Criteria

Text:
Topic:
Sector:
Content:
Display:

Results

Viewing 1 to 30 of 305
CURRENT
2017-02-21
Standard
J2773_201702
This Standard describes methods to understand the risks associated with vehicle mobile air conditioning [MAC] systems in all aspects of a vehicle’s lifecycle including design, production, assembly, operation and end of life. Information for input to the risk assessment is provided in the Appendices of this document. This information should not be considered to be complete, but only a reference of some of the data needed for a complete analysis of the risk associated with the use of refrigerants in MAC systems.
CURRENT
2017-02-16
Standard
J1979_201702
SAE J1979/ISO 15031-5 set includes the communication between the vehicle’s OBD systems and test equipment implemented across vehicles within the scope of the legislated emissions-related OBD. To achieve this, it is based on the Open Systems Interconnection (OSI) Basic Reference Model in accordance with ISO/IEC 7498-1 and ISO/IEC 10731, which structures communication systems into seven layers.
2017-01-05
WIP Standard
AIR7521
This document summarizes a number of guidance values and measured values in published literature for Substances listed in ARP4418.
2016-11-18
WIP Standard
J100
This SAE Recommended Practice establishes boundaries for shade bands on glazed surfaces in class "A" vehicles. These boundaries are located so that the shade band can provide occupant comfort and driver vision protection from glare, with respect to solar radiation, under some lighting and driving conditions. Since shade bands transmit less visible light than adjacent glazed surfaces, the shade band boundaries establish boundaries for the driver's field of view.
CURRENT
2016-11-15
Standard
J100_201611
This SAE Recommended Practice establishes boundaries for shade bands on glazed surfaces in class "A" vehicles. These boundaries are located so that the shade band can provide occupant comfort and driver vision protection from glare, with respect to solar radiation, under some lighting and driving conditions. Since shade bands transmit less visible light than adjacent glazed surfaces, the shade band boundaries establish boundaries for the driver's field of view.
CURRENT
2016-09-16
Standard
J1752/2_201609
This SAE Recommended Practice defines a method for evaluating the near field electric or magnetic component of the electromagnetic field at the surface of an integrated circuit (IC). This technique is capable of providing a detailed pattern of the RF sources internal to the IC. The resolution of the pattern is determined by the characteristics of the probes used and the precision of the mechanical probe positioner. The method is usable over the 10 MHz to 3 GHz frequency range with existing probe technology. The probe is mechanically scanned according to a programmed pattern in a plane parallel or perpendicular to the IC surface and the data is computer processed to provide a color-enhanced representation of field strength at the scan frequency. This procedure is applicable to measurements from an IC mounted on any circuit board that is accessible to the scan probe. For comparisons, the standardized test board shall be used.
CURRENT
2016-08-23
Standard
J2914_201608
This document provides an overview on how and why EGR coolers are utilized, defines commonly used nomenclature, discusses design issues and trade-offs, and identifies common failure modes. The reintroduction of exhaust gas into the combustion chamber is just one component of the emission control strategy for internal combustion (IC) engines, both diesel and gasoline, and is useful in reducing exhaust port emission of Nitrogen Oxides (NOx). Other means of reducing NOx exhaust port emissions are briefly mentioned, but beyond the scope of this document.
CURRENT
2016-04-05
Standard
J3071_201604
This SAE Battery Identification and Cross Contamination Prevention document is intended to provide information that may be applicable to all types of Rechargeable Energy Storage System (RESS) devices. It is important to develop a system that can facilitate sorting by chemistry. The recycler is interested in the chemistry of the RESS. This is true for the recyclers of Lead Acid, Lithium Ion, Nickel Cadmium etc. Thus recyclers of RESS will receive RESS from automotive, commercial, and industrial applications. These RESS have the potential to be contaminated with a RESS of an incompatible chemistry. It is recognized that mitigation methods to reduce or eliminate the introduction of incompatible chemistries into a given recycling stream would also benefit safety and the environment.
