Criteria

Text:
Display:

Results

Viewing 1 to 30 of 2146
2017-03-28
Technical Paper
2017-01-0215
Mohammad Nahid, Amin Sharfuzzaman, Joydip Saha, Harry Chen, Sadek S. Rahman
More stringent Federal emission regulations and fuel economy requirements have driven the automotive industry toward more sophisticated vehicle thermal management systems to best utilize the waste heat and improve driveline efficiency. The final drive unit in light and heavy duty trucks usually consists of geared transmission and differential housed in a lubricated axle. The automotive rear axles is one of the major sources of power loss in the driveline due to gear friction, churning and bearing loss and have a significant effect on overall vehicle fuel economy. These losses vary significantly with the viscosity of the lubricant. Also the temperatures of the lubricant are critical to the overall axle performance in terms of power losses, fatigue life and wear.
2017-03-28
Technical Paper
2017-01-0216
Joydip Saha, Harshit Coutinho, Sadek S. Rahman
Current and future automotive systems are becoming more complex than ever. They consist of different subsystems such as the engine, transmission, cooling system, driveline, controls systems, HVAC and active/passive safety systems. Hardware and software development for each of these subsystems have different timeline’s. The subsystems are usually developed by different teams within an organization and in some cases are also developed by suppliers. These are some of the main hurdles for carrying out a system level analysis of the vehicle earlier in the development process. Model.CONNECT was used to overcome the above mentioned hurdles by connecting a driveline model, a cooling system model, thermal controller and two-phase flow models with minimal effort.
2017-03-28
Technical Paper
2017-01-0214
Simon O. Omekanda, Rezwanur Rahman, Eric M. Lott, Sadek S. Rahman, Daniel E. Hornback
Designing an efficient transient thermal system model has become a very important task in improving fuel economy. As opposed to steady-state thermal models, part of the difficulty in designing a transient model is optimizing a set of inputs. The first objective in this work is to develop an engine compatible physics-based 1D thermal model for fuel economy and robust control. In order to capture and study the intrinsic thermo-physical nature, both generic “Three Mass” and “Eight Mass” engine model are developed. The models have been correlated heuristically using Simulink and Flowmaster, respectively. In order to extend the lumped mass engine model it also has been extended to Simulink model. In contrast to the complexity of the models the “Heuristic search” of input parameters has been found to be challenging and time consuming.
2017-03-28
Technical Paper
2017-01-0212
Mohammad Nahid, Rezwanur Rahman, Tabassum Hossainy, Shreyas Kapatral, Prashant Modi, Joydip Saha, Sadek S. Rahman
More stringent Federal emission regulations and fuel economy requirements have driven the automotive industry toward more efficient vehicle thermal management systems to best utilize the heat produced from burning fuel and improve driveline efficiency. The greatest part of the effort is directed toward the hybridization of automotive transmission systems. The efficiency and durability of hybrid powertrain depends on the heat generation in electric motors and their interactions among each other, ambient condition, the cooling system and the transmission component configuration. These increase the complexity of motor temperature prediction as well as the computational cost of running a conjugate heat-transfer based CFD analysis. In this paper, 1-D physics based thermal model is developed which allows rapid and accurate component-wise temperature estimation of the electric motor as well as transmission lubricant temperature during both steady-state and transient driving cycles.
2017-03-28
Technical Paper
2017-01-1140
Yang Xu, Yuji Fujii, Edward Dai, James McCallum, Gregory Pietron, Guang Wu, Hong Jiang
Abstract A transmission system model is developed at various complexities in order to capture the transient behaviors in drivability and fuel economy simulations. A large number of model parameters bring more degree of freedom to correlate with vehicular test data. However, in practice, it requires extensive time and effort to tune the parameters to satisfy the model performance requirements. Among the transmission model, a hydraulic clutch actuator plays a critical role in transient shift simulations. It is particularly difficult to tune the actuator model when it is over-parameterized. Therefore, it is of great importance to develop a hydraulic actuator model that is easy to adjust while retaining sufficient complexity for replicating realistic transient behaviors. This paper describes a systematic approach for reducing the hydraulic actuator model into a piecewise 1st order representation based on piston movement.
