Criteria

Text:
Content:
Display:

Results

Viewing 241 to 270 of 5701
2013-12-04
Article
Engineering simulation software provider ANSYS has signed an agreement to acquire Reaction Design. San Diego, CA-based Reaction Design provides chemistry simulation solutions that enable transportation manufacturers and energy companies to achieve their clean-technology goals by automating the analysis of chemical processes via computer simulation and modeling solutions.
2013-11-24
Article
Researchers devised the tests to prove that active flow control can enhance the performance of a vertical tail enough to allow future designers to reduce the size of the structure for a whole family of airplanes.
2013-11-22
Article
Now that simulation and modeling are common techniques for designing equipment, standards groups are stepping in to add a bit more structure and compatibility for these tools. Two trade associations have paired up to establish a working group that aims to make it simpler to merge engineering analysis with overall systems behavior analysis.
2013-11-13
Article
A forum at the 2013 SEMA Show discussed three approaches to ensure performance parts compliance with federal safety standard No. 126. Panelists also explained how simulation data, and kinematics and compliance measurements, can improve performance parts design.
2013-11-12
Article
Altium Limited's Software Platform Builder delivers ultra rapid prototyping and development for ARM Cortex-M based microcontrollers.
2013-10-31
Article
Combustion simulation has the potential to help engine manufacturers design better engines in less time with less cost.
2013-10-31
Article
The interior supplier showed five concept seats featuring customization via various secondary processes at its fall 2013 fashion show. One such advanced technology, polymer printing, enables Lear designers to create a unique look that is then laminated onto the leather as a 3-µm (118-µin) thick film.
2013-10-30
Article
In an attempt to achieve a balance between Reynolds number, model scale, and tunnel blockage issues, a 1:3 scale heavy-vehicle testing program has been initiated at the Monash University 1.4-MW wind tunnel.
2013-10-30
Article
Ashok Leyland, the Hinduja Group flagship, has sold Defiance Testing & Engineering Services (DTE) to Exova, a provider of testing, calibration, and advisory services. Located near Detroit, DTE was acquired by Ashok Leyland in 2007 and since has experienced consistent and profitable growth, according to the Indian OEM, through a combination of operational efficiency, new customer capture, and focus on adjacent sectors such as construction and off-highway, and defense.
2013-10-24
Article
MSC Software offers an updated version of Adams/Machinery software, a customized analysis software package incorporated in the Adams/View environment that allows users to design and build virtual prototypes from common machinery components.
2013-10-21
Article
Next-generation unmanned air systems will require more performance and must integrate increasing capabilities for guidance control, weaponry, and surveillance—all in a very limited space.
2013-10-18
Article
As the highest-volume car builder in the world, Mattel’s Hot Wheels brand dedicates huge resources to the design of its products. Despite recent advances in digital design tools, these 1/64th-scale replicas of production cars still require the human touch to reach fruition.
2013-10-15
Article
The use of LMS Imagine.Lab AMESim software enables Poclain Hydraulics to simulate transmission behavior, helping its engