Criteria

Text:
Topic:
Content:
Display:

Results

Viewing 1 to 30 of 50
CURRENT
2017-03-17
Standard
J1455_201703
The scope of this Recommended Practice encompasses the range of environments which influence the performance and reliability of the electronic equipment designed for heavy duty on and off road vehicles, as well as any appropriate stationary applications which also use these vehicle derived components. A few examples of such vehicles are on and off highway trucks, trailers, buses, construction equipment, and agricultural equipment including implements.
CURRENT
2015-10-08
Standard
J3078/6_201510
SAE J3078/6 specifies a test method for simulating solar heating in the laboratory and measuring the radiant heat energy from a natural or simulated source. It is applicable to Off-Road Self-Propelled Work Machines as defined in SAE J1116 and Agricultural Tractors as defined in ANSI/ASAE S390.
CURRENT
2015-01-23
Standard
J551/1_201501
This SAE Standard covers the measurement of radio frequency radiated emissions and immunity. Each part details the requirements for a specific type of electromagnetic compatibility (EMC) test and the applicable frequency range of the test method. The methods are applicable to a vehicle, boat, machine or device powered by an internal combustion engine or battery powered electric motor. Operation of all engines or motors (main and auxiliary) of a vehicle, boat, machine or device is included. All equipment normally operating when the vehicle, boat, machine or device is in operation is included. Operator controlled equipment is included or excluded as specified in the individual document parts. As a special case, CISPR 12 applies to battery powered floor finishing equipment, but robot carpet sweepers are excluded. By reference, IEC CISPR 12 and CISPR 25 are adopted as the standards for the measurement of vehicle emissions.
CURRENT
2014-11-24
Standard
J2698_201411
This SAE Recommended Practice covers the design and application of primary on-board wiring distribution system harnessing for surface vehicles. This document is intended for single phase nominal 120 VAC circuits that provide power to truck sleeper cab hotel loads so that they may operate with the main propulsion engine turned off. The power supply comes from alternative sources such as land-based grid power, DC-AC inverters and auxiliary power generators. The circuits may also provide power to improve vehicle performance through charging batteries or operating cold-weather starting aids.
2014-02-04
WIP Standard
J1777
This Hydrospace Information Report (HIR) identifies the general environmental considerations for the design, development, evaluation, and testing of advanced surface craft, submersible vehicles, and other marine craft. This HIR provides criteria on the environmental limits within which marine vehicles, related components, and associated equipment should operate satisfactorily and reliably. This HIR is intended for use as a guide for the development of specific environmental requirements to be included in detailed specifications for marine vehicles and associated equipment. Specific requirements are in a state of continual change as our knowledge of the ocean environment increases. The ocean environment varies with location and time. Changes in the ocean environment can occur not only on a seasonal basis but also monthly, weekly, daily, and in some cases even hourly.
2013-10-01
WIP Standard
J1533
This SAE Recommended Practice establishes a uniform test procedure for determining performance levels of operator enclosure panel type air filters on off-road, self-propelled work machines used in construction, general-purpose industrial, agriculture, and forestry as defined in SAE J1116 and equipped with an operator enclosure with a powered fresh air system.
CURRENT
2013-09-25
Standard
J1111_201309
This SAE Standard characterizes grapple skidders and identifies the major components and parts most commonly associated therewith. Illustrations used herein are not intended to include all existing commercial machines or to be exactly descriptive of any particular machine. They have been included to facilitate application of this document
2013-07-02
WIP Standard
J2333
This SAE Recommended Practice identifies and examines the various parameters which must be considered in selecting hydraulic systems filters, their locations within the system and the dirt capacity of the filter elements. This document is generally applicable to all ship hydraulic systems but does not apply to personal or recreational watercraft.
2013-06-28
WIP Standard
J1332
The purpose of this recommended practice is to establish the minimum performance requirements for devices used to indicate to the crane operator by visual, audible, or tactile means the movement of a rope drum. This SAE Recommended Practice applies to cranes when used in lifting crane service which are equipped with rope drum rotation indicating devices.
CURRENT
2013-05-31
Standard
J2333_201305
This SAE Recommended Practice identifies and examines the various parameters which must be considered in selecting hydraulic system filters, their locations within the system and the dirt capacity of the filter elements.
