Criteria

Text:
Topic:
Content:
Display:

Results

Viewing 1 to 30 of 372
2017-10-18
WIP Standard
J3160
The standard will provide guidance on best practices to ensure consistent, high quality measurements of Particle Number from both raw and dilute vehicle and engine exhaust streams. Key elements will include proper positioning of sample probes, conditioning of sample streams and maintenance.
CURRENT
2017-10-10
Standard
AIR6504
This SAE Aerospace Information Report (AIR) provides a method for assessing particle losses that occur in a sampling system of specified geometry based on the nvPM mass and number measured at the end of the sampling system. Both size dependent diffusion loss and size independent thermophoretic loss mechanisms are included in the method. The penetration function of that system must be determined by measurement and/or by computation using an analytical method as described within this report. The outcome of this line loss assessment provides estimated correction factors for nvPM mass and number concentration with associated uncertainties based upon nvPM measurement uncertainties and method assumptions. These correction factors give an estimation of nvPM mass and number values at the inlet to the sampling system.
2017-07-28
WIP Standard
ARP8000
This SAE Aerospace Recommended Practice (ARP) document covers the requirements for a Snowcompressor with carrier vehicle used to clear snow from airport operational areas by compressing the volume of collected snow into smaller volumes for loading into a hauling/dump truck or for depositing reduced-volume windrows for snow banking. The term carrier vehicle represents the various self-propelled prime movers that provide the power necessary to move snow and ice control equipment during winter operations. For two-stage rotary plows that primarily are used to cast heavy concentrations of snow away from airport operational areas such as runways and taxiways, see ARP5539.
CURRENT
2017-07-14
Standard
AIR5479B
This SAE Aerospace Information Report (AIR) describes the performance of plating’s and coatings for landing gear that potentially provide environmental compliance benefits versus the current baseline processes. The hazardous systems addressed in this version of the document include cadmium plating, chromated primers, and high VOC (volatile organic compounds) topcoats. The AIR applies to landing gear structures and mechanisms for all types of civil and military aircraft. The potential replacements apply to both Original Equipment Manufacturer (OEM) hardware and overhaul of in-service landing gears.
2017-06-26
WIP Standard
ARP6481
This SAE Aerospace Recommended Practice (ARP) describes a method for assessing size dependent particle losses in a sampling and measurement system of specified geometry utilizing on the non-volatile PM (nvPM) mass and number concentrations measured at the end of the sampling system. The penetration functions of the sampling and measurement system may be determined either by measurement or by analytic computational methods. Loss mechanisms including thermophoretic (which has a very weak size dependence) and size dependent losses are considered in this method along with the uncertainties due to both measurement error and the assumptions of the method. The results of this system loss assessment allow development of estimated correction factors for nvPM mass and number concentrations to account for the system losses facilitating estimation of the nvPM mass and number at the engine exhaust nozzle exit plane.
2017-06-12
WIP Standard
ARP6954
This SAE Aerospace Resource Document (ARD) document covers the requirements for a self-propelled GRV, intended for use at airports to collect spent aircraft de-icing fluid (ADF) from the surface of de-icing areas. This unit will recover de-icing fluid from the surface, which will be stored in a containment unit on the vehicle. The GRV must be capable of night and day operations in all weather conditions, as required.
2017-05-18
WIP Standard
J1979
SAE J1979/ISO 15031-5 set includes the communication between the vehicle's OBD systems and test equipment implemented across vehicles within the scope of the legislated emissions-related OBD.
CURRENT
2017-02-16
Standard
J1979_201702
SAE J1979/ISO 15031-5 set includes the communication between the vehicle’s OBD systems and test equipment implemented across vehicles within the scope of the legislated emissions-related OBD. To achieve this, it is based on the Open Systems Interconnection (OSI) Basic Reference Model in accordance with ISO/IEC 7498-1 and ISO/IEC 10731, which structures communication systems into seven layers.
2017-01-05
WIP Standard
AIR7521
This document summarizes a number of guidance values and measured values in published literature for Substances listed in ARP4418.
CURRENT
2016-12-13
Standard
AIR6212
This document collates the ways and means that existing sensors can identify the platform’s exposure to volcanic ash. The capabilities include real-time detection and estimation, and post flight determinations of exposure and intensity. The document includes results of initiatives with the Federal Aviation Administration (FAA), the European Aviation Safety Agency (EASA), the International Civil Aviation Organization (ICAO), Transport Canada, various research organizations, Industry and other subject matter experts. The document illustrates the ways that an aircraft can use existing sensors to act as health monitoring tools so as to assess the operational and maintenance effects related to volcanic ash incidents and possibly help determine what remedial action to take after encountering a volcanic ash (VA) event.
CURRENT
2016-09-16
Standard
J1752/2_201609
This SAE Recommended Practice defines a method for evaluating the near field electric or magnetic component of the electromagnetic field at the surface of an integrated circuit (IC). This technique is capable of providing a detailed pattern of the RF sources internal to the IC. The resolution of the pattern is determined by the characteristics of the probes used and the precision of the mechanical probe positioner. The method is usable over the 10 MHz to 3 GHz frequency range with existing probe technology. The probe is mechanically scanned according to a programmed pattern in a plane parallel or perpendicular to the IC surface and the data is computer processed to provide a color-enhanced representation of field strength at the scan frequency. This procedure is applicable to measurements from an IC mounted on any circuit board that is accessible to the scan probe. For comparisons, the standardized test board shall be used.
CURRENT
2016-08-23
Standard
J2914_201608
This document provides an overview on how and why EGR coolers are utilized, defines commonly used nomenclature, discusses design issues and trade-offs, and identifies common failure modes. The reintroduction of exhaust gas into the combustion chamber is just one component of the emission control strategy for internal combustion (IC) engines, both diesel and gasoline, and is useful in reducing exhaust port emission of Nitrogen Oxides (NOx). Other means of reducing NOx exhaust port emissions are briefly mentioned, but beyond the scope of this document.
CURRENT
2016-06-09
Standard
ARP598D
This SAE Aerospace Recommended Practice (ARP) defines the materials, apparatus and procedure for sizing and counting of particulate contamination, 5 μm or greater, in hydraulic fluid samples by membrane filtration iwth microscopic counting. It is capable of counting particulate matter in samples withdrawn from fluid power systems as identified by the 12 classes of SAE AS 4059 or NAS 1638 and projected beyond these for the five standard ranges specified and can thus serve as the primary document to determine acceptability. It is also capable of revealing but not measuring evidence of abnormal amount of water, other fluids, fine particulate and other materials, especially fibers and metals. It is applicable to all military, civil, space vehicles and test equipment.
CURRENT
2016-04-13
Standard
ARP1533C
SAE Aerospace Recommended Practice ARP1533 is a procedure for the analysis and evaluation of the measured composition of the exhaust gas from aircraft engines. Measurements of carbon monoxide, carbon dioxide, total hydrocarbon, and the oxides of nitrogen are used to deduce emission indices, fuel-air ratio, combustion efficiency, and exhaust gas thermodynamic properties. The emission indices (EI) are the parameters of critical interest to the engine developers and the atmospheric emissions regulatory agencies because they relate engine performance to environmental impact. While this procedure is intended to guide the analysis and evaluation of the emissions from aircraft gas turbine engines, the methodology may be applied to the analysis of the exhaust products of any hydrocarbon/air combustor.
CURRENT
2016-03-03
Standard
J2683_201603
This SAE Standard applies to Carbon Dioxide R-744 refrigerant used to service motor vehicle passenger air-conditioning (A/C) systems designed to use CO2 (R-744). Hermetically sealed, refrigerated cargo systems are not covered by this document.
2016-02-29
WIP Standard
AIR6418
The scope of this document will consider a broader range of contaminants than ARP4418. In addition, it may provide guidance for measuring on wing, as well as in test cells, Finally, it may also discuss transient measurements, as well as steady state measurements.
CURRENT
2015-05-26
Standard
AMS2641C
This specification covers two types of refined hydrocarbon compounds in the form of liquids.
CURRENT
2015-04-23
Standard
J2992_201504
The scope of this document focuses on the tests required by EPA to validate the performance of the FTIR system following the section in the Code of Federal Regulations Part 1065 (40CFR1U.1065 and hereafter referred to as “EPA Part 1065”) on the guidelines and performance criteria for various regulated gases. This document focuses on the use of continuous emissions sampling for both Engine and Vehicle testing. Future addenda will be needed to cover bag and other sampling techniques. Gas components that do not currently have performance criteria but may soon be regulated are noted and EPA suggestions as to what should be required are applied. This will help ensure that the FTIR will be recognized as a valid and alternative tool for engine exhaust emissions testing. Components in engine exhaust that are specifically called out in this document include: carbon monoxide (CO), carbon dioxide (CO2), oxides of nitrogen (NO, NO2 and N2O), ammonia (NH3), methane (CH4), and formaldehyde (H2CO).
2015-04-19
WIP Standard
J1115
Historically SAE has been concerned with nomenclature as an integral part of the standards development process. Guidelines for automotive nomenclature were written in 1916, were last revised in 1941, and were included in the SAE Handbook until 1962. The present diversity of groups working on nomenclature in the various ground vehicle committees led to the organization of the Nomenclature Advisory Committee under SAE Automotive Council.
