Criteria

Text:
Topic:
Content:
Display:

Results

Viewing 1 to 30 of 1094
2017-12-11
WIP Standard
J2568
This SAE Recommended Practice specifies an intrusion resistance test method for glazing systems installed in motor vehicles. Intrusion resistance performance is determined not solely by the glazing but also by the glazing attachment to the vehicle and by the vehicle structure. Therefore, the glazing/ attachment/vehicle structure must be tested as a single unit. This test determines intrusion resistance only. The test applies to those materials that meet the requirements for use as safety glazing materials as specified in Safety Standard ANSI/SAE Z26.1 or other applicable standards. The test applies to all installation locations.
CURRENT
2017-11-20
Standard
J587_201711
This SAE Standard provides test procedures, requirements, and guidelines for vehicular license plate illumination devices.
2017-11-20
WIP Standard
J3014
This SAE Recommended Practice provides test procedures, requirements, and equipment recommendations for the methods of the measurement that characterizes potential design failures by utilizing a step stress approach to subject a device under test to thermal, vibration, and electrical stresses of types and levels beyond what it may see in actual use, but which will rapidly induce failure modes, allowing them to be detected and corrected.
CURRENT
2017-11-16
Standard
J3003_201711
This SAE Recommended Practice provides dimensional specifications for the 41/2 and 53/4 inch general service sealed lighting units, intended for use in such applications as motorcycle headlamps, military headlamps, industrial machinery headlamps, fog lamps, spot lamps, etc. See Figures 1 and 2 and Tables 1 and 2.
CURRENT
2017-11-09
Standard
ARP991C
This document recommends design objectives for navigation, position, and anticollisionlight systems for visual detection and collision avoidance between airplanes in flight and on the ground. Customers for new airplanes or lighting components, and designers or manufacturers may take advantage of this document in specifying the initial requirements that, in most cases, significantly exceed the applicable minimum intensities as shown in the Federal Aviation Regulations as well provide better stability, longer life and lower operating costs.
2017-10-16
WIP Standard
J2838
This SAE standard provides test procedures, performance requirements, design guidelines and installation guidelines for full adaptive forward lighting systems (AFS).
CURRENT
2017-10-10
Standard
J95_201710
This SAE Standard provides performance and general design requirements and related test procedures for headlamps for use on industrial wheeled equipment that may be operated on public roads.
CURRENT
2017-09-19
Standard
J2527_201709
This SAE Standard specifies the operating procedures for a controlled irradiance, xenon-arc apparatus used for the accelerated exposure of various exterior automotive materials.
CURRENT
2017-09-15
Standard
J2938_201709
This SAE Recommended Practice provides the methods of measurements for electrical and photometric characteristics of LED packages. It provides procedures, requirements, and guidelines for the methods of the measurement of luminous flux and color maintenance of LED devices (packages, arrays, and modules) for ground vehicle lighting applications.
CURRENT
2017-09-13
Standard
ARP5637A
The information in this document is intended to apply to commercial jet transport category airplanes that incorporate plastic (polycarbonate or acrylic) lenses on exterior light assemblies, or are being considered for such an application as opposed to glass lens designs. Exterior lighting applications include position light assemblies, anticollision light asemblies, and landing light assemblies. However, much of the material provided herein is general in nature and is directly applicable to many aircraft categories including, but not limited to, helicopters, general aviation aircraft, and military aircraft.
2017-09-12
WIP Standard
J578
This SAE Standard defines and provides a means for the control of colors employed in motor vehicle external lighting equipment, including lamps and reflex reflectors. The document applies to the overall effective color of light emitted by the device in any given direction and not to the color of the light from a small area of the lens. It does not apply to pilot, indicator, or tell-tale lights.
CURRENT
2017-09-08
Standard
ARP6253A
This document presents minimum criteria for the design and installation of LED assemblies in aircraft. The use of "shall" in this specification expresses provisions that are binding. Nonmandatory provisions use the term "should."
2017-09-07
WIP Standard
J96
This SAE Standard covers the general requirements and the test requirements for a flashing warning lamp for industrial wheeled equipment.
CURRENT
2017-08-24
Standard
AS8017D
This SAE Aerospace Standard (AS) establishes minimum performance standards for new equipment anticollision light systems. This Aerospace Standard defines minimum light intensity in terms of "effective intensity" as defined in paragraph 3.5 of this standard and specified vertical and horizontal directions about the longitudinal and vertical axis of the airplane. It will also define flash rate and color for the anticollision light system. It is not intended that this standard require the use of any particular light source such as Xenon, LED or any other specific design of lamp.
CURRENT
2017-08-24
Standard
ARP4168B
This ARP covers three common light sources, incandescent, electroluminescent and light emitting diode that, when NVG filtered, can be used to illuminate NVG compatible aerospace crew stations. It is recognized that many other different light sources can also be used for this purpose. Also see 2.1.1 for other SAE documents that cover particular applications within the crew station environment. This ARP sets forth recommendations for the design of NVG compatible lighting, utilizing these light sources, that will meet the requirements of MIL-L-85762 Lighting, Aircraft, Interior, Night Vision Imaging System (NVIS) Compatible. This also includes the replacement document MIL-STD-3009: Lighting, Aircraft, Night Vision Imaging System (NVIS) Compatible. Although this ARP concentrates on lamp light sources for illumination, the information contained within this ARP may be directly applied to incandescent, electroluminescent and light emitting diode information display devices.
