Display:

Results

Viewing 1 to 30 of 2025
2017-09-04
Technical Paper
2017-24-0009
Federico Millo, Giulio Boccardo, Andrea Piano, Luigi Arnone, Stefano Manelli, Giuseppe Tutore, Andrea Marinoni
To comply with TIER IV emission standard, Kohler Engines has developed the 100kW rated KDI 3.4 liters diesel engine, equipped with DOC and SCR. Based on this engine, a research project in collaboration between Kohler Engines and Politecnico di Torino has been carried out to exploit the potential of new technologies to meet the TIER IV and beyond emission standards. The prototype engine was equipped with a low pressure cooled EGR system, two stage turbocharger, high pressure fuel injection system capable of very high injection pressure and DOC+DPF aftertreatment system. Since the TIER IV emission standard sets a 0.4g/kWh NOx limit for the NRSC steady state test cycle, that includes full load operating conditions, the engine must be operated with very high EGR rates (above 30%) at very high load. As a consequence, the low air to fuel ratio and the risk of high soot emissions must be handled by means of high fuel injection pressure and proper injection patterns.
2017-09-04
Technical Paper
2017-24-0135
Shuxia Miao, Lin Luo, Yan Liu, Zhangsong Zhan
New emissions regulations of light-duty vehicles (China 6) will be implemented in China from July 1, 2020. This standard includes two stages, China 6a and China 6b, in which the PM limits of 4.5 mg/km and 3.0 mg/km are introduced respectively, the PN limit is set to be 6×10e11 #/km for both stages. The WLTC testing cycle will be implemented in China 6 regulation as well. In this study a light-duty vehicle satisfying China 6(b) emission standards was developed by improving the engine raw emissions, optimizing the calibration and adding a coated GPF to the after-treatment system. The impacts of ash content and consumption of engine oil and the fast ash accumulation to vehicle emissions and backpressure were analyzed through dynamometer testing. The vehicle after-treatment system was then designed and developed to meet China 6(b) emission standards. The characteristics of soot accumulated through mimicking routine driving under cold environments were tested.
2017-09-04
Technical Paper
2017-24-0091
Hyun Woo Won, Alexandre Bouet, Joseph KERMANI, Florence Duffour
Reduce the CO2 footprint, limit the pollutant emissions and rebalance the ongoing shift demand toward middle-distillate fuels are major concerns for vehicle manufacturers and oil refiners. In this context, gasoline-like fuels have been recently identified as good candidate. Strait run naphtha, a refinery stream directly derived from the atmospheric crude oil distillation process, allows to reduce both NOx and particulate emissions when used in compression-ignition engines. CO2 benefits are also expected thanks to its higher H/C ratio and energy content compared to diesel. In previous studies, wide ranges of Cetane Number naphtha fuels have been evaluated and CN 35 naphtha fuel has been selected. The assessment and the choice of the required engine hardware adapted to this fuel, such as the compression ratio, bowl pattern, nozzle design and air-path technology have been performed on a light-duty single cylinder compression-ignition engine.
2017-07-10
Technical Paper
2017-28-1937
Jyotirmoy Barman, Prateek Arora, Kumar Patchappalam
Abstract Air Pollution is a major concern in our country due to which Indian Government has taken a decision to move from BS-IV to BS-VI which is nearly 90% reduction in NOx and 50% in particulate matter along with addition of particulate number regulation for BS-VI in comparison to BS-IV norms in very short span of time. Vehicle manufacturers are also having the challenge to produce low cost and fuel efficient product with BS-VI solution in order to meet tightening emission regulations and increasing needs of lower fuel consumption. Detailed study is done with different approaches to meet BS-VI emission which is elaborately explained in different aspect of engine design and after treatment parameter with its pros and cons. After Treatment selection plays an important role in engine development to meet stringent emission legislations and customer demands. Strategies for BS-VI were described with the advantage and drawbacks for after treatment selection.
2017-07-10
Technical Paper
2017-28-1933
Alberto Boretti
Abstract The paper captures the recent events in relation with the Volkswagen (VW) Emissions Scandal and addresses the impact of this event on the future of power train development. The paper analyses the impact on the perspectives of the internal combustion engine, the battery based electric car and the hydrogen based technology. The operation of the United States Environmental Protection Agency (EPA), VW and the United States prosecutor, sparked by the action of the International Council on Clean Transportation (ICCT) is forcing the Original Equipment Manufacturers (OEM) towards everything but rationale immediate transition to the battery based electric mobility. This transition voids the value of any improvement of the internal combustion engine (ICE), especially in the lean burn, compression ignition (CI) technology, and of a better hybridization of powertrains, both options that have much better short term perspectives than the battery based electric car.