2017-03-28
Technical Paper
2017-01-1565
Xiangkun He, Kaiming Yang, Xuewu Ji, Yahui Liu, Weiwen Deng
Abstract A vehicle dynamics stability control system based on integrated-electro-hydraulic brake (I-EHB) system with hierarchical control architecture and nonlinear control method is designed to improve the vehicle dynamics stability under extreme conditions in this paper. The I-EHB system is a novel brake-by-wire system, and is suitable to the development demands of intelligent vehicle technology and new energy vehicle technology. Four inlet valves and four outlet valves are added to the layout of a conventional four-channel hydraulic control unit. A permanent-magnet synchronous motor (PMSM) provides a stabilized high-pressure source in the master cylinder, and the four-channel hydraulic control unit ensures that the pressures in each wheel cylinder can be modulated separately at a high precision. Besides, the functions of Anti-lock Braking System, Traction Control System and Regenerative Braking System, Autonomous Emergency Braking can be integrated in this brake-by-wire system.
2017-03-28
Technical Paper
2017-01-1284
Khushal Ahmad, Monis Alam
Abstract With the ever increasing number of vehicles on road and the rise of the electric and automated vehicles, it is important to minimize the consumption of energy by each vehicle, regenerative braking is in wide use today, however, the research in the field of regenerative suspension is limited. The regenerative suspension has huge capabilities in power generation especially on third world roads having rather bumpy rides. A huge amounts of energy is wasted in shock absorbers due to friction. This study emphasizes on the implementation of the energy present in the suspension system by replacing the Shock Absorber with a Energy transfer system Involving Hydraulic cylinder, Hydraulic Motor and Dynamo. The energy which is usually lost as heat due to friction in conventional Suspension is used to drive a dynamo through Hydraulic System designed in this paper and electricity is generated.
2017-03-28
Journal Article
2017-01-0411
Yuming Yin, Subhash Rakheja, Jue Yang, P-E. Boileau
Abstract This study is aimed at characterizing the nonlinear stiffness and damping properties of a simple and low cost design of a hydro-pneumatic suspension (HPS) that permits entrapment of gas into the hydraulic fluid. The mixing of gas into the oil yields highly complex variations in the bulk modulus, density and viscosity of the hydraulic fluid, and the effective gas pressure, which are generally neglected. The pseudo-static and dynamic properties of the HPS strut were investigated experimentally and analytically. Laboratory tests were conducted to measure responses in terms of total force and fluid pressures within each chamber under harmonic excitations and nearly steady temperature. The measured data revealed gradual entrapment of gas in the hydraulic fluid until the mean pressure saturated at about 84% of the initial pressure, suggesting considerably reduced effective bulk modulus and density of the hydraulic fluid.
2017-03-28
Technical Paper
2017-01-1490
Silvia Faria Iombriller
Abstract The air suspension development and its applications have becoming increasingly relevant for commercial vehicles to provide dynamic ride comfort to driver and reduce the load impact onto driver and or cargo. This paper shows the analysis and application of an air suspension system for commercial tractor vehicles and its dynamic influence. A special focus was given to pneumatic actuation system, responsible for leveling and control of suspension´s stiffness under different conditions of usage, laden and unladed. The project was conducted starting with the vehicle dynamic performance analysis, evaluating the pneumatic suspension circuit modifications in order to obtain vehicle dynamic behavior improvement, ensuring directional stability under different maneuvering conditions.
2017-03-28
Journal Article
2017-01-1578
Tianyang Liu, Zhuoping Yu, Lu Xiong, Wei HAN
Abstract Two control strategies, safety preferred control and master cylinder oscillation control, were designed for anti-lock braking on a novel integrated-electro-hydraulic braking system (I-EHB) which has only four solenoid valves in its innovative hydraulic control unit (HCU) instead of eight in a traditional one. The main idea of safety preferred control is to reduce the hydraulic pressure provided by the motor in the master cylinder whenever a wheel tends to be locking even if some of the other wheels may need more braking torque. In contrast, regarding master cylinder oscillation control, a sinusoidal signal is given to the motor making the hydraulic pressure in the master cylinder oscillate in certain frequency and amplitude. Hardware-in-the-loop simulations were conducted to verify the effectiveness of the two control strategies mentioned above and to evaluate them.