2017-08-22
WIP Standard
J2357
This SAE Recommended Practice is intended as a guide toward standard practice and is subject to change to keep pace with experience and technical advances. This document establishes performance requirements, design requirements and design guidelines for electronic devices.
CURRENT
2017-08-17
Standard
J2087_201708
This SAE Standard provides test procedures, requirements, and guidelines for a daytime running light (DRL) function.
CURRENT
2017-08-07
Standard
J576_201708
This SAE Recommended Practice is intended as a guide toward standard practice and is subject to change to keep pace with experience and technical advances. This document establishes additional performance requirements and provides test methods and requirements to evaluate the suitability of plastic material or materials intended for optical applications in motor vehicles. The tests are intended to determine physical and optical characteristics of the material or materials only. Performance expectations of finished assemblies, including plastic components, are to be based on tests for lighting devices, as specified in SAE Standards and Recommended Practices for motor vehicle lighting equipment.
2017-07-20
WIP Standard
ARP5873B
This document presents minimum criteria for the design and installation of LED passenger reading light assemblies in commercial aircraft. The use of “shall” in this specification expresses provisions that are binding. Non-mandatory provisions use the term “should.”
2017-07-12
WIP Standard
J759
This SAE Recommended Practice provides the lighting function identification codes for use on all passenger vehicles, trucks, trailers, motorcycles, and emergency vehicles.
CURRENT
2017-07-11
Standard
J852_201707
This SAE Recommended Practice provides test procedures, performance requirements, and guidelines for front cornering lamps intended for use on motor vehicles.
2017-06-28
WIP Standard
J3145
This SAE Recommended Practice is intended as a guide for specifying LED Substitute Light Sources as Equivalents for corresponding RID filament light sources and is subject to change to keep pace with experience and technical advances. This document defines criteria for technical equivalence in order to make a substitution of a filament light source with an LED light source without compromising the performance of the RID device.
CURRENT
2017-06-09
Standard
J2999_201706
This SAE Standard provides a method for determining the Effective Projected Luminous Lens Area (EPLLA) of a lamp function using design analysis. This standard was created to clarify and address how to determine EPLLA with traditional and new technologies.
CURRENT
2017-06-09
Standard
J3098_201706
This SAE Recommended Practice applies to a decorative lamp(s) installed on the front of motor vehicles. This lamp(s) is intended only to be decorative and is not to impair the effectiveness of any required lighting device. This recommended practice establishes uniformity in use guidelines for the performance, installation, activation and switching of a front decorative lamp(s).
CURRENT
2017-05-25
Standard
AIR805D
Information in this report is applicable to design and development of aircraft jet blast windshield rain removal systems.
CURRENT
2017-05-19
Standard
J2591_201705
This SAE Recommended Practice applies to motor vehicle Forward Illumination Devices which incorporate limited adaptive beam pattern capabilities. This document is to be used in conjunction with other forward lighting standards and/or recommended practices which define the base beam procedures, requirements, and guidelines.
2017-05-09
WIP Standard
J2042
This SAE Standard provides test procedures, requirements, and guidelines for clearance, sidemarker, and identification lamps intended for use on vehicles 2032 mm or more in overall width. A clearance lamp, sidemarker lamp, or an identification lamp conforming to the requirements of this document may be used on vehicles less than 2032 mm in overall width.
CURRENT
2017-05-09
Standard
ARP5297B
This SAE Aerospace Recommended Practice (ARP) provides the qualification test procedure requirements for low wattage halogen lamps (less than 35 watts) intended for use primarily in aircraft applications. The purpose of these tests is to provide a laboratory means of determining the performance characteristics of lamps under airplane power and other environmental conditions and to verify the integrity of the lamp design and production processes.
2017-04-24
WIP Standard
J1330
The purpose of this SAE Information Report is to list and explain major equipment, instrumentation, and procedure variables which can affect inter-laboratory differences and repeatability of photometric measurements of various lighting devices listed in SAE Technical Reports. The accuracy guidelines listed in the report are for the purpose of controlling variables that are not a direct function of the lighting device being measured. The control of these individual variables is necessary to control the overall accuracy of photometric measurements. These accuracy guidelines apply to the measurement of the luminous intensities and reflected intensities of devices at the specified geometrically distributed test points and areas. These guidelines do not apply to photometric equipment used to measure license plate lamps.
CURRENT
2017-04-17
Standard
J361_201704
This SAE Recommended Practice applies to parts and materials used in vehicle manufacture which are intended to be acceptable color matches to a specified standard. This document is intended for use with parts or materials which are opaque or nearly so. Materials covered by this document include topcoat paint finishes, interior soft trim, interior and exterior hard trim, and exterior film and flexible trim. This practice requires judgments by observers with a minimum of normal color vision and preferably superior as rated with the FM-100 Hue Test as specified in ASTM E1499, Guide for Selection, Evaluation, and Training of Observers.
Viewing 1 to 30 of 1094