CURRENT
2013-05-31
Standard
J2321/3_201305
This specification sheet establishes requirements for high collapse pressure configuration filter elements of several configurations with a minimum filtration ratio of 75 for particles larger than 10 µm when designed and tested in accordance with SAE J2321 and this specification sheet.
CURRENT
2013-05-31
Standard
J2321/2_201305
This specification sheet establishes requirements for a high collapse pressure configuration filter element of a specific configuration with a minimum filtration ratio of 75 for particles larger than 7 µm when designed and tested in accordance with SAE J2321 and this specification sheet.
CURRENT
2013-05-31
Standard
J2321/1_201305
This specification sheet establishes requirements for low collapse pressure elements of a specific configuration with various efficiency ratings designed and tested in accordance with SAE J2321 and the requirements of this specification sheet.
CURRENT
2012-05-02
Standard
J1180_201205
This SAE Recommended Practice applies to mobile cranes when used in lifting crane service which are equipped with boom length indicating devices.
CURRENT
2011-12-06
Standard
J1310_201112
The scope of this SAE Information Report is to acquaint and inform those concerned with cold weather operation of diesel-powered machines and vehicles with the selection and application of electrically powered starting aids currently available. It deals specifically with the design, function, and application of line voltage electrically powered engine preheaters and battery warmers.
CURRENT
2011-12-06
Standard
J226_201112
This SAE Standard describes electric immersion engine preheaters for use in the coolant jacket of heavy-duty and intermediate size diesel engines. This document gives the dimensional information on the four basic styles of engine preheaters. The tables for each style will list the wattage commonly used. Small engines that typically require less than 600 W of preheat for cold weather starting are not covered by this document. These types of engines generally have very little space available to accommodate an immersion heater of the styles presented in this document. No related ISO standards were found.
CURRENT
2011-02-18
Standard
J2233_201102
This SAE Recommended Practice establishes uniform cold weather test procedures and performance requirements for engine coolant type heating systems of bus that are all vehicles designed to transport 10 or more passengers. The intent is to provide a test that will ensure acceptable comfort for bus occupants. It is limited to a test that can be conducted on uniform test equipment in commercially available laboratory facilities. Required test equipment, facilities, and definitions are included. There are two options for producing hot coolant in this recommended practice. Testing using these two approaches on the same vehicle will not necessarily provide identical results. Many vehicle models are offered with optional engines, and each engine has varying coolant temperatures and flow rates. If the test is being conducted to compare the performance of one heater design to another heater design, then the external coolant source approach (Test A) will yield the most comparable results.
2010-12-10
WIP Standard
J2711
This SAE Recommended Practice was established to provide an accurate, uniform and reproducible procedure for simulating use of heavy-duty hybrid- electric vehicles (HEVs) and conventional vehicles on dynamometers for the purpose of measuring emissions and fuel economy. Although the recommended practice can be applied using any driving cycle, the practice recommends three cycles: the Manhattan cycle, representing low-speed transit bus operation; the Orange County Transit Cycle, representing intermediate-speed bus operation; and the Urban Dynamometer Driving Schedule (UDDS) cycle representing high-speed operation for buses and tractor-trailers. This document does not specify which emissions constituents to measure (e.g., HC, CO, NOx, PM, CO 2 ), as that decision will depend on the objectives of the tester.
HISTORICAL
2010-12-08
Standard
J2258_201012
This SAE Standard defines requirements relating to the elements of design, operation, and maintenance of light utility vehicles. The safety specifications in this document apply to any self-propelled, operator-controlled, off-highway vehicle 1829 mm (72 in) or less in overall width, exclusive of added accessories and attachments, operable on three or more wheels, primarily intended to transport material loads or people, with a gross vehicle weight of 2500 kg (5500 lb) or less, and a maximum design speed less than or equal to 40.23 km/h (25 mph). This document is not intended to cover Go-Karts (ASTM F2007-07a), Fun-Karts (ASTM F2011-02e1), Dune Buggies, and all terrain vehicles (ATVs) complying with ANSI/SVIA 1.
HISTORICAL
2010-09-29
Standard
J2358_201009