2016-03-31
WIP Standard
J2974
This SAE Technical Information Report provides information on Automotive Battery Recycling. This document provides a compilation of current recycling definitions, technologies and flow sheets and their application to different battery chemistries.
CURRENT
2016-03-03
Standard
J2683_201603
This SAE Standard applies to Carbon Dioxide R-744 refrigerant used to service motor vehicle passenger air-conditioning (A/C) systems designed to use CO2 (R-744). Hermetically sealed, refrigerated cargo systems are not covered by this document.
CURRENT
2015-11-05
Standard
J1939/3_201511
SAE J1939-03 provides requirements and guidelines for the implementation of On Board Diagnostics (OBD) on heavy-duty vehicles (HDV) using the SAE J1939 family of standards. The guidelines identify where the necessary information to meet OBD regulations may be found among the SAE J1939 document set. Key requirements are identified here to insure the interoperability of OBD scan tools across individual OBD compliant vehicles. Market-defined regulations permit the use of SAE J1939 to meet OBD requirements. Implementers are cautioned to obtain and review the specific regulations for the markets where their products are sold. This document is focused on guidelines and requirements to satisfy the State of California Air Resources Board (ARB), the authors of 13 CCR 1971.1, United States Environmental Protection Agency, Euro IV and V requirements from European Commission directives, and UN/ECE WP 29 GRPE WWH OBD Global Technical Regulation (GTR).
CURRENT
2015-07-08
Standard
J3030_201507
The purpose of this SAE Standard is to establish the specific minimum equipment requirements for recovery/recycling/recharge equipment intended for use with both R-1234yf and R-134a in a common refrigerant circuit that has been directly removed from, and is intended for reuse in, mobile air-conditioning (A/C) systems. This document does not apply to equipment used for R-1234yf and R-134a having a common enclosure with separate circuits for each refrigerant, although some amount of separate circuitry for each refrigerant could be used.
CURRENT
2015-04-23
Standard
J2992_201504
The scope of this document focuses on the tests required by EPA to validate the performance of the FTIR system following the section in the Code of Federal Regulations Part 1065 (40CFR1U.1065 and hereafter referred to as “EPA Part 1065”) on the guidelines and performance criteria for various regulated gases. This document focuses on the use of continuous emissions sampling for both Engine and Vehicle testing. Future addenda will be needed to cover bag and other sampling techniques. Gas components that do not currently have performance criteria but may soon be regulated are noted and EPA suggestions as to what should be required are applied. This will help ensure that the FTIR will be recognized as a valid and alternative tool for engine exhaust emissions testing. Components in engine exhaust that are specifically called out in this document include: carbon monoxide (CO), carbon dioxide (CO2), oxides of nitrogen (NO, NO2 and N2O), ammonia (NH3), methane (CH4), and formaldehyde (H2CO).
2015-04-19
WIP Standard
J1115
Historically SAE has been concerned with nomenclature as an integral part of the standards development process. Guidelines for automotive nomenclature were written in 1916, were last revised in 1941, and were included in the SAE Handbook until 1962. The present diversity of groups working on nomenclature in the various ground vehicle committees led to the organization of the Nomenclature Advisory Committee under SAE Automotive Council.
2015-04-19
WIP Standard
J2740
This Technical Information Report defines the General Motors UART Serial Data Communications Bus, commonly referred to as GM UART. This document should be used in conjunction with SAE J2534-2 in order to fully implement GM UART in an SAE J2534 interface. SAE J2534-1 includes requirements for an interface that can be used to program certain emission-related Electronic Control Units (ECU) as required by U.S. regulations, and SAE J2534-2 defines enhanced functionality required to program additional ECUs not mandated by current U.S. regulations. The purpose of this document is to specify the requirements necessary to implement GM UART in an aftermarket SAE J2534 interface intended for use by independent automotive service facilities to program GM UART ECUs in General Motors vehicles.