2015-02-13
WIP Standard
ARP4955B
The purpose of this SAE Aerospace Recommended Practice (ARP) is to establish guidelines for the measurement of static and dynamic characteristic properties of aircraft tires. It is intended as a general guide toward standard practice, but may be subject to frequent changes to keep pace with experience and technical advances.
2015-02-11
WIP Standard
ARP1256E
This Aerospace Recommended Practice (ARP) describes the continuous sampling and analysis of gaseous emissions from aircraft gas turbine engines. The measured gas species include carbon monoxide (CO), carbon dioxide (CO₂), nitric oxide (NO), nitrogen dioxide (NO₂), total hydrocarbons (CHα where"α" is the hydrogen to carbon ratio of the fuel) and water vapor (H₂O). This ARP excludes engine operating procedures and test modes, and is not intended for in-flight testing, nor does it apply to engines operating in the afterburning mode. It is recognized that there will probably be major advances in the gas analysis measurement technology. It is not the intent of this ARP to exclude other analysis techniques, but to form the basis of the minimum amount of conventional instruments (those in common industry usage over the last fifteen years) required for the analysis of aircraft engine exhaust.
2015-01-26
WIP Standard
ARP6320
This Aerospace Recommended Practice (ARP) consists of methodologies for the measurement of non-volatile particulate matter (nvPM) emissions at the exit plane of aircraft gas turbine engines. The methods describe means of sampling and measuring particle mass concentration, particle number concentration and reporting of emissions indices through the use of an appropriate sampling system and instrumentation that goes beyond the measurements of visible obscuration as described in ARP 1179 for Smoke Number (SN).
CURRENT
2015-01-23
Standard
J551/1_201501
This SAE Standard covers the measurement of radio frequency radiated emissions and immunity. Each part details the requirements for a specific type of electromagnetic compatibility (EMC) test and the applicable frequency range of the test method. The methods are applicable to a vehicle, boat, machine or device powered by an internal combustion engine or battery powered electric motor. Operation of all engines or motors (main and auxiliary) of a vehicle, boat, machine or device is included. All equipment normally operating when the vehicle, boat, machine or device is in operation is included. Operator controlled equipment is included or excluded as specified in the individual document parts. As a special case, CISPR 12 applies to battery powered floor finishing equipment, but robot carpet sweepers are excluded. By reference, IEC CISPR 12 and CISPR 25 are adopted as the standards for the measurement of vehicle emissions.
CURRENT
2015-01-15
Standard
J2610_201501
The purpose of this SAE Information Report is to specify the requirements necessary to fully define the Serial Data Communication Interface (SCI) used in the reprogramming of emission-related powertrain Electronic Control Units (ECU) in Fiat Chrysler Automobiles (FCA) vehicles. It is intended to satisfy new regulations proposed by the federal U.S. Environmental Protection Agency (EPA) and California Air Resource Board (CARB) regulatory agencies regarding “pass-thru programming” of all On-Board Diagnostic (OBD) compliant emission-related powertrain devices. These requirements are necessary to provide independent automotive service organizations and after-market scan tool suppliers the ability to reprogram emission-related powertrain ECUs for all manufacturers of automotive vehicles. Specifically, this document details the SCI physical layer and SCI data link layer requirements necessary to establish communications between a diagnostic tester and an ECU.
HISTORICAL
2014-08-11
Standard
J1979_201408
This document supersedes SAE J1979 May 2007, and is technically equivalent to ISO 15031-5 2010, with the addition of new capabilities required by revised regulations from the California Air Resources Board and revised regulations from the European Commission. This document is intended to satisfy the data reporting requirements of On-Board Diagnostic (OBD) regulations in the United States and Europe, and any other region that may adopt similar requirements in the future.
CURRENT
2014-06-16
Standard
J1892_201406
This SAE Recommended Practice describes the basic content requirements, bar-code specifications, and functional test specifications of a vehicle emission configuration (VEC) label. On the vehicle, the VEC label is to be mounted under the hood in a readily accessible location for use of a bar-code scanning device. This document specifies a permanent vehicle emission configuration label that can be automatically identified through a bar-coded format.
2014-03-06
WIP Standard
AIR6501
To provide a method that accounts for the attenuation due to line-of-sight blockage of aircraft noise by terrain features.
CURRENT
2014-02-21
Standard
J2191_201402
This SAE document defines a recommended practice for implementing circuit identification for electrical power and signal distribution systems of the Class 8 trucks and tractors. This document provides a description of a supplemental circuit identifier that shall be utilized in conjunction with the original equipment manufacturer’s primary circuit identification as used in wire harnesses but does not include electrical or electronic devices which have pigtails. The supplemental circuit identifier is cross-referenced to a specified subsystem of the power and signal distribution system identified in Section 5.
Viewing 1 to 30 of 372