Criteria

Text:
Content:
Display:

Results

Viewing 1 to 30 of 177
2017-09-21
WIP Standard
AIR8012
The purpose of the document is to provide the guidelines of the technological approach for developing a PHM system for EMAs with particular reference to their possible use as primary flight control actuators. It provides a basic description of the physics of the most common degradation processes,a reliability assessment and a discussion on the signals, with the associated data processing, required to build up an effective health monitoring system.
CURRENT
2017-07-19
Standard
AIR4174A
The purpose of this SAE Aerospace Information Report (AIR) is to provide management, designers, and operators with information to assist them to decide what type of power train monitoring they desire. This document is to provide assistance in optimizing system complexity, performance and cost effectiveness. This document covers all power train elements from the point at which aircraft propulsion energy in a turbine or reciprocating engine is converted via a gear train to mechanical energy for propulsion purposes. The document covers aircraft engine driven transmission and gearbox components, their interfaces, drivetrain shafting, drive shaft hanger bearings, and associated rotating accessories, propellers, and rotor systems as shown in Figure 1. For guidance on monitoring additional engine components not addressed, herein (e.g., main shaft bearings and compressor/turbine rotors), refer to ARP1839.
CURRENT
2017-06-09
Standard
ARP1804B
This SAE Aerospace Recommended Practice (ARP) outlines the design and performance requirements for a battery-powered electric tow tractor for the handling of baggage or cargo trailers in airline service. The use of “shall” in this document indicates a mandatory requirement. The use of “should” indicates a recommendation or that which is advised but not required.
2017-03-13
WIP Standard
ARP4853D
The tow vehicle should be designed for towbarless movement of aircraft on the ground. The design will ensure that the unit will safely secure the aircraft nose landing gear within the coupling system for any operational mode.
2017-03-13
WIP Standard
ARP5283B
The purpose of this specification is to provide airplane operators and tow vehicle manufacturers with: a. General design and operating requirements pertinent to test and evaluation of towbarless tow vehicles. Specific design requirements are provided in ARP4852 and ARP4853. b. Test and evaluation requirements. The results of these test evaluations will determine if the loads induced by the tow vehicle will exceed the design loads of the nose gear, or are within the aircraft manufacturer’s limits so that they do not affect the certified safe limit of the nose gear. The results of these test evaluations will also determine if a stability problem may occur during pushback and/or maintenance towing operations with the tested airplane/tow vehicle combination. This document specifies general test requirements and a test evaluation procedure for towbarless tow vehicles (TLTV) intended for pushback and maintenance towing only.
CURRENT
2017-02-28
Standard
ARP1287B
This SAE Aerospace Recommended Practice (ARP) is applicable to any type of aerospace ground support vehicle, powered or unpowered.
2017-01-24
WIP Standard
AIR7999
This SAE Aerospace Information Report (AIR) presents metrics for assessing the performance of diagnostic and prognostic algorithms applied to Engine Health Management (EHM) functions. This document consolidates and expands upon the metric information previously contained in AIR4985 and AIR5909. The emphasis is entirely on metrics and as such is intended to provide an extension and complement to such documents as ARP4176, which provides insight into how to create a cost benefit analysis to determine the justification for implementing an EHM system.
2016-12-21
WIP Standard
ARP6915
This Aerospace Recommended Practice (ARP) offers best practice regarding the implementation of IVHM systems taking into account Human Factors, both the vehicle crew and the maintenance staff. The document will include considerations regarding both military and civil fixed wing aircraft. Safety implications will also be addressed.
CURRENT
2016-11-29
Standard
AIR1873A
This Aerospace Information Report (AIR) describes a Limited Engine Monitoring System that can be used by the flight crew or the maintenance staff, or both, to monitor the health of gas turbine engines in aircraft. This AIR considers monitoring of gas path performance and mechanical parameters, and systems such as low cycle fatigue counters and engine history recorders. It also considers typical measurement system accuracies and their impact. This AIR is intended as a technical guide. It is not intended to be used as a legal document or standard. AIR 1873 supplements ARP 1587, Aircraft Gas Turbine Engine Monitoring System Guide.
CURRENT
2016-06-06
Standard
AIR1589B
Only those incidents where a piece of ground support equipment directly associated with the "turnaround" servicing of an aircraft was involved are reviewed. Specifically excluded are those incidents that occurred during heavy maintenance, overhaul activity, or aircraft taxiing.
2016-06-01
WIP Standard
AIR6906
To document a lesson learnt that impulse towing loads are effected by tow tractor clevis and pin and towbar eye ring clearances. These impulse loads can be so large that they have damage the nose landing gear and aircraft structure of some aircraft. Damage occurs while operating within towing instruction