CURRENT
2015-04-15
Standard
J2974_201504
This SAE Technical Information Report provides information on Automotive Battery Recycling. This document provides a compilation of current recycling definitions, technologies and flow sheets and their application to different battery chemistries.
2015-04-09
WIP Standard
J3094
Create a standard for measurement of the performance characteristics of an Internal Heat Exchanger. The standard should make it easier to innovate designs and bring improvements to this new technology.
CURRENT
2015-01-23
Standard
J551/1_201501
This SAE Standard covers the measurement of radio frequency radiated emissions and immunity. Each part details the requirements for a specific type of electromagnetic compatibility (EMC) test and the applicable frequency range of the test method. The methods are applicable to a vehicle, boat, machine or device powered by an internal combustion engine or battery powered electric motor. Operation of all engines or motors (main and auxiliary) of a vehicle, boat, machine or device is included. All equipment normally operating when the vehicle, boat, machine or device is in operation is included. Operator controlled equipment is included or excluded as specified in the individual document parts. As a special case, CISPR 12 applies to battery powered floor finishing equipment, but robot carpet sweepers are excluded. By reference, IEC CISPR 12 and CISPR 25 are adopted as the standards for the measurement of vehicle emissions.
CURRENT
2015-01-15
Standard
J2610_201501
The purpose of this SAE Information Report is to specify the requirements necessary to fully define the Serial Data Communication Interface (SCI) used in the reprogramming of emission-related powertrain Electronic Control Units (ECU) in Fiat Chrysler Automobiles (FCA) vehicles. It is intended to satisfy new regulations proposed by the federal U.S. Environmental Protection Agency (EPA) and California Air Resource Board (CARB) regulatory agencies regarding “pass-thru programming” of all On-Board Diagnostic (OBD) compliant emission-related powertrain devices. These requirements are necessary to provide independent automotive service organizations and after-market scan tool suppliers the ability to reprogram emission-related powertrain ECUs for all manufacturers of automotive vehicles. Specifically, this document details the SCI physical layer and SCI data link layer requirements necessary to establish communications between a diagnostic tester and an ECU.
CURRENT
2014-08-13
Standard
J184_201408
Various SAE vehicle sound level measurement procedures require use of a sound level meter which meets the Type 1 or Type 2 requirements of ANSI S1.4-1983 (see 2.1.1.1), or an alternative system which can be proved to provide equivalent test data. The purpose of this SAE Recommended Practice is to provide a procedure for determining if a sound data acquisition system (SDAS) has electro-acoustical performance equivalent to such a meter. By assuring equivalent performance of the test instrumentation, the equivalence of test data is assured. Two general configurations of sound data acquisition systems will be encompassed (see Figure 1). The first configuration consists of instrument sections which perform as a sound level meter. The second configuration is a system which records data for later processing. The intent of this document is to establish guidelines which permit the test engineer to insure equivalence of sound data acquisition systems to a sound level meter.
HISTORICAL
2014-08-11
Standard
J1979_201408
This document supersedes SAE J1979 May 2007, and is technically equivalent to ISO 15031-5 2010, with the addition of new capabilities required by revised regulations from the California Air Resources Board and revised regulations from the European Commission. This document is intended to satisfy the data reporting requirements of On-Board Diagnostic (OBD) regulations in the United States and Europe, and any other region that may adopt similar requirements in the future.
CURRENT
2014-06-16
Standard
J1892_201406
This SAE Recommended Practice describes the basic content requirements, bar-code specifications, and functional test specifications of a vehicle emission configuration (VEC) label. On the vehicle, the VEC label is to be mounted under the hood in a readily accessible location for use of a bar-code scanning device. This document specifies a permanent vehicle emission configuration label that can be automatically identified through a bar-coded format.
2014-06-09
WIP Standard
ARP6331
This document recommends contents for Emergency Medical Kits, including medications and instrumentation, intended for use on passenger-carrying aircraft serviced by at least 1 flight attendant. Recommended practices for carriage of, access to, and maintenance of Emergency Medical Kits are also included.
