Criteria

Text:
Topic:
Content:
Display:

Results

Viewing 31 to 60 of 711
CURRENT
2016-03-03
Standard
J2683_201603
This SAE Standard applies to Carbon Dioxide R-744 refrigerant used to service motor vehicle passenger air-conditioning (A/C) systems designed to use CO2 (R-744). Hermetically sealed, refrigerated cargo systems are not covered by this document.
2016-02-29
WIP Standard
AIR6418
The scope of this document will consider a broader range of contaminants than ARP4418. In addition, it may provide guidance for measuring on wing, as well as in test cells, Finally, it may also discuss transient measurements, as well as steady state measurements.
CURRENT
2015-12-02
Standard
AMS3092A
This specification establishes requirements for solvent-based and water-based release agents, in bulk or aerosol form.
CURRENT
2015-11-05
Standard
J1939/3_201511
SAE J1939-03 provides requirements and guidelines for the implementation of On Board Diagnostics (OBD) on heavy-duty vehicles (HDV) using the SAE J1939 family of standards. The guidelines identify where the necessary information to meet OBD regulations may be found among the SAE J1939 document set. Key requirements are identified here to insure the interoperability of OBD scan tools across individual OBD compliant vehicles. Market-defined regulations permit the use of SAE J1939 to meet OBD requirements. Implementers are cautioned to obtain and review the specific regulations for the markets where their products are sold. This document is focused on guidelines and requirements to satisfy the State of California Air Resources Board (ARB), the authors of 13 CCR 1971.1, United States Environmental Protection Agency, Euro IV and V requirements from European Commission directives, and UN/ECE WP 29 GRPE WWH OBD Global Technical Regulation (GTR).
CURRENT
2015-10-08
Standard
J3078/6_201510
SAE J3078/6 specifies a test method for simulating solar heating in the laboratory and measuring the radiant heat energy from a natural or simulated source. It is applicable to Off-Road Self-Propelled Work Machines as defined in SAE J1116 and Agricultural Tractors as defined in ANSI/ASAE S390.
CURRENT
2015-09-07
Standard
ARP5533A
This SAE Aerospace Recommended Practice (ARP) covers the requirements for a Stationary Runway Weather Information System (referred to as the system) to monitor the surface conditions of airfield operational areas to ensure safer ground operations of aircraft. The system provides (1) temperature and condition information of runway, taxiway, and ramp pavements and (2) atmospheric weather conditions that assist airport personnel to maintain safer and more efficient airport operations. The system can be either a wired system or a wireless system.
CURRENT
2015-07-28
Standard
AS8055A
This SAE Aerospace Standard (AS) specifies minimum performance standards for airborne binocular Head-Up Displays (HUDs) in fixed wing (14 CFR part 23, 25) aircraft; while this document is also applicable to rotorcraft (14 CFR part 27, 29) additional performance standards may be required for rotorcraft. This aerospace standard covers basic display standards, but does not include specific application requirements. Specific applications can include flight instrumentation, navigation, engine and system status, alerting, surveillance, communication, terrain awareness, weather, enhanced vision, synthetic vision and other displays. This document covers criteria for conformal and non-conformal HUD systems that are intended for use in the flight deck by the pilot or copilot. Display minimum performance characteristics are specified for standard and other environmental conditions for the purpose of product qualification.
CURRENT
2015-07-08
Standard
J3030_201507
The purpose of this SAE Standard is to establish the specific minimum equipment requirements for recovery/recycling/recharge equipment intended for use with both R-1234yf and R-134a in a common refrigerant circuit that has been directly removed from, and is intended for reuse in, mobile air-conditioning (A/C) systems. This document does not apply to equipment used for R-1234yf and R-134a having a common enclosure with separate circuits for each refrigerant, although some amount of separate circuitry for each refrigerant could be used.
CURRENT
2015-05-26
Standard
AMS2641C
This specification covers two types of refined hydrocarbon compounds in the form of liquids.
CURRENT
2015-04-23
Standard
J2992_201504
The scope of this document focuses on the tests required by EPA to validate the performance of the FTIR system following the section in the Code of Federal Regulations Part 1065 (40CFR1U.1065 and hereafter referred to as “EPA Part 1065”) on the guidelines and performance criteria for various regulated gases. This document focuses on the use of continuous emissions sampling for both Engine and Vehicle testing. Future addenda will be needed to cover bag and other sampling techniques. Gas components that do not currently have performance criteria but may soon be regulated are noted and EPA suggestions as to what should be required are applied. This will help ensure that the FTIR will be recognized as a valid and alternative tool for engine exhaust emissions testing. Components in engine exhaust that are specifically called out in this document include: carbon monoxide (CO), carbon dioxide (CO2), oxides of nitrogen (NO, NO2 and N2O), ammonia (NH3), methane (CH4), and formaldehyde (H2CO).
2015-04-19
WIP Standard
J1115
Historically SAE has been concerned with nomenclature as an integral part of the standards development process. Guidelines for automotive nomenclature were written in 1916, were last revised in 1941, and were included in the SAE Handbook until 1962. The present diversity of groups working on nomenclature in the various ground vehicle committees led to the organization of the Nomenclature Advisory Committee under SAE Automotive Council.
2015-04-19
WIP Standard
J2740
This Technical Information Report defines the General Motors UART Serial Data Communications Bus, commonly referred to as GM UART. This document should be used in conjunction with SAE J2534-2 in order to fully implement GM UART in an SAE J2534 interface. SAE J2534-1 includes requirements for an interface that can be used to program certain emission-related Electronic Control Units (ECU) as required by U.S. regulations, and SAE J2534-2 defines enhanced functionality required to program additional ECUs not mandated by current U.S. regulations. The purpose of this document is to specify the requirements necessary to implement GM UART in an aftermarket SAE J2534 interface intended for use by independent automotive service facilities to program GM UART ECUs in General Motors vehicles.
CURRENT
2015-04-15
Standard
J2974_201504
This SAE Technical Information Report provides information on Automotive Battery Recycling. This document provides a compilation of current recycling definitions, technologies and flow sheets and their application to different battery chemistries.
2015-04-09
WIP Standard
J3094
Create a standard for measurement of the performance characteristics of an Internal Heat Exchanger. The standard should make it easier to innovate designs and bring improvements to this new technology.
2015-02-13
WIP Standard
ARP4955B
The purpose of this SAE Aerospace Recommended Practice (ARP) is to establish guidelines for the measurement of static and dynamic characteristic properties of aircraft tires. It is intended as a general guide toward standard practice, but may be subject to frequent changes to keep pace with experience and technical advances.
2015-02-11
WIP Standard
ARP1256E
This Aerospace Recommended Practice (ARP) describes the continuous sampling and analysis of gaseous emissions from aircraft gas turbine engines. The measured gas species include carbon monoxide (CO), carbon dioxide (CO₂), nitric oxide (NO), nitrogen dioxide (NO₂), total hydrocarbons (CHα where"α" is the hydrogen to carbon ratio of the fuel) and water vapor (H₂O). This ARP excludes engine operating procedures and test modes, and is not intended for in-flight testing, nor does it apply to engines operating in the afterburning mode. It is recognized that there will probably be major advances in the gas analysis measurement technology. It is not the intent of this ARP to exclude other analysis techniques, but to form the basis of the minimum amount of conventional instruments (those in common industry usage over the last fifteen years) required for the analysis of aircraft engine exhaust.
2015-01-26
WIP Standard
ARP6320
This Aerospace Recommended Practice (ARP) consists of methodologies for the measurement of non-volatile particulate matter (nvPM) emissions at the exit plane of aircraft gas turbine engines. The methods describe means of sampling and measuring particle mass concentration, particle number concentration and reporting of emissions indices through the use of an appropriate sampling system and instrumentation that goes beyond the measurements of visible obscuration as described in ARP 1179 for Smoke Number (SN).
CURRENT
2015-01-23
Standard
J551/1_201501
This SAE Standard covers the measurement of radio frequency radiated emissions and immunity. Each part details the requirements for a specific type of electromagnetic compatibility (EMC) test and the applicable frequency range of the test method. The methods are applicable to a vehicle, boat, machine or device powered by an internal combustion engine or battery powered electric motor. Operation of all engines or motors (main and auxiliary) of a vehicle, boat, machine or device is included. All equipment normally operating when the vehicle, boat, machine or device is in operation is included. Operator controlled equipment is included or excluded as specified in the individual document parts. As a special case, CISPR 12 applies to battery powered floor finishing equipment, but robot carpet sweepers are excluded. By reference, IEC CISPR 12 and CISPR 25 are adopted as the standards for the measurement of vehicle emissions.
CURRENT
2015-01-15
Standard
J2610_201501
The purpose of this SAE Information Report is to specify the requirements necessary to fully define the Serial Data Communication Interface (SCI) used in the reprogramming of emission-related powertrain Electronic Control Units (ECU) in Fiat Chrysler Automobiles (FCA) vehicles. It is intended to satisfy new regulations proposed by the federal U.S. Environmental Protection Agency (EPA) and California Air Resource Board (CARB) regulatory agencies regarding “pass-thru programming” of all On-Board Diagnostic (OBD) compliant emission-related powertrain devices. These requirements are necessary to provide independent automotive service organizations and after-market scan tool suppliers the ability to reprogram emission-related powertrain ECUs for all manufacturers of automotive vehicles. Specifically, this document details the SCI physical layer and SCI data link layer requirements necessary to establish communications between a diagnostic tester and an ECU.