2016-05-17
WIP Standard
AIR6245
This document is applicable to military aircraft where stakeholders are seeking guidance on the development and approval of Structural Health Monitoring (SHM) technologies and on the integration of these technologies into encompassing maintenance and operational support systems. The document will refer to those guidelines prepared under SAE ARP6461 that are relevant and applicable to military applications.
2016-05-17
WIP Standard
JA6268
This Aerospace & Automotive Recommended Practice offers best practices and a methodology by which IVHM functionality relating to components and subsystems should be integrated into vehicle or platform level applications. The intent of the document is to provide practitioners with a structured methodology for specifying, characterizing and exposing the inherent IVHM functionality of a component or subsystem using a common functional reference model, i.e., through the exchange of design-time data and the application of standard vehicle data communications interfaces. This document includes best practices and guidance related to the specification of the information that must be exchanged between the functional layers in the IVHM system or between lower-level components/subsystems and the higher-level control system to enable health monitoring and tracking of system degradation severity.
2016-04-22
WIP Standard
ARP6904
In order to realize the benefits of Integrated Vehicle Health Management (IVHM) within the aerospace and defense industry there is a need to address five critical elements of data interoperability within and across the aircraft maintenance ecosystem, namely • Approach • Trust • Context • Value • Security In Integrated Vehicle Health Management (IVHM) data interoperability is the ability of different authorized components, systems, IT, software, applications and organizations to securely communicate, exchange data, interpret data, use the information and derive consistent insight from the data that has been exchanged to derive value.
2016-04-06
WIP Standard
AS85352A
This specification covers a direct reading, remote control, pneumatic pressure inflator assembly, for use on aircraft tires and struts having pneumatic pressure requirements up to 600 psi. It includes pressure relief provisions for safe inflation. Also included are dual chuck stem gages for measuring tire pressure.
CURRENT
2016-03-16
Standard
ARP6803
This SAE Aerospace Recommended Practice (ARP) examines a comprehensive construct of an Integrated Vehicle Health Management (IVHM) capability. This document provides a top-level view of the concepts, technology, and implementation practices associated with IVHM. This keystone document of the SAE HM-1 Committee is not intended as a legal document and does not provide detailed implementation steps, but does address general implementation concerns and potential benefits. Figure 1 provides a document flow map of the documents currently in work or planned by the Committee. The documents shown below will provide the recommended practices for IVHM implementation. This document map reflects the current SAE IVHM document configuration as of the date of publication. Future documents that are released will be included in the flow map in future updates of this document. An indication of the scope of IVHM is diagrammed in Figure 2.
CURRENT
2016-03-05
Standard
AS8090A
This specification covers general design and performance requirements for the mobility of towed ground support equipment. The complete mobility requirements for an item of towed aerospace ground equipment not specified herein shall be specified in the individual equipment specification (see 6.4).
2016-01-07
WIP Standard
ARP1247E
This SAE Aerospace Recommended Practice (ARP) outlines the basic general design requirements for ground support equipment used in the civil air transport industry. It is intended to assist in standardizing requirements for various configurations of equipment. For procurement of equipment, sections of this document should be specified with due consideration of the functional and environmental requirements of the equipment, and to the relative cost of satisfying those requirements.
2016-01-03
WIP Standard
AIR6900
This AIR will address the need for a strategy to achieve aircraft operating certificate holder maintenance efficiencies within the existing regulatory environment as well as the need for regulation, policy, and guidance changes in the long-term to accommodate more complex IVHM solutions. This document will analyse which IVHM solutions can be incorporated within existing maintenance procedures and which also comply with regulations, policy, and guidance. One of the AIR’s objectives is to define best practices for aircraft operating certificate holders to engage with regulators to get approval for simpler IVHM applications leading to maintenance efficiencies. Additionally, this document will analyse the barriers that existing regulations, policy, and guidance present to the implementation of more advanced IVHM solutions. The result is a set of recommendations to certify and implement end-to-end IVHM solutions for the purpose of gaining maintenance efficiencies.
2015-10-23
WIP Standard
AS6896