CURRENT
2014-06-04
Standard
J2880_201406
These Protocols can be used for all forms of motorsports; however, only certain combinations of Green Racing Elements will result in motorsport competitions that are recognized as Green Racing events. As new information, fuels and technologies emerge, addendums or new protocols will be developed. The SAE International (SAE) Motorsports Engineering Activity is also an invaluable source of reference materials and ongoing technical advice providing access to the constantly evolving set of best safety and operational practices for current and emerging technologies. This is especially true with regard to high voltage safety and the adoption of other advanced propulsion and fuel system technologies.
CURRENT
2014-05-16
Standard
J1207_201405
This SAE Recommended Practice sets forth the instrumentation, environment, and test procedures to be used in measuring the silencer system effectiveness in reducing intake or exhaust sound level of internal combustion engines. The system shall include the intake or exhaust silencer, related piping, and components. This procedure is intended for engine-dynamometer testing and is not necessarily applicable to vehicle testing (see Appendix A). The effect of the exhaust or intake system on the sound level of the overall machine must be determined using other procedures. This procedure may be successively applied to various silencer configurations to determine relative effectiveness for that engine. Insertion loss for individual silencers may be calculated through measurement of the silenced and unsilenced system.
CURRENT
2014-05-16
Standard
J1074_201405
This SAE Recommended Practice sets forth the equipment, environment, and test procedures to be used in measuring sound levels of engines. The purpose is to provide a uniform method of measuring the maximum acoustical radiation from the exterior surfaces of an engine under representative engine operating conditions. The measured sound levels will be useful in development of engines, comparison of engines, and installation of engines in various applications. The correlation of the measured engine sound levels to the various application sound levels will have to be developed.
CURRENT
2014-05-16
Standard
J57_201405
This procedure provides for the measurement of the sound generated by a test tire, mounted on a single-axle trailer, operated at multiple speeds.
CURRENT
2014-05-16
Standard
J1060_201405
This SAE Recommended Practice establishes a rating scale for subjective evaluations of noise and discomfort in motor vehicles. Through test procedures utilizing specific vehicles on specific roads, the scale may be utilized to assess the relative contributions of tires to noise and discomfort. The noise and ride comfort characteristics attributed to automotive tires have traditionally been estimated by subjectively assigning number designations (commonly on a 1 to 10 scale) to the audible and tactile sensations observed while traversing a given road course in a vehicle equipped with the tires under evaluation. Regardless of advances in objective measurements of tire properties related to noise and discomfort, subjective evaluation will continue to be necessary for the purpose of establishing the significance of such measurements.
CURRENT
2014-02-21
Standard
J2191_201402
This SAE document defines a recommended practice for implementing circuit identification for electrical power and signal distribution systems of the Class 8 trucks and tractors. This document provides a description of a supplemental circuit identifier that shall be utilized in conjunction with the original equipment manufacturer’s primary circuit identification as used in wire harnesses but does not include electrical or electronic devices which have pigtails. The supplemental circuit identifier is cross-referenced to a specified subsystem of the power and signal distribution system identified in Section 5.
2014-01-09
WIP Standard
J2772
This Standard is restricted to refrigeration circuits that provide air-conditioning for the passenger compartments of passenger and commercial vehicles. This Standard includes analytical and physical test procedures to evaluate concentration inside the passenger compartment. In the early phases of vehicle evaluation, usage of the analytical approach may be sufficient without performing physical tests. The physical test procedure involves releasing refrigerant from an external source to a location adjacent to the evaporator core (inside the HVAC-Module). An apparatus is used to provide a repeatable, calibrated leak rate. If the system has multiple evaporators, leakage could be simulated at any of the evaporator locations. This standard gives detail information on the techniques for measuring R-744 [CO2] and R-1234yf [HFO-1234yf], but the general techniques described here can be used for other refrigerants as well.
Viewing 1 to 30 of 305

Filter