2017-01-10
Technical Paper
2017-26-0235
Vinaykumar Dhangar, Solairaj Perumal, Abhay Kumar, Dinesh Redkar, Arun Mahajan, Abhirup Chakraborty, T Ganesan
Abstract A tractor is vehicle specifically designed to deliver a high tractive effort at slow speeds for carrying out various agriculture operations like ploughing, rotavation etc. using implement. Hydraulic system is a key feature which connects these implements with the tractor. It controls the position and draft of the implement depending upon the type of crop, farming stage, implement type and soil conditions. These variations induces extreme range of load on the hydraulic system, thus making it challenging to design these components. Bell crank assembly is one of the main components of hydraulic system which controls the draft (thus, the loads experienced by tractor) through load sensing mechanism. Often bell crank assembly failures are reported from field due to uneven soil hardness and presence of rocks. This paper studies one of such bell crank assembly failures in the field. The failure was reported after half life cycle of usage during agriculture Operation.
2017-01-10
Technical Paper
2017-26-0058
Mirko Leesch, Erik Schreiterer, Gitesh Mutha
Abstract The paper presents a new 7-speed dual-clutch transmission (DCT) for transverse applications and a torque capacity of 200 Nm with an option for 300 Nm engine torque. Advantageously the system is designed for supplier parts of dual-clutch system, gear and clutch actuation, differential as well as bearings, synchronizers and additional standardized parts. The actuation could be also realized by an already developed hydraulic module which can be used and produced locally with supplier parts of valves, sensors and so on. Furthermore, the gear set is a state-of-the-art system which can be supplied by manual transmission manufacturer. Beside the cost focus. the DCT has a favorable gear set in terms of robustness and compactness. The design with a total length of 350 mm is realized through a common gear on the main shaft for each gear pair on the countershafts and multiple use of gears in the first speed.
2017-01-10
Technical Paper
2017-26-0362
Arun Kumar Prasad, Babasaheb Shinde, V A Gopalakrishn
Abstract Hydraulic Load sensing brake valves are used in vehicles from a long time in the market. They proportionate the rear brake line pressure according to the rear axle load in order to avoid the rear wheel lock during braking. During the actual test of the Hydraulic load sensing valve on a subject vehicle, there was drop in performance against its expected peak brake performance. In the current work a detailed analysis is made to understand the sensitivity of the load sensing valve & its effect on the vehicle performance. The parameters affecting the valve sensitivity along with vehicle level factors affecting the performance are analysed during the work.
2017-01-10
Technical Paper
2017-26-0373
Jatinkumar Janshali, G R M Rao
Abstract Close loop motion control implementation for electro hydraulic system with multistage telescopic cylinder aimed to articulate heavy load to desired angle while keeping acceleration, velocity of load and time to reach the desired angle within acceptable limit possesses stringent control system strategies. Conventional PID (Proportional-Integral-Derivative) control algorithm cannot be applied directly to control the system as these algorithms are also required to meet various other criteria apart from just to stabilize the system around the set point. In case of fail to meet these criteria can cause the damage to the components of subjected system and lead to disaster in worst case scenario. This paper describes the model based design approach to implement smooth motion control for heavy duty systems.
2017-01-10
Technical Paper
2017-26-0340
Sarang Bire, Prashant R Pawar, M Saraf
Abstract Air suspension systems had been introduced in automobiles since 1950s. These systems are being explored to improve the ride comfort, handling stability and also serve as a medium for better cargo protection. These system are well developed for buses and high end passenger sedans, also have feasibility for adapting for wide range of configurations of suspension system and axle. Passenger cars and Sports Utility Vehicle (SUV) pickup category of vehicle offers different challenges such as space availability, spring selection and characterization that need to be addressed for successful implementation of air suspension in these category vehicles. This work defines methodology to implement air suspension system in SUV Pickup category vehicle. Paper work includes concept study, mathematical co-relation, and prediction of air spring characteristics and integration of experimental and analytical tool for development of air suspension system.