2017-05-10
Technical Paper
2017-01-1925
Lukas Walter, Attila Toth, Gernot Hasenbichler, Helmut Theissl, Russ Truemner, Gregory Heimann, Praveen Rastogi
With the implementation of EURO VI and similar emission legislation, the industry assumed the pace and stringency of new legislation would be reduced in the future. The latest announcements of proposed and implemented legislation steps show that future legislation will be even more stringent. The currently leading announced legislation, which concerns a large number of global manufacturers, is the legislation from the United States (US) Environmental Protection Agency (EPA) and the California Air Resources Board (CARB). Both announced new legislation for CO2, Greenhouse Gas (GHG) Phase II. CARB is also planning additional Ultra Low NOx regulations. Both regulations are significant and will require a number of technologies to be used in order to achieve the challenging limits. AVL published some engine related measures to address these legislation steps.
2017-03-28
Technical Paper
2017-01-0169
Ward J. Atkinson, William Raymond Hill, Gursaran D. Mathur
Abstract The EPA has issued regulations in the Final Rulemaking for 2017-2025 Light-Duty Vehicle Greenhouse Gas Emission Standards and Corporate Average Fuel Economy Standards (420r12901-3). This document provides credits against the fuel economy regulations for various Air Conditioning technologies. One of these credits is associated with increased use of recirculation air mode, when the ambient is over 24°C (75°F.). The authors want to communicate the experiences in their careers that highlighted issues with air quality in the interior of the vehicle cabin. Cabin contamination sources may result in safety and health issues for both younger and older drivers. Alertness concerns may hinder their ability to operate a vehicle safely.
2017-03-28
Technical Paper
2017-01-0872
Sunil Kumar Pathak, Vineet sood, Yograj Singh, Shubham Gupta, Salim Abbasbhai Channiwala
Abstract In this study, A Gasoline Passenger car (Euro IV) was experimentally investigated for performance and emissions on three different fuels i.e. Gasoline, LPG (Liquefied Petroleum Gas) and DME (Di-methyl ether) blend with a concentration of 20% by mass in LPG (DME20). In particular, emission characteristics (including Hydrocarbon, CO, NOx, and CO2) over the Modified Indian Driving Cycle (MIDC) and fuel economy were investigated at the Vehicle Emission Laboratory (VEL) at the CSIR- Indian Institute of Petroleum, Dehradun, India. The experimental results showed that Vehicle complies with Euro IV legislation on gasoline and LPG fuel, however, showed higher NOx Emissions on DME 20 fuel. LPG kit was reconfigured for DME and LPG blend to bring down the emissions within the specified emission limits. The Emission values observed for DME20 were 0.635 g/km (CO), 0.044 g/km (THC), and 0.014 g/km (NOx) against the Euro IV limits of 1.0 g/km, 0.1 g/km and 0.08 g/km, respectively.
2017-03-28
Technical Paper
2017-01-1016
Charles Schenk, Paul Dekraker
Abstract EPA has been benchmarking engines and transmissions to generate inputs for use in its technology assessments supporting the Midterm Evaluation of EPA’s 2017-2025 Light-Duty Vehicle greenhouse gas emissions assessments. As part of an Atkinson cycle engine technology assessment of applications in light-duty vehicles, cooled external exhaust gas recirculation (cEGR) and cylinder deactivation (CDA) were evaluated. The base engine was a production gasoline 2.0L four-cylinder engine with 75 degrees of intake cam phase authority and a 14:1 geometric compression ratio. An open ECU and cEGR hardware were installed on the engine so that the CO2 reduction effectiveness could be evaluated. Additionally, two cylinders were deactivated to determine what CO2 benefits could be achieved. Once a steady state calibration was complete, two-cycle (FTP and HwFET) CO2 reduction estimates were made using fuel weighted operating modes and a full vehicle model (ALPHA) cycle simulation.