CURRENT
2015-01-12
Standard
ARP5740
This SAE Aerospace Recommended Practice (ARP) addresses the information content for the electronic presentation of data linked weather Meteorological (MET) information used in the cockpit. It defines guidelines for the electronic presentation of MET information (including text, graphics, textures, icons, and symbology) to the flight crew. This ARP is applicable to certified equipment for the electronic display (whether installed or portable) of MET information in the cockpit. This ARP also provides a set of symbols that illustrate the depiction of data linked MET information on flight deck display systems such as Navigation Displays, Multi-function Displays, and Electronic Flight Bags. These recommendations complement standard symbology guidelines for airborne applications already in existence (see reference section for applicable documents).
CURRENT
2014-11-25
Standard
AS245C
This specification covers the following types and classes of extinguishers: Type I Stored pressure type Category A - Operational Temperature range −40 to +140 °F (−40 to +60 °C) Category B - Operational Temperature range +35 to +140 °F (+1.7 to +60 °C) Type II Cartridge operated type Category A - Operational Temperature range −40 to +140 °F (−40 to +60 °C) Category B - Operational Temperature range +35 to +140 °F (+1.7 to +60 °C)
CURRENT
2014-11-24
Standard
J2698_201411
This SAE Recommended Practice covers the design and application of primary on-board wiring distribution system harnessing for surface vehicles. This document is intended for single phase nominal 120 VAC circuits that provide power to truck sleeper cab hotel loads so that they may operate with the main propulsion engine turned off. The power supply comes from alternative sources such as land-based grid power, DC-AC inverters and auxiliary power generators. The circuits may also provide power to improve vehicle performance through charging batteries or operating cold-weather starting aids.
CURRENT
2014-08-13
Standard
J184_201408
Various SAE vehicle sound level measurement procedures require use of a sound level meter which meets the Type 1 or Type 2 requirements of ANSI S1.4-1983 (see 2.1.1.1), or an alternative system which can be proved to provide equivalent test data. The purpose of this SAE Recommended Practice is to provide a procedure for determining if a sound data acquisition system (SDAS) has electro-acoustical performance equivalent to such a meter. By assuring equivalent performance of the test instrumentation, the equivalence of test data is assured. Two general configurations of sound data acquisition systems will be encompassed (see Figure 1). The first configuration consists of instrument sections which perform as a sound level meter. The second configuration is a system which records data for later processing. The intent of this document is to establish guidelines which permit the test engineer to insure equivalence of sound data acquisition systems to a sound level meter.
HISTORICAL
2014-08-11
Standard
J1979_201408
This document supersedes SAE J1979 May 2007, and is technically equivalent to ISO 15031-5 2010, with the addition of new capabilities required by revised regulations from the California Air Resources Board and revised regulations from the European Commission. This document is intended to satisfy the data reporting requirements of On-Board Diagnostic (OBD) regulations in the United States and Europe, and any other region that may adopt similar requirements in the future.
CURRENT
2014-08-05
Standard
ARP5149BDA
This Digital Annex (DA) contains the current, full-PDF version of ARP5149B, Training Program Guidelines for Deicing/Anti-Icing of Aircraft on Ground, as well as .jpeg format files of Appendix D, Application Guidelines Configuration, Critical Component, and Spray Area Diagrams for Aircraft. The .jpeg diagram files may be used by purchasers in accordance with the terms of the included license agreement.
CURRENT
2014-07-22
Standard
AS9968
This AS describes a standard method for viscosity measurements of thickened (AMS1428) anti-icing fluids. Fluid manufacturers may publish alternate methods for their fluids. In case of conflicting results between the two methods, the manufacturer method takes precedence. To compare viscosities, exactly the same measurement elements (including spindle and container size) must have been used to obtain those viscosities.
2014-07-22
WIP Standard
AS6332
A program, which ensures quality with the relevant standards shall be introduced for all on-line Stations where de-icing/anti-icing of aircraft on the ground is either normally carried out, or where local conditions may periodically lead to a requirement for airplcraft to be de-iced/anti-iced. Deficiencies, in regard to a Station's local de-icing/anti-icing procedures, shall be identified and subsequently actioned through this program, thereby ensuring that the required safety standards are maintained.
2014-07-08
WIP Standard
AIR6504
This SAE Aerospace Information Report (AIR) provides a method for assessing particle losses that occur in a sampling system of specified geometry based on the nvPM mass and number measured at the end of the sampling system. Both size dependent diffusion loss and size independent thermophoretic loss mechanisms are included in the method. The penetration function of that system must be determined by measurement and/or by computation using an analytical method as described within this report. The outcome of this line loss assessment provides estimated correction factors for nvPM mass and number concentration with associated uncertainties based upon nvPM measurement uncertainties and method assumptions. These correction factors give an estimation of nvPM mass and number values at the inlet to the sampling system.
CURRENT
2014-06-24
Standard
AS5901C
This document establishes the minimum requirements for an environmental test chamber, and test procedures to carry out anti-icing performance tests according to the current materials specification for aircraft deicing/anti-icing fluids. The primary purpose for such a test method is to determine the anti-icing endurance under controlled laboratory conditions of AMS1424 Type I and AMS1428 Type II, III, and IV fluids.
Viewing 31 to 60 of 711