2017-01-10
Journal Article
2017-26-0227
Babu Bhondave, T Ganesan, Naveen Varma, Rajasekar Renu, N Sabarinath
Abstract Tractor hitch control system is used for attaching and operating various Agricultural Implements and for operating tipping trailer. The system has also got provision to attach additional Aux valves for rear and front mounted attachments. The rear mounted implements are coupled to the tractor using Three Point Linkage (3PL) System. The hitch hydraulics system consists of hydraulic pump, filter, piping’s, fittings and hydraulics lift unit. Hydraulics lift unit consists of a proportional control valve, cylinder, piston and power linkages. Conventional control valve is hydro mechanical part operated by mechanical linkages. The control valve and linkages plays major role in performance of hydraulics system. Hydraulics is required to operate in extreme conditions of soils such as very soft like sand to very hard like black cotton sand.
2016-09-27
Technical Paper
2016-01-8085
Yanjun Ren, Gangfeng Tan, Kangping Ji, Li Zhou, Ruobing Zhan
Abstract The hydraulic retarder is an auxiliary braking device generally equipped on commercial vehicles. Its oil temperature change influences the brake performance of hydraulic retarder. The Organic Rankine Cycle (ORC) is a good means to recover exhausted heat. Moreover, it can cool oil and stably control oil temperature with the help of heat absorption related with evaporation. Comprehensively considering the heat-producing characteristics of hydraulic retarder and the temperature control demand, the aimed boundary conditions are determined. Also the changing rules about the working medium flow rate are obtained. In this work, the heat-producing properties of hydraulic retarder under different conditions and the oil external circulating performance is firstly analyzed. By researching the system’s adaptation to the limiting conditions, the aimed temperature to control is prescribed.
2016-09-27
Technical Paper
2016-01-8117
Xingyu Zhang, Bo Yang, Can Wang, Zhilei Li, Yongqiang Ge, Zhongjie Yang, Xue Liu
Abstract The cooling system with two fans is generally driven by electrical motors in the small cars. Compared with the traditional cars, heavy duty trucks have the larger heat dissipation power of cooling system. The motors power consumption of dual fans will be larger and the two electrical motors will occupy a large space in the engine cabin. Hydrostatic drive refers to the cooling fan is driven by hydraulic motor, but it has the low transmission efficiency. According to the engine water temperature value and the actual working status of the hydraulic system, the actual speed of cooling fan can be controlled by the computer, which guarantees the normal working water temperature of the engine. Hydrostatic drive is generally applied to heavy vehicles, engineering machinery and excavators as driving source of cooling fan which contains the advantages of large output power, overload protection, continuous speed regulation and flexible space arrangements.
2016-09-27
Technical Paper
2016-01-8115
Jaehong Kim, Jae Y. Lee, Ahnkyun Jung
Abstract Construction equipment machines today benefits from hydraulic system due to high power density. And, the development of an excavator using “open-center system with spool valves”, in general, requires iterative hardware design tuning activities for optimized performance and fuel economy while matching operator’s commands. Instead of traditional hydraulic and multi-body dynamic simulation with an operator simulation model, this paper focuses on the methodology development of real-time simulation model for an excavator, including the hydraulic system of an excavator’s boom, arm, bucket, and travel as well as multi-body dynamic system. The real-time capability is realized by reducing unnecessary compressible units and achieving numerical stability at sudden pressure changes when valves open and close. The real-time simulation model has been verified later with an actual Volvo CE excavator machine, and the correlation was quite satisfactory.
2016-09-27
Technical Paper
2016-01-8116
Mrudula Uday Orpe, Monika Ivantysynova
Abstract Mobile Earth Moving Machinery like Skid-steer loaders have tight turning radius in limited spaces due to a short wheelbase which prevents the use of suspensions in these vehicles. The absence of a suspension system exposes the vehicle to ground vibrations of high magnitude and low frequency. Vibrations reduce operator comfort, productivity and life of components. Along with vibrations, the machine productivity is also hampered by material spillage which is caused by the tilting of the bucket due to the extension of the boom. The first part of the paper focuses on vibration damping. The chassis’ vibrations are reduced by the use of an active suspension element which is the hydraulic boom cylinder which is equivalent to a spring-damper. With this objective, a linear model for the skid steer loader is developed and a state feedback control law is implemented.
