 in2 (258 cm2) in cross-sectional area (solids) and up to 8.5 inches (216 mm) OD by 1.188 inches (30.18 mm) wall thickness (tubing) (see 8.4).
CURRENT
2017-05-30
Standard
AMS4416B
This specification covers an aluminum-lithium alloy in the form of extruded profiles 0.040 to 1.000 inch, incl in thickness (see 8.5).
2017-05-09
WIP Standard
AMS4347E
This specification covers an aluminum alloy in the form of sheet from 0.020 to 0.249 inch (0.51 to 6.32 mm), inclusive, in thickness (See 8.5).
CURRENT
2017-04-24
Standard
AMS4307C
This specification covers an aluminum alloy in the form of extruded bars, rods, wire, profiles, and tubing.
CURRENT
2017-04-04
Standard
AMS4309B
This specification covers an aluminum alloy powder metallurgy product in the form of round extrusions up to 3.5 inches (89 mm) in diameter and rectangular and other solid extrusions up to 10 square inches (64.5 cm2) in cross-sectional area. The maximum extrusion length is 100 inches (2.5 m).
CURRENT
2017-04-03
Standard
AMS4617A
This specification covers an aluminum alloy in the form of extruded bars, rods, wire, shapes, and tubing 0.040 to 4.499 inches (1.01 to 114.27 mm) inclusive, in nominal diameter or least thickness, and with areas up to 32 in2 (206 cm2), inclusive (see 8.5).
CURRENT
2017-03-30
Standard
AMS4933F
This specification covers a titanium alloy in the form of extruded bars, tubes, and shapes, and flash welded rings up through 4.000 in2 (25.81 cm2) cross-section and stock for flash welded rings.
CURRENT
2017-03-28
Standard
J1639_201703
This SAE Recommended Practice provides a system for classification and specification for limited number of polyamides (nylons) used in the Automotive Industry. Based upon ASTM D 4066, Classification System for Nylon Injection and Extrusion Materials (PA), it calls for additional descriptive characteristics and properties commonly used in the Automotive Industry. This document applies to natural and non-color matched black, heat-stabilized polyamide compounds only. Color matched compounds shall be defined by the proprietary OEM standards. This document allows for the use of recycled, reconstituted, and regrind materials provided that the requirements as stated in this document are met, the material has not been altered or modified to change its suitability for safe processing and use, and the material shall be identified as such.
CURRENT
2016-12-01
Standard
ARP5369B
These guidelines have been written to provide process information regarding the hot stamp method of marking wire identification directly on aerospace wires and cables.
CURRENT
2016-11-18
Standard
J1053_201611
Included herein are general, dimensional, and performance specifications for those types, styles, and sizes of stamped nuts of one pitch thread design recognized as SAE standard. These nuts are intended for general use where the engagement of a single thread on the mating screw or unthreaded stud is considered adequate for the application. For the metric equivalent of this document, see SAE J1053M.
CURRENT
2016-11-18
Standard
J1053M_201611
Included herein are general, dimensional, and performance specifications for those types, styles, and sizes of stamped nuts of one pitch thread design recognized as SAE standard. These nuts are intended for general use where the engagement of a single thread on the mating screw or unthreaded stud is considered adequate for the application. For the inch equivalent of this document, see SAE J1053.
CURRENT
2016-08-01
Standard
AMS4963D
This specification covers a titanium alloy in the form of bars, wire, forgings, flash welded rings up through 3.999 inches (101.57 mm), inclusive and stock for forging, flash welded rings, or heading.
CURRENT
2016-08-01
Standard
AMS4973H
This specification covers a titanium alloy in the form of forgings up to 4.000 inches (101.60 mm) inclusive and forging stock.
CURRENT
2016-02-29
Standard
AMS3678/11A
This specification covers a polytetrafluoroethylene (PTFE) resin filled with 10% aromatic polymer in the form of extruded or molded rods or tubes which are sintered after molding or, in the case of extrusions, sintered during the extrusion process.
CURRENT
2016-02-29
Standard
AMS3678/10B
This specification covers a polytetrafluoroethylene (PTFE) resin filled with carbon fiber in the form of extruded or molded rods or tubes which are sintered after molding or, in the case of extrusions, sintered during the extrusion process.
CURRENT
2016-02-29
Standard
AMS3678/7B
This specification covers a polytetrafluoroethylene (PTFE) resin filled with carbon and graphite in the form of extruded or molded rods or tubes which are sintered after molding or, in the case of extrusions, sintered during the extrusion process.
CURRENT
2016-02-29
Standard
AMS3678/3B
This specification covers a polytetrafluoroethylene (PTFE) resin filled with 15% glass fiber and 5% molybdenum disulfide in the form of extruded or molded rods or tubes which are sintered after molding or, in the case of extrusions, sintered during the extrusion process.
CURRENT
2016-02-29
Standard
AMS3678/5B
This specification covers a polytetrafluoroethylene (PTFE) resin filled with inorganic pigment in the form of extruded or molded rods or tubes which are sintered after molding or, in the case of extrusions, sintered during the extrusion process.
CURRENT
2016-02-29
Standard
AMS3678/16A
This specification covers a polytetrafluoroethylene (PTFE) resin filled with 15% polyimide in the form of extruded or molded rods or tubes which are sintered after molding or, in the case of extrusions, sintered during the extrusion process.
CURRENT
2016-02-29
Standard
AMS3678/2B
This specification covers a polytetrafluoroethylene (PTFE) resin filled with 15% graphite in the form of extruded or molded rods or tubes which are sintered after molding or, in the case of extrusions, sintered during the extrusion process.
CURRENT
2016-02-29
Standard
AMS3678/12A
This specification covers a polytetrafluoroethylene (PTFE) resin filled with 10% mineral and 2.5% molybdenum disulfide in the form of extruded or molded rods or tubes which are sintered after molding or, in the case of extrusions, sintered during the extrusion process.
Viewing 1 to 30 of 142

Filter

  • Standard
    142