2017-03-28
Journal Article
2017-01-1013
Sunil Kumar Pathak, Yograj Singh, Vineet sood, Salim Abbasbhai Channiwala
Abstract The standard emission protocol including driving cycle is performed for the legislative fuel economy and emission testing of the vehicles in a laboratory. The driving cycles are expected to represent actual driving pattern and energy requirements. However, recent studies showed that the gap between real world driving conditions and the standard driving cycle is widening, as the traffic pattern and vehicle population is varying dynamically and the change in the emission procedures is not synchronized with the same pace. More so, as the process of harmonization of emission legislations is in progress to narrow down the country specific variation of emission regulation, as this will help in the smooth globalization of the automotive business process. The new regulation for in-service conformity is being considered to reduce the emissions in real-world driving.
2017-03-28
Technical Paper
2017-01-1020
Finn Tseng, Imad Makki, Pankaj Kumar, Robert Jentz, Aed Dudar
Abstract Engine-Off Natural Vacuum (EONV) principles based leak detection monitors are designed to determine the presence of a small leak in the fuel tank system. It was introduced to address the ever more stringent emission requirement (currently at 0.02”) for gasoline engine equipped vehicles as proposed by the Environmental Protection Agency (EPA) and California Air Resources Board (CARB) in the United States [2, 3]. Other environmental protection agencies including the ones in EU and China will be adopting similar regulations in the near future. Due to its sensitivity to known noise factors such as the ambient temperature, barometric pressure, drive pattern and parking angle, it has been historically a lower performing monitor that is susceptible to warranty cost or even voluntary recalls. The proposed new model based monitor utilizes production pressure signal and newly instrumented temperature sensors [15].
2017-03-28
Journal Article
2017-01-0911
Krishna Chilumukuru, Aniket Gupta, Michael Ruth, Michael Cunningham, Govindarajan Kothandaraman, Lasitha Cumaranatunge, Howard Hess
Abstract Future light duty vehicles in the United States are required to be certified on the FTP-75 cycle to meet Tier 3 or LEV III emission standards [1, 2]. The cold phase of this cycle is heavily weighted and mitigation of emissions during this phase is crucial to meet the low tail pipe emission targets [3, 4]. In this work, a novel aftertreatment architecture and controls to improve Nitrogen Oxides (NOx) and Hydrocarbon (HC) or Non Methane Organic gases (NMOG) conversion efficiencies at low temperatures is proposed. This includes a passive NOx & HC adsorber, termed the diesel Cold Start Concept (dCSC™) catalyst, followed by a Selective Catalytic Reduction catalyst on Filter (SCRF®) and an under-floor Selective Catalytic Reduction catalyst (SCR). The system utilizes a gaseous ammonia delivery system capable of dosing at two locations to maximize NOx conversion and minimize parasitic ammonia oxidation and ammonia slip.
2017-03-28
Technical Paper
2017-01-0907
Timothy Johnson, Ameya Joshi
Abstract This review paper summarizes major and representative developments in vehicle engine efficiency and emissions regulations and technologies from 2016. The paper starts with the key regulatory developments in the field, including newly proposed European RDE (real driving emissions) particle number regulations, and Euro 6 type regulations for China and India in the 2020 timeframe. China will be tightening 30-40% relative to Euro 6 in 2023. The California heavy duty (HD) low-NOx regulation is advancing and the US EPA is anticipating developing a harmonized proposal for implementation in 2023+. The US also finalized the next round of HD GHG (greenhouse gas) regulations for 2021-27, requiring 5% engine CO2 reductions. LD (light duty) and HD engine technology continues showing marked improvements in engine efficiency. Key developments are summarized for gasoline and diesel engines to meet both the emerging criteria and greenhouse gas regulations.
2017-01-10
Technical Paper
2017-26-0230
Timothy Dallmann, Zhenying Shao, Aparna Menon, Anup Bandivadekar
Abstract Diesel engines used in non-road vehicles and equipment are a significant source of pollutant emissions that contribute to poor air quality, negative human health impacts, and climate change. Efforts to mitigate the emissions impact of these sources, such as regulatory control programs, have played a key role in air quality management strategies around the world, and have helped to spur the development of advanced engine and emission control technologies. As non-road engine emissions control programs are developed in a growing number of countries around the world, it is instructive to look at the development of programs in two of the regions that have progressed furthest in controlling emissions from non-road engines, the United States (U.S.) and European Union (EU).
