Criteria

Text:
Content:
Display:

Results

Viewing 5851 to 5880 of 6177
HISTORICAL
1977-01-01
Standard
J1054_197701
This SAE Recommended Practice defines the test conditions, procedures, and minimum design requirements for nominal 6, 12, and 24 V warning lamp alternating flashers.
HISTORICAL
1977-01-01
Standard
J945B_197701
This SAE Standard defines the test conditions, procedures, and minimum design requirements for nominal 6, 12, and 24 V hazard warning flashers. Document cancelled 1999. Information now contained in J1690
HISTORICAL
1977-01-01
Standard
AIR1402
This report defines the guidelines for a COMMON TERMINATION METHOD for aerospace vehicle electrical wiring systems and shows how designers can select a minimum number of different parts, among preferred connecting devices that will satisfy all system requirements while achieving the objective of minimum cost in procurement, assembly and maintenance without compromising quality or reliability.
HISTORICAL
1977-01-01
Standard
AS8005
This SAE Aerospace Standard (AS) applies to all temperature instruments used in aircraft applications and environments. The word ""instruments"" as used in the Standard encompasses only the display device and does not include the temperature sensors. Examples of the types of instruments covered are as follows: 1.1 temperature instruments using a resistance temperature detector for temperature sensing; 1.2 temperature instruments using a thermocouple for temperature sensing; 1.3 temperature instruments using an averaging thermocouple harness for temperature sensing; 1.4 temperature instruments receiving an input from a signal conditioning unit; 1.5 temperature instruments receiving an input from another temperature instrument; and 1.6 temperature instruments receiving an input from other temperature sensing devices.
HISTORICAL
1977-01-01
Standard
J590E_197701
This SAE Standard defines the test conditions, procedures, and minimum design requirements for nominal 6, 12, and 24 V turn signal flashers. Document cancelled in 1999. Information now contained in J1690
HISTORICAL
1976-11-01
Standard
J551D_197611
This SAE Standard covers the measurement of broadband electromagnetic radiation over the frequency range of 30 to 1000 MHz from a vehicle or other device powered by an internal combustion engine or electric motor. Operation of all engines (main and auxiliary) of a vehicle or device is included. All equipment normally operating when the engine is running is also included except operator-controlled equipment, which is excluded. The recommended level applies only to complete vehicles or devices in their final manufactured form. Vehicle mounted rectifiers used for battery charging in electric vehicles are included in this document when operated in their charging mode.
HISTORICAL
1976-11-01
Standard
J378B_197611
This recommended practice covers the requirements for all marine inboard engine wiring assemblies and components. The purpose of this recommended practice is to insure that wiring used on marine engines meets the necessary safety standards of the industry. The recommendations cover methods that may be employed by manufacturers to minimize the possibility that engine wiring may be a source of ignition of explosive or flammable vapors and provide manufacturers installing engine electrical systems sufficient information to design and develop engine wiring harnesses safe for marine usage.
HISTORICAL
1976-10-01
Standard
J702B_197610
This SAE Recommended Practice establishes the recommended locations for the air brake and electrical connections for the back of a truck-tractor and the front of a truck-trailer.
HISTORICAL
1976-09-01
Standard
J92_197609
This SAE Recommended Practice is intended to provide the minimum acceptable criteria for snowmobile hand throttle control systems. This recommendation is not intended to cover competition vehicles nor is it intended to limit development of new and/or improved technology in controls. Although these recommendations are primarily addressed to hand control systems using an outer flexible conduit with a multiple strand inner cable, the basic requirements of freedom of movement, strength, material, etc., will apply to any system.
HISTORICAL
1976-09-01
Standard
J539A_197609
This SAE Recommended Practice is intended to apply to lamps, batteries, heaters, radios, and similar equipment for operation with mobile or automotive diesel engines. Twenty-four V systems have long been used for heavy duty services because 24 V permit operating 12 V systems in series-parallel. Thirty-two V systems have been used for marine, railroad-car lighting, and other uses. Generators, storage batteries, starting motors, lighting, and auxiliary electrical equipment shall be for nominal system ratings of 12, 24, or 32 V as determined by the power requirements of the application. It is recommended that no intermediate voltages be considered. The combination of a 24 V starting motor and two 12 V batteries connected in series for cranking is considered practice where it can be adapted to the installation.
HISTORICAL
1976-09-01
Standard
AS8015
This document defines the minimum performance standards for personnel parachute assemblies to be carried in aircraft or worn by passengers, crew, or parachutists for emergency use. This document covers three types of personnel carrying parachute assemblies and the operating limitations for each.
HISTORICAL
1976-07-15
Standard
ARP891A
This recommended practice establishes a procedure for checking the tempers of aluminum alloys through eddy current conductivity measurements and defines criteria for acceptance or rejection.