Definition of target design and location on aircraft, that will be used: - To provide correct GSE alignment support and docking when approaching the aircraft in automatic, semi-automatic or manual mode - by GSE autoleveling system to detect and follow aircraft vertical movements
2015-04-28
WIP Standard
AIR6892
This SAE Aerospace Information Report (AIR) is applicable to rotorcraft structural health monitoring (SHM) applications, both commercial and military, where end users are seeking guidance on the definition, development, integration, qualification, and certification of SHM technologies to achieve enhanced safety and reduced maintenance burden based on the lessons learned from existing Health and Usage Monitoring Systems (HUMS). While guidance on SHM business case analysis would be useful to the community, such guidance is beyond the scope of this AIR. For the purpose of this document, SHM is defined as “the process of acquiring and analyzing data from on-board sensors to evaluate the health of a structure.” The suite of on-board sensors could include any presently installed aircraft sensors as well as new sensors to be defined in the future. Interrogation of the sensors could be done onboard during flight or using ground support equipment.
2014-11-05
WIP Standard
ARP6887
The ARP shall cover the objectives and activities of Verification & Vallidation Processes required to assure high quality and/or criticality level of an IVHM Systems and Software.
2014-09-30
WIP Standard
AIR6334
This SAE Aerospace Information Report (AIR) examines the need for and the application of a power train usage metric that can be used to more accurately determine the TBO for helicopter transmissions. It provides a formula for the translation of the recorded torque history into mechanical usage. It provides examples of this process and recommends a way forward. This document of the SAE HM-1 IVHM Committee is not intended as a legal document and does not provide detailed implementation steps, but does address general implementation concerns and potential benefits.
CURRENT
2014-07-07
Standard
ARP6275
This ARP provides insights on how to perform a cost benefit analysis (CBA) to determine the return on investment that would result from implementing an integrated Health Management (HM) system on an air vehicle. The word “integrated” refers to the combination or “roll up” of sub-systems health management tools to create a platform centric system. The document describes the complexity of features that can be considered in the analysis, the different tools and approaches for conducting a CBA and differentiates between military and commercial applications. This document is intended to help those who might not necessarily have a deep technical understanding or familiarity with HM systems but want to either quantify or understand the economic benefits (i.e., the value proposition) that a HM system could provide.
CURRENT
2014-06-24
Standard
AS8091A
This SAE Aerospace Standard (AS) provides requirements for design and installation of aircraft jacking pad adapters and the mating jack socket interface to permit use of standard jacking equipment to be used in civil and military transport aircraft. The adapter defined herein shall be the key interface between the aircraft and the aircraft jack(s).
CURRENT
2014-05-29
Standard
AIR1375D
This document applies to special purpose equipment which is used in the ground handling, servicing, and maintenance of transport aircraft. Fixed airport facilities and equipment covered under other sections of Part 1910 of Code of Federal Regulations (OSHA) are excluded from the scope of this document.
CURRENT
2014-03-11
Standard
AIR4652A
This SAE Aerospace Information Report (AIR) covers handicapped passenger boarding devices used airside to transfer handicapped passengers between the terminal building and the aircraft. It provides an elevating platform to facilitate access to the aircraft; it does not cover devices for in-terminal or streetside transfers, wheelchairs for on-board aircraft or in-terminal usage, or aircraft boarding bridges. However, it should be recognized that for many handicapped passengers, a boarding chair is necessary for the lifting operation and movement to the passenger's seat inside the aircraft cabin. Such wheelchairs are widely used in larger aircraft, and the Federal Aviation Agency has developed a performance specification for a boarding chair for commuter aircraft.
CURRENT
2014-03-11
Standard
ARP5141A
This SAE Aerospace Recommended Practice (ARP) is intended to recommend a minimum standard, for the design and manufacturer of a self-propelled, chassis mounted passenger boarding vehicle. The vehicle will permit safe operation while minimizing aircraft damage and personnel safety hazards associated with commercial aircraft boarding operations. The vehicle described is intended to be used for assisting wheelchair passengers and passengers with disabilities on and off aircraft with door sill heights of 60 in (152.4 cm) and above.
CURRENT
2014-03-11
Standard
ARP5140A
This SAE Aerospace Recommended Practice (ARP) outlines the design and functional requirements for aircraft passenger lifts, operated manually and self-propelled. The primary function of the lift described in this document is to act as an elevator between ground level and aircraft doorsills to a maximum of 144 in.
Viewing 1 to 30 of 177

Filter

  • Standard
    177