2017-01-10
Technical Paper
2017-26-0124
Vikram Betageri, R Mahesh
Abstract BS VI or Euro VI Norms mandates the RDE emission compliance for the diesel commercial vehicles. Development of the engine- after treatment system for meeting these requirements needs a greater insight into the emission behavior of the vehicle under current norms i.e. BS IV and Euro V. In other words, quantifying the on road emission of current vehicle will be helpful in developing engine/vehicle for RDE emission compliance. In the current study, the focus is on the assessment of real road NOx emission of a BS IV and Euro V complaint diesel commercial vehicle. The real road emissions of vehicle have been quantified using the onboard NOx sensor mounted on the after treatment system outlet along with a validated exhaust gas model developed and parameterized in engine control unit. The real road NOx emissions were compared with the test bench emissions for various conditions.
2017-01-10
Technical Paper
2017-26-0125
Sougato Chatterjee, Mojghan Naseri, Jianquan Li
Abstract The next generation advanced emission regulations have been proposed for the Indian heavy duty automotive industry for implementation from 2020. These BS VI emission regulations will require both advanced NOx control as well as advanced PM (Particulate Matter) control along with Particle Number limitations. This will require implementation of full DPF (Diesel Particulate Filter) and simultaneous NOx control using SCR technologies. DPF technologies have already been successfully implemented in Euro VI and US 10 HDD systems. These systems use low temperature NO2 based passive DPF regeneration as well as high temperature oxygen based active DPF regeneration. Effective DPF and DOC designs are essential to enable successful DPF regeneration (minimize soot loading in the DPF) while operating HDD vehicles under transient conditions. DOC designs are optimized to oxidize engine out NO into NO2, which helps with passive DPF regeneration.
2017-01-10
Technical Paper
2017-26-0126
Steve Golden, Zahra Nazarpoor, Ru-Fen Liu
Abstract In the context of evolving market conditions, the three-way catalyst (TWC) design is entering an exciting new phase. It remains the main emission control strategy for gasoline powered vehicles in the broad context of evolving engine technology; the move to more real-world, transient testing and much tighter tailpipe emissions regulations. The specific context here is the launch of BSVI regulations for gasoline passenger cars in India. The key approach described here is to achieve highly beneficial emission performance based on low PGM levels with the emphasis on new materials technology to significantly alter the functional balance between PGM and “promoters”. We will focus on the design of materials with the spinel structure and have developed catalyst products that synergize low levels of PGM (so-called SPGM) leveraging the key properties of the advanced spinel oxides.
2017-01-10
Technical Paper
2017-26-0128
Om Parkash Bhardwaj, Ketan Krishnamurthy, David Blanco-Rodriguez, Bastian Holderbaum, Thomas Körfer
Abstract Despite the trend in increased prosperity, the Indian automotive market, which is traditionally dominated by highly cost-oriented producion, is very sensitive to the price of fuels and vehicles. Due to these very specific market demands, the U-LCV (ultra-light commercial vehicle) segment with single cylinder natural aspirated Diesel engines (typical sub 650 cc displacement) is gaining immense popularity in the recent years. By moving to 2016, with the announcement of leapfrogging directly to Bharat Stage VI (BS VI) emission legislation in India, and in addition to the mandatory application of Diesel particle filters (DPF), there will be a need to implement effective NOx aftertreament systems. Due to the very low power-to-weight ratio of these particular applications, the engine operation takes place under full load conditions in a significant portion of the test cycle.
2017-01-10
Journal Article
2017-26-0116
Mahesh Govindareddy, Achim Heibel
Abstract With Bharat Stage VI (BSVI) regulations on the horizon [3],[4]tighter particulate matter (PM) regulations will require the use of wall flow diesel particulate filters for on-road heavy duty (HD) diesel engines in India. The Indian HD vehicle market is very cost sensitive, especially with the majority of engine displacement being less than 7L [5] therefore, after treatment cost plays a significant role in design of the system. Robust wall flow diesel particulate filter solutions with the ability to deliver high filtration requirements required for particle number regulations can be designed in a cost-efficient manner. In this paper advanced design for diesel particulate filters with pressure drop, ash capacity, regeneration, and filtration performance are discussed. Corning’s asymmetric cell technology (ACT) was created to improve ash capacity and reduce pressure drop and has the potential to downsize up to 45%.
2017-01-10
Technical Paper
2017-26-0118
Satoshi Sumiya, David Bergeal, Kenan Sager
Abstract The Indian government has announced that India will skip BS V legislation and move to BS VI from 2020. In order to meet this NOx emission standard, most vehicles will need to adopt either NOx Storage Catalyst (NSC) or Selective Catalytic Reduction (SCR). It is shown that these two devices have different NOx reduction temperature windows and different sulfur tolerance. In the LDD application, it is highly important to deal with NOx in the low temperature region directly after a cold start. NSC works in this region with better performance than SCR, but its sulfur tolerance is weaker than SCR. To improve the weakness in low temperature NOx control on SCR, SCRF® which is SCR coated Diesel Particulate Filter (DPF) was developed and it demonstrated an advantage in light-off performance, due to the advantage in temperature conditions, by minimizing heat loss upstream of the SCR device.