2016-09-27
Technical Paper
2016-01-8119
Jun Sun, Xiaofei Pei, Xuexun Guo, Yanqiang Zhao
Abstract In order to overcome hysteresis and dead zone problems caused by friction for the proportional solenoid valve, and improve rapidity and stability of the pneumatic system on hydraulic retarder, a closed-loop control strategy based on valve coil current was proposed. The high-frequency low-amplitude dither signal was introduced into the proportional solenoid valve. With the proper dither signal, the stick-slip motion of the valve core was transformed into a steady one, and its dynamic performance was improved. Consequently, response time of retarder was reduced during gear changing. The proportional valve coil current was measured as a feedback for a closed-loop control strategy. Combining with the closed-loop strategy, the PI control algorithm was adopted to make sure that valve current was in accordance with the target value. Pulse Width Modulation (PWM) signal was used for the driving of proportional solenoid valve.
2016-09-27
Technical Paper
2016-01-8114
Massimiliano Ruggeri, Pietro Marani, Michele Selvatici
Abstract Stationary (parking) brake is a very important and safety critical function in many classes of machines. The new transmissions and the “by wire” systems increase the criticality of the role of stationary brake, as it is also an emergency (secondary) brake, and it’s often used to hold the vehicle when the transmission is not locking the wheels. As an example, dual clutch and power-shift transmission gear systems, as well as hydrostatic transmissions under certain circumstances, are often unable to hold the vehicle stopped and this function is provided by the stationary brake. Due to the main need of having the brake actuated when vehicle is stopped, without any hydraulic and electric power, the brake configuration is normally a “negative” configuration, usually called “spring applied” because of the actuator configuration, but this configuration causes the brake actuation when de-energized, even in case of system failure.
2016-09-27
Technical Paper
2016-01-8079
Zhiwei Zhang, Gangfeng Tan, Mengying Yang, Zhongjie Yang, Mengzuo Han
Abstract The hydraulic retarder is an important auxiliary braking device. With merits such as its high braking torque, smooth braking, low noise, long service life and small size, it is widely used on modern commercial vehicles. Transmission fluid of traditional hydraulic retarder is cooled by engine cooling system, which exhausts the heat directly and need additional energy consumption for the thermal management component. On account of the working characteristics of hydraulic retarder, this study designs a set of waste heat recovery system based on the Organic Rankine Cycle (ORC). Under the premise of ensuring stable performance of hydraulic retarder, waste heat energy in transmission fluid is recycled to supplement energy requirements for cooling system. First of all, a principle model, which is scaled down according to D300 retarder`s thermal power generation ration of 1:100, is established.
2016-09-27
Technical Paper
2016-01-8113
Xiaohua Zeng, Guanghan Li, Dafeng Song, Sheng Li, Xianghua Li
Abstract To improve traditional heavy commercial vehicles performance, this paper introduces a novel hydraulic hub-motor auxiliary system, which could achieve auxiliary driving and auxiliary braking function. Firstly, the system configuration and operation modes are described. In order to achieve coordinating control and distribution of the engine power between mechanical and hydraulic paths, the paper proposes an optimal algorithm based on enhance of vehicle slip efficiency and the results show that displacement of hydraulic variable pump relates with the transmission gear ratio. And then the hydraulic pump displacement controller is designed, in which the feedforward and feedback strategy is adopted. Considering the characteristics of hydraulic hub-motor auxiliary system, a layered auxiliary drive control strategy is proposed in the paper, which includes signal layers, core control layers and executive layers.
2016-09-27
Journal Article
2016-01-8063
David Ferreira, Thomas Howell, Peter Jo
Abstract Current heavy duty diesel valvetrains are not able to utilize hydraulic lash adjusters (HLA) in conjunction with an engine brake. During a braking event the engine brake introduces substantial lash into the vehicle valvetrain. The HLA reacts by pumping out to take up the lash encountered during braking, thereby preventing the valves from properly seating at the end of the cycle. Jacobs Vehicle Systems has developed a new mechanism to allow the inclusion of an engine brake into a valvetrain equipped with hydraulic lash adjusters. The fulcrum system maintains a load on the hydraulic lash adjuster during engine brake operation preventing the HLA from extending. HLA are appealing to engine manufacturers because they allow for simpler manufacturing, less maintenance, reduced NVH and valve motion enhancements. This paper describes the design, simulation and testing of the lashless valvetrain with engine brake including the next steps in the development of the valvetrain.