HISTORICAL
1976-06-01
Standard
J930B_197606
This SAE Standard applies to all types of heavy-duty storage batteries for use on off-road machines as described in SAE J1116. Included are definitions of industry terms, test procedures, general requirements, application recommendations, standard sizes, overall dimensions, and electrical values.
HISTORICAL
1976-04-01
Standard
J543C_197604
The scope of this document is to provide uniform guidelines for the application of starter motor pinions and ring gears. SAE J543 contains guidelines for the use of diametral pitch gearing. The pinion data shown are based on the Fellows stub tooth system. Refer to ISO 8123, ISO 9457-1, and ISO 9457-2 for module gearing, and corresponding metric dimensions.
CURRENT
1976-03-01
Standard
AIR1404
This AIR discusses the DC resistivity property of EMI gaskets.
HISTORICAL
1976-03-01
Standard
ARP1280
This document will be limited in scope to power transfer units made up of two fixed displacement pumps/motors.
CURRENT
1976-02-01
Standard
AIR1406
CURRENT
1976-01-06
Standard
AIR82
HISTORICAL
1976-01-01
Standard
AS8011
This Aerospace Standard (AS) covers the general minimum performance standards of A-C generators and associated regulators for civil aircraft. The generator is a nominal 120/208-volt, 400-Hz, 3-phase, Y-connected system that provides the primary or backup power for electrical systems. The machine can be a brush or brushless design and is normally air cooled.
HISTORICAL
1975-11-01
Standard
J1127_197511
This standard covers low voltage battery cable intended for use at a nominal system voltage of 60 V DC (25 V AC) or less in surface vehicle electrical systems. The tests are intended to qualify cables for normal applications with limited exposure to fluids and physical abuse.
HISTORICAL
1975-11-01
Standard
J1128_197511
This standard covers low voltage primary cable intended for use at a nominal system voltage of 60 V DC (25 V AC) or less in surface vehicle electrical systems. The tests are intended to qualify cables for normal applications with limited exposure to fluids and physical abuse.
CURRENT
1975-09-01
Standard
AS8001
This Standard covers Bank and Pitch Instruments which measure and display the angular displacement of bank and pitch from a gyroscopic vertical reference. This reference may be pneumatically or electrically driven and be contained within the instrument display case or located remotely. Unless otherwise specified, whenever the term "Instrument" is used, it is to be understood to be the complete system of gyro component, any auxiliary equipment and display.
CURRENT
1975-09-01
Standard
AS8004
This standard covers Turn and Slip Instruments which measure and display the rate of turn about the vertical axis and incorporate an integral slip indicator.
HISTORICAL
1975-08-01
Standard
J680B_197508
The location and operation of instruments and controls herein described are recommended for adoption by manufacturers of trucks and truck-tractors in new or revised designs in order to avoid confusion when drivers shift from one truck to another, to promote safety and convenience, and to simplify design, production, and servicing. This recommended practice shall apply to all on-highway trucks and truck-tractors equipped with power brake systems and having a GVW rating of 26 000 lb or more. Of prime importance in this recommended practice is the basic premise that all controls requiring operation while the vehicle is in motion be located so that the driver can manipulate them with his right hand and keep his left hand on the steering wheel. Controls operated only when the vehicle is not in motion, such as the ignition key, starter switch, and engine shutdown, may be located at the left side of the instrument panel and be manipulated with the driver's left hand.
HISTORICAL
1975-07-01
Standard
J945B_197507
This SAE Standard defines the test conditions, procedures, and minimum design requirements for nominal 6, 12, and 24 V hazard warning flashers. Document cancelled 1999. Information now contained in J1690
HISTORICAL
1975-07-01
Standard
ARP1350
This ARP specifies the methods, equipment, and materials to be used in the installation, mounting, and testing of receptacle connectors used in pressure differential applications requiring an effective connector seal.
HISTORICAL
1975-07-01
Standard
ARP1308
The intent of this ARP is to identify selected electrical connectors, their general application characteristics, and associated configuration options recommended for new design, repair, and retrofit purposes. It is acknowledged that those connectors listed herein will not completely satisfy all aerospace vehicle and equipmetn requirements but optimization of the use of these components will facilitate standardization in the form of maximum utilization of a minimum variety of connectors.
HISTORICAL
1975-07-01
Standard
J590E_197507
This SAE Standard defines the test conditions, procedures, and minimum design requirements for nominal 6, 12, and 24 V turn signal flashers. Document cancelled in 1999. Information now contained in J1690
HISTORICAL
1975-06-01
Standard
AMS3623A
This specification covers an irradiated, thermally-stabilized, flame-resistant modified-polychloroprene rubber in the form of thin-wall tubing. This tubing has been used typically as a flexible, electrical insulation tubing whose diameter can be reduced to a predetermined size by heating to 135 degrees C (275 degrees F) or higher, but usage is not limited to such applications.