2017-01-10
Technical Paper
2017-26-0117
Matti A Harkonen, Alok Trigunayat, Arvind Kumar, Bosco Rajan
Abstract Light Duty Vehicles (LDVs), typically with engine displacement volume of less than 1.5L are an integral part of the India’s automobile sector as they are one of the most preferred means of transportation in rural as well as urban India. This market has always been on the rise as a result of rising population, growing commercialization, increasing commercial activities, etc. which are all contributing to the increased demand for intra city transportation. The passenger LDVs such as the three wheeler segment dominates the market as the need for affordable passenger commutation is higher than the need for goods carriage within a city. With BS VI norms slated to be implemented in 2020, it becomes imperative to understand, plan and work out strategies to meet these norms effectively on the Indian roads & actual Indian driving behavior, especially for these LDVs.
2017-01-10
Technical Paper
2017-26-0120
Kevin Hallstrom, Sandip D. Shah
Abstract The legislative decision to accelerate the implementation of regulations requiring advanced emissions control in India have accelerated the need to advanced emissions control systems. Particulate filters and NOx abatement technology will be needed to meet the new BSVI standards. Integration of these emission control technologies into engine design poses new challenges to the Indian Heavy Duty Diesel Truck Industry. Each new market that implements advanced emission regulations faces challenges that are unique to the local regulation, the local vehicle design, and the local operating conditions. This paper will review the technology options available for BSVI, their strengths and weaknesses, and potential system designs. Additionally this paper will review how critical design factors such as filter regeneration conditions, duty cycle temperatures, and urea injection can affect the system design and catalyst selection.
2017-01-10
Journal Article
2017-26-0119
Ragupathi Soundara Rajan, Vijay Sharma, Ashraf Emran, Devising Rathod, John Henry Kwee, Thorsten Michaelis-Hauswaldt, Thomas Körfer
Abstract The emission legislations are becoming increasingly strict all over the world and India too has taken a big leap in this direction by signaling the migration from Bharat Stage 4 (BS 4) to BS 6 in the year 2020. This decision by the Indian government has provided the Indian automotive industry a new challenge to find the most optimal solution for this migration, with the existing BS 4 engines available in their portfolio. Indian market for the LCV segment is highly competitive and cost sensitive where the overall vehicle operation cost (vehicle cost + fluid consumption cost) is the most critical factor. The engine and after-treatment technology for BS 6 emission levels should consider the factors of minimizing the additional hardware cost as well as improving the fuel efficiency. Often both of which are inversely proportional. The presented study involves the optimization of after treatment component size, layout and various systems for NOx and PM reduction.
2017-01-10
Technical Paper
2017-26-0043
Peter Heuser, Stefano Ghetti, Devising Rathod, Sebastian Petri, Sascha Schoenfeld
Abstract The Bharat Stage VI (BS-VI) emission legislation will come into force in 2020, posing a major engineering challenge in terms of system complexity, reliability, cost and development time. Solutions for the EURO VI on-road legislation in Europe, from which the BS-VI limits are derived, have been developed and have already been implemented. To a certain level these European solutions can be transferred to the Indian market. However, several market-specific challenges are yet to be defined and addressed. In addition, a very strict timeline has to be considered for application of advanced technologies and processes during the product development. In this paper, the emission roadmap will be introduced in the beginning, followed by a discussion of potential technology solutions on the engine itself as well as on the exhaust aftertreatment side. This includes boosting and fuel injection technologies as well as different exhaust gas recirculation methods.
2017-01-10
Technical Paper
2017-26-0042
Subhanker Dev, Hitesh B Chaudhari, Sanjeev Gothekar, Simhachalam Juttu, Nagesh Harishchandra Walke, Neelkanth V Marathe
Abstract With the announcement, as per draft notification GSR 187 (E) dated 19th Feb 2016 issued by MoRTH (Ministry of Road Transport and Highways), on vehicle emission standards to leapfrog from BS IV to BS VI by 2020, diesel engines would be greatly facing challenges to meet the stringent emission requirements of 90% reduction in PM and 50% reduction in NOx emissions simultaneously. Up to BS IV, in-cylinder strategies utilizing higher fuel injection pressure, higher intake boost, lower to moderate EGR, optimized combustion chamber design and lower intake manifold temperature would be sufficient. But meeting emission levels at BS VI levels would require a combination of both in-cylinder combustion control and after treatment system [1]. However, unlike Europe and US markets where wide spread adoption of after treatment solution is viable, for Indian market it would be impeded by infrastructure availability, system cost and cost of ownership.