This SAE Standard defines the safety and performance requirements for Low Speed Vehicles (“LSV”). The safety specifications in this document apply to any powered vehicle with a minimum of 4-wheels, a maximum level ground speed of more than 32 km/h (20 mph) but not more than 40 km/h (25 mph),), and a maximum gross vehicle weight of 1361 kg (3000 lb), that is intended for operating on designated roadways where permitted by law.
2010-05-06
WIP Standard
J2942
This Recommended Practice will identify the generally agreed industry approach to testing heavy-duty diesel engines under EPA's 40CFR Part 1065 regulation.
CURRENT
2007-11-16
Standard
J1332_200711
This SAE Recommended Practice applies to cranes when used in lifting crane service which are equipped with rope drum rotation indicating devices.
HISTORICAL
2007-11-15
Standard
J2641_200711
This SAE Information Report provides basic information about the issues surrounding the administration of stationary, infield sound testing of snowmobiles. The information provided herein is meant to enhance safety, improve the environment and promote uniform testing.
HISTORICAL
2007-08-22
Standard
J1111_200708
This SAE Standard characterizes grapple skidders and identifies the major components and parts most commonly associated therewith. Illustrations used herein are not intended to include all existing commercial machines or to be exactly descriptive of any particular machine. They have been included to facilitate application of this document.
HISTORICAL
2007-08-22
Standard
J1254_200708
This SAE Standard includes names of major components and parts peculiar to this type of machine. Illustrations used here are not intended to include all existing commercial machines or be exactly descriptive of any particular machine. They have been provided to describe the principles to be used in applying this document.
CURRENT
2004-06-28
Standard
J1209_200406
This SAE standard describes a procedure and the terminology for identifying and classifying mobile forestry machines which may be portable or self-propelled. Identification is determined by endpoint usage as intended by the manufacturer's design objectives. This document applies to machines that are designed for use in site preparation, planting, transporting, and processing wood and wood fiber. Specifically excluded are machines used exclusively in sawmills or wood yards, on-highway transport vehicles, and aerial vehicles.
CURRENT
2003-11-03
Standard
J1112_200310
This SAE Standard establishes definitions of specifications most commonly associated with grapple skidders. Specifications common to all articulated, rubber-tired log skidders are included in SAE J1110. The dimensions included in this document are basic and may be supplemented by the individual machine manufacturer. Dimensions shall be stated in SI units. Illustrations used herein are not intended to include all existing commercial machines or to be exactly descriptive of any particular machine. They have been included to facilitate application of this document.
CURRENT
2002-09-20
Standard
J2711_200209
This SAE Recommended Practice was established to provide an accurate, uniform and reproducible procedure for simulating use of heavy-duty hybrid-electric vehicles (HEVs) and conventional vehicles on dynamometers for the purpose of measuring emissions and fuel economy. Although the recommended practice can be applied using any driving cycle, the practice recommends three cycles: the Manhattan cycle, representing low-speed transit bus operation; the Orange County Transit Cycle, representing intermediate-speed bus operation; and the Urban Dynamometer Driving Schedule (UDDS) cycle representing high-speed operation for buses and tractor-trailers. This document does not specify which emissions constituents to measure (e.g., HC, CO, NOx, PM, CO2), as that decision will depend on the objectives of the tester.
HISTORICAL
2002-06-07
Standard
J2233_200206
This SAE Recommended Practice, limited to liquid coolant systems, establishes uniform cold weather bus vehicle heating system test procedures for all vehicles designed to transport 10 or more passengers. Required test equipment, facilities, and definitions are included. Defrosting and defogging procedures and requirements are established by SAE J381 which is hereby included by reference. This procedure is designed to provide bus manufacturers with a cost-effective, standardized test method to provide relative approximations of cold weather interior temperatures.
HISTORICAL
2002-03-20
Standard
J2358_200203
This SAE Standard defines the safety and performance requirements for Low Speed Vehicles ("LSV"). The safety specifications in this document apply to any powered vehicle with a minimum of 4-wheels, a maximum level ground speed of more than 32 km/h (20 mph) but less than 40 km/h (25 mph), a maximum rated capacity of 500 kg (1100 lb), and a maximum gross vehicle weight of 1135 Kg (2500 lb), that is intended for transporting not more than four (4) persons and operating on designated roadways where permitted by law. Personal Neighborhood Vehicles (PNVs) have the same general specifications as LSVs, but the maximum level ground speed is limited to 32 km/h (20 mph).
Viewing 1 to 30 of 50

Filter

  • Standard
    50