Criteria

Text:
Content:
Display:

Results

Viewing 1 to 30 of 211
Standard
2014-06-03
This specification covers concentric lay stranded and rope-lay stranded round electrical conductor fabricated from copper, copper alloy or aluminum. This specification also covers thermocouple extension conductor fabricated from nickel/chromium or nickel/aluminum/manganese. The conductors in this specification are suitable for use in insulated wires used in aerospace and other applications.
Standard
2014-05-01
This specification covers insulated wire for use in external aircraft antennas.
WIP Standard
2014-03-17
This specification establishes the requirements for various types and colors of electrical insulating sleeving that will shrink to a predetermined size upon the application of heat. This specification includes provisions for demonstrating compliance with qualification by certification requirements (see 4. and 7.6), in process inspection, and statistical process control inspections (See 4.4). The continuous operating temperature ratings range from -112 °F to +482 °F (-80 °C to +250 °C). The continuous operating temperature range for each sleeving class is given in the applicable detail specification.
WIP Standard
2014-03-11
This SAE Standard provides the minimum requirements for Primary and Auxiliary jumper cable plug and receptacle for the truck-trailer and converter dolly jumper cable systems. It includes the test procedures, design, and performance requirements.
WIP Standard
2014-02-10
This SAE Standard covers cable, shielded and jacketed, intended for use at a nominal system voltage up to 1000 V (AC rms or DC). It is intended for use in surface vehicle electrical systems.
Standard
2014-02-07
This SAE Standard covers cable, shielded and jacketed, intended for use at a nominal system voltage up to 1000 V (AC rms or DC). It is intended for use in surface vehicle electrical systems.
WIP Standard
2014-02-04
This standard covers low voltage primary cable intended for use at a nominal system voltage of 60 V DC (25 V AC) or less in surface vehicle electrical systems. The tests are intended to qualify cables for normal applications with limited exposure to fluids and physical abuse.
WIP Standard
2013-11-01
This standard covers low voltage battery cable intended for use at a nominal system voltage of 60 V DC (25 V AC) or less in surface vehicle electrical systems. The tests are intended to qualify cables for normal applications with limited exposure to fluids and physical abuse.
Standard
2013-10-09
This standard covers low voltage primary cable intended for use at a nominal system voltage of 60 V DC (25 V AC) or less in surface vehicle electrical systems. The tests are intended to qualify cables for normal applications with limited exposure to fluids and physical abuse.
Standard
2013-06-05
This specification covers flexible extruded, vinyl plastic tubing.
Standard
2013-05-09
This glossary provides accepted definitions for terms commonly used by manufacturers and users of electric wire and cable, and their components, intended for use on aerospace vehicles.
Standard
2013-04-20
Scope is unavailable.
Standard
2013-04-20
Scope is unavailable.
Standard
2013-04-20
Scope is unavailable.
Standard
2013-04-20
Scope is unavailable.
Standard
2013-04-20
This specification covers general requirements for direct current electrically held, environmentally sealed toggle switches for use in alternating current (AC) and direct current (DC) applications.
WIP Standard
2013-04-18
This standard covers ultra thin wall low voltage primary cable intended for use at a nominal system voltage of 60 V DC (60 V AC rms) or less in surface vehicle electrical systems. The tests are intended to qualify cables for normal applications with limited exposure to fluids and physical abuse. This standard covers SAE conductor sizes which usually differ from ISO conductor sizes.
Standard
2013-02-01
This SAE standard establishes the minimum construction and performance requirements for seven conductor 1/8 2/10 4/12 cable for use on trucks, trailers and converter dollies. Where appropriate, the standard refers to two types of cables, (Type F and S, described later in the standard), due to the variation in the performance demands of cables used in flexing and stationary applications. While the document’s title refers to ABS Power to differentiate the document from the SAE J1067 standard that it supersedes, the scope applies to both the primary green cable for powering ABS and lighting and the yellow auxiliary cable of the same construction.
Standard
2012-12-20
This SAE Aerospace Recommended Practice (ARP) shall be limited to information about corrosion caused by fluoride offgassing of fluoropolymer-based wire insulation. It reviews published reports of corrosion caused by this phenomenon, describes scenarios where this may be a concern, mitigation options, and references a test method which can be used to evaluate wire insulations where needed.
Standard
2012-10-24
This SAE Standard establishes the minimum performance and endurance requirements for coiled electrical cables used for hookup between trucks, trailers and dollies. The component standards SAE J2394 (replaced SAE J1067) for cable and SAE J560 for connectors must be consulted to determine the complete performance and endurance requirements of the system. Related TMC Recommended Practices may be consulted for information associated with selection, installation and inspection of these coiled electrical cables. This document is intended to set out requirements for the majority of conditions rather than for specialized applications or environments.
Standard
2012-10-23
This SAE Standard covers unshielded cable intended for use at a nominal system voltage up to 600 V or 1000 V (AC rms or DC). It is intended for use in surface vehicle electrical systems.
Standard
2012-10-18
This standard covers supplemental requirements for low tension primary cable intended for use as Fusible Links (Fuse Links) at a nominal system voltage of 60 V DC (25 V AC) or less in surface vehicle electrical systems. These supplemental requirements are intended to qualify cables for an extreme current overload.
Standard
2012-10-18
This standard covers low voltage battery cable intended for use at a nominal system voltage of 60 V DC (25 V AC) or less in surface vehicle electrical systems. The tests are intended to qualify cables for normal applications with limited exposure to fluids and physical abuse.
Viewing 1 to 30 of 211

Filter

  • Standard
    211