Criteria

Text:
Content:
Display:

Results

Viewing 211 to 240 of 6150
CURRENT
2017-06-28
Standard
AS47642B
This document establishes techniques for validating that an Aircraft Station Interface (ASI) complies with the interface requirements delineated in MIL-STD-1760C. For validation of aircraft designed to MIL-STD-1760A Notice 2 AS4764 Issued 1995-04 applies. For validation of aircraft designed to MIL-STD-1760B Notice 3 AS47641 Issued 1999-08 applies.
CURRENT
2017-06-28
Standard
AS47641A
This document establishes techniques for validating that an Aircraft Station Interface (ASI) complies with the interface requirements delineated in MIL-STD-1760B Notice 3. For validation of aircraft designed to MIL-STD-1760A Notice 2 AS4764 Issued 1995-04 applies.
2017-06-28
WIP Standard
AS50881G
This specification covers all aspects in electrical wire interconnection systems (EWIS) from the selection through installation of wiring and wiring devices and optical cabling and termination devices used in aerospace vehicles. Aerospace vehicles include manned and unmanned airplanes, helicopters, lighter-than-air vehicles, missiles and external pods.
CURRENT
2017-06-27
Standard
AS4270A
This document establishes techniques for validating that a mission store complies with the interface requirements delineated in MIL-STD-1760.
CURRENT
2017-06-27
Standard
AS4764A
This document establishes techniques for validating that an aircraft station complies with the interface requirements delineated in MIL-STD-1760.
2017-06-27
WIP Standard
J139
To provide standard terminology and definitions with regard to ignition systems for spark-ignited internal combustion engines.
CURRENT
2017-06-26
Standard
J2836/4_201706
This SAE Information Report J2836/4 establishes diagnostic use cases between plug-in electric vehicles and the EV Supply Equipment (EVSE). As Plug-In Vehicles (PEV) are deployed and include both Plug-In Hybrid Electric (PHEV) and Battery Electric (BEV) variations, failures of the charging session between the EVSE and PEV may include diagnostics particular to the vehicle variations. This document will describe the general information required for diagnostics and J2847/4 will include the detail messages to provide accurate information to the customer and/or service personnel to identify the source of the issue and assist in resolution. Existing vehicle diagnostics can also be added and included during this charging session regarding issues that have occurred or are imminent to the EVSE or PEV, to assist in resolution of these items.
2017-06-23
WIP Standard
J2945/3
This effort will serve for the development of a new standard to define requirements to support V2I weather applications interface in a connected vehicle environment. USDOT has provided funding for this standard and has requested that the Technical Committee (TC) approve using the Systems Engineering Process (SEP) as defined in J2945/0. Initial works in the field of road weather applications have been conducted by stakeholders from both the public and private sector. USDOT has offered a high level Concept of Operations for Road Weather Connected Vehicle and Automated Vehicle Applications to the TC as a basis for consideration to initiate the dialog for J2945/3. This Concept of Operations contains 8 Proposed Applications and 13 Operational Scenarios for the TC and V2I TF to consider. The TC also has material in SAE J3067 as a basis for its consideration. The focus is on information exchanges between the infrastructure and connected vehicles.
2017-06-21
WIP Standard
ARIR852
This report sets forth guidance for IP-based onboard networks and systems residing in the Airline Information Services (AIS) and Passenger Information and Entertainment Services (PIES) Domains by establishing a common set of security related data elements and format(s) that are produced by aircraft systems, suitable for use by airline IT and/or avionic supplier analytical ground tools.
2017-06-19
WIP Standard
J2836/6
This SAE Information Report SAE J2836/6™ establishes use cases for communication between plug-in electric vehicles and the EVSE, for wireless energy transfer as specified in SAE J2954. It addresses the requirements for communications between the on-board charging system and the Wireless EV Supply Equipment (WEVSE) in support of detection of the WEVSE, the charging process, and monitoring of the charging process. Since the communication to the charging infrastructure and the power grid for smart charging will also be communicated by the WEVSE to the EV over the wireless interface, these requirements are also covered. However, the processes and procedures are expected to be identical to those specified for V2G communications specified in SAE J2836/1. Where relevant, the specification notes interactions that may be required between the vehicle and vehicle operator, but does not formally specify them.
2017-06-19
WIP Standard
J2847/6
This SAE Recommended Practice SAE J2847-6 establishes requirements and specifications for communications messages between wirelessly charged electric vehicles and the wireless charger. Where relevant, this document notes, but does not formally specify, interactions between the vehicle and vehicle operator. This is the 1st version of this document and captures the initial objectives of the SAE task force. The intent of step 1 is to record as much information on “what we think works” and publish. The effort continues however, to step 2 that allows public review for additional comments and viewpoints, while the task force also continues additional testing and early implementation. Results of step 2 effort will then be incorporated into updates of this document and lead to a republished version. The next revision will address the harmonization between SAE J2847-6 and ISO/IEC 15118-7 to ensure interoperability.
2017-06-19
WIP Standard
J2931/6
This SAE Information Report J2931/6 establishes the requirements for physical and data link layer communications between Plug-in Electric Vehicles (PEV) and the Electric Vehicle Supply Equipment (EVSE).
2017-06-16
WIP Standard
J1113/11
This SAE Standard defines methods and apparatus to evaluate electronic devices for immunity to potential interference from conducted transients along battery feed or switched ignition inputs. Test apparatus specifications outlined in this procedure were developed for components installed in vehicles with 12-V systems (passenger cars and light trucks, 12-V heavy-duty trucks, and vehicles with 24-V systems). Presently, it is not intended for use on other input/output (I/O) lines of the device under test (DUT).
2017-06-15
WIP Standard
J1939-17
This document defines a physical layer having a higher bandwidth capacity than the classic physical layers defined for SAE J1939-14 by using flexible data rates. CAN controllers are now available which support the Flexible Data Rate Frame Format as defined in ISO 11898-1:2015. These controllers and compatible high speed transceivers are required for use on SAE J1939-17 networks. This SAE Recommended Practice is intended for light- and heavy-duty vehicles on- or off-road as well as appropriate stationary applications which use vehicle derived components (e.g., generator sets). Vehicles of interest include but are not limited to: on- and off-highway trucks and their trailers; construction equipment; and agricultural equipment and implements.
2017-06-13
WIP Standard
J2932
This document provides test performance requirements for air disc brake actuators for service and combination service parking brake actuators with respect to function, durability and environmental performance when tested according to SAE J2902.
CURRENT
2017-06-13
Standard
J1113/11_201706
This SAE Standard defines methods and apparatus to evaluate electronic devices for immunity to potential interference from conducted transients along battery feed or switched ignition inputs. Test apparatus specifications outlined in this procedure were developed for components installed in vehicles with 12-V systems (passenger cars and light trucks, 12-V heavy-duty trucks, and vehicles with 24-V systems). Presently, it is not intended for use on other input/output (I/O) lines of the device under test (DUT).
Viewing 211 to 240 of 6150