2016-09-27
Technical Paper
2016-01-8121
Riccardo Bianchi, Addison Alexander, Andrea Vacca
Abstract Typically, earthmoving machines do not have wheel suspensions. This lack of components often causes uncomfortable driving, and in some cases reduces machine productivity and safety. Several solutions to this problem have been proposed in the last decades, and particularly successful is the passive solution based on the introduction of accumulators in the hydraulic circuit connecting the machine boom. The extra capacitance effect created by the accumulator causes a magnification of the boom oscillations, in such a way that these oscillations counter-react the machine oscillation caused by the driving on uneven ground. This principle of counter-reacting machine oscillations through the boom motion can be achieved also with electro-hydraulic solutions, properly actuating the flow supply to the boom actuators on the basis of a feedback sensors and a proper control strategy.
2016-09-27
Journal Article
2016-01-8120
Marco Francia, Massimo Milani, Luca Montorsi
Abstract The paper focuses on the development of an innovative methodology for the direct measurement of the main kinematic variables in multibody hydraulic actuation systems. The analysis investigates how the motion capture technique has been applied to the experimental determination of position, velocity and acceleration of hydraulically controlled actuation systems for off-highway machines. A number of earth-moving machines has been taken into account, in particular a mini-excavator articulated arm has been equipped with both a standard mechanical system for position and acceleration measurement (including different accelerometers, linear and angular transducers), and a set of IR markers for motion capture application. First, the hydraulically controlled boom-arm-bucket system has been operated using a control routine reproducing a reference operating condition, in order to define the accuracy of the motion capture system in detecting the kinematic quantities’ variations.
2016-09-18
Technical Paper
2016-01-1941
Tie Wang, Gangfeng Tan, Xuexun Guo, Shengguang Xiong, Zhiwei Zhang, Xin Gao
Abstract Vehicle hydraulic retarders are applied in heavy-duty trucks and buses as an auxiliary braking device. In traditional cooling systems of hydraulic retarders, the working fluid is introduced into the heat exchanger to transfer heat to the cooling liquid in circulation, whose heat is then dissipated by the engine cooling system. This prevents the waste heat of the working fluid from being used effectively. In hydraulic retarder cooling system based on the Organic Rankine Cycle, the organic working fluid first transfers heat with the hydraulic retarder working fluid in Rankine cycle, and then outputs power through expansion machine. It can both reduce heat load of the engine cooling system, and enhance thermal stability of the hydraulic retarder while recovering and utilizing braking energy. First of all, according to the target vehicle model, hydraulic retarder cooling system model based on Rankine cycle is established.
2016-09-18
Technical Paper
2016-01-1938
Xin Gao, Gangfeng Tan, Binyu Mei, Mengzuo Han, Tie Wang
Abstract The hydraulic retarder is an auxiliary braking device used for commercial vehicle in a long slope brake, and its transmission oil generates a lot of heat in its working process. If the heat of transmission doesn’t go through a reasonable management, it will seriously affect the braking performance of hydraulic retarder. To cool down the transmission oil, it will aggravates the load of the engine cooling system, and the long cooling path sometimes causes heat exchange not timely. When the Rankine cycle is used for cooling the hydraulic retarder transmission oil in virtue of its good heat transfer performance in phase change process, it can make the transmission oil temperature controlled more stable. In this new system, the setting parameters of the Evaporate-condensate system will affect the stability of the transmission oil temperature in the hydraulic retarder inlet and the energy recovery efficiency of the system.
2016-09-18
Technical Paper
2016-01-1954
Zhe Xiong, Xiaofei Pei, Xuexun Guo, Chengcai Zhang
Abstract In this paper a new pressure control method of a modified accumulator-type Electro-hydraulic Braking System (EHB) is proposed. The system is composed of a hydraulic motor pump, an accumulator, an integrated master cylinder, a pedal feel simulator, valves and pipelines. Two pressurizing modes are switched between by-motor and by-accumulator to adapt different pressure boost demands. A differentiator filtering raw sensor signal and calculating pedal speed is designed. By using the pedal feel simulator, the relationship between wheel pressures and brake force is decoupled. The relationships among pedal displacement, pedal force and wheel pressure are calibrated by experiments. A model-based PI controller with predictor is designed to lower the influences caused by delay. Moreover, a self-tuning regulator is introduced to deal with the parameter’s time-varying caused by temperature, brake pads wearing and delay variation.
Viewing 1 to 30 of 2146

Filter