2017-01-10
Journal Article
2017-26-0056
Suramya Naik, David Johnson, Laurence Fromm, John Koszewnik, Fabien Redon, Gerhard Regner, Neerav Abani
Abstract The government of India has decided to implement Bharat Stage VI (BS-VI) emissions standards from April 2020. This requires OEMs to equip their diesel engines with costly after-treatment, EGR systems and higher rail pressure fuel systems. By one estimate, BS-VI engines are expected to be 15 to 20% more expensive than BS-IV engines, while also suffering with 2 to 3 % lower fuel economy. OEMs are looking for solutions to meet the BS-VI emissions standards while still keeping the upfront and operating costs low enough for their products to attract customers; however traditional engine technologies seem to have exhausted the possibilities. Fuel economy improvement technologies applied to traditional 4-stroke engines bring small benefits with large cost penalties. One promising solution to meet both current, and future, emissions standards with much improved fuel economy at lower cost is the Opposed Piston (OP) engine.
2017-01-10
Technical Paper
2017-26-0137
Marco Schöggl, Ernst-Georg Lorinser
Abstract With the official publication of the “RDE package 1” on 31st March 2016 the long awaited start of RDE testing is now fixed. This event marks a milestone in the emission legislation for passenger cars and is the first of a series of four RDE packages to fade-in real world testing of passenger cars in Europe. During the same time India announced in the Gazette of India on 19th February, 2016 - G.S.R. 187(E). - the draft of introduction of Bharat VI by April 1st 2020 [5] which also should include the Real Driving Emissions (RDE) on-road certification as per procedure laid down in AIS137 and as amended from time to time. As European RDE legislation will be the baseline for Indian RDE legislation rules this paper will highlight the differences and challenges expected between the requirements in Europe compared to India during the first tests done by AVL Technical Center Private Limited located in Gurgaon.
2017-01-10
Journal Article
2017-26-0138
B Sakthivel, R Sridhar, Subin Ansh, B Srinivasan, J Suresh Kumar
Abstract The air pollution is increasing at an alarming rate now a day mainly due to emissions coming out of automotive vehicles. The exhaust emissions gases are hazardous to human health. The increased number of vehicles on road will make the scenario even worse. In order to control the pollution level, the regulatory bodies are now implementing stringent emission norms. In India, the regulatory authorities has framed the transition of BS IV to BS VI emission norms in 2020 by skipping the BS V emission norms which makes the automotive industries to work on more advanced fuel management technologies. It is more tedious to control the tail pipe emissions beyond BS IV emission norms with the conventional carburetor system since it is operating on open loop system.
2017-01-10
Technical Paper
2017-26-0147
Stefan Lueckenbach, Uwe Moser, Bernd Haake, Johannes Frank
Abstract The decision to leapfrog from the Bharat Stage (BS) IV emission standards directly to the BS VI standards not only effects passenger and commercial vehicles but also India’s by far largest vehicle class, with regards to sales and production, the two-wheelers. The BS VI norm will not only tighten the emission standards, but it will also increase the required emission mileage level and upgrade the On-Board Diagnostic (OBD) requirements, also by introducing In-Use Monitor Performance Ratio (IUMPR) standards. While OBD was already introduced for passenger and commercial vehicles with BS IV in 2010, OBD will be then newly introduced for two-wheelers.
2016-10-25
Technical Paper
2016-36-0167
Fábio Coelho Barbosa
Abstract Emissions from motor vehicles have been a subject of concern in urban areas, as great amounts of population have been permanently exposed to large amounts of pollutants, with intrinsic adverse health effects. In this context, in the last two decades, stringent emissions standards have been developed to control the maximum emission limits of the so called regulated pollutants. This continuous reduction of emission targets has imposed a great effort to engine and vehicle manufacturer in the development of technological solutions for emission limits compliance, which can be done by reducing engine-out emissions through improvements in combustion process and fuel management system, as well as by using aftertreatment devices in the exhaust system.
Viewing 1 to 30 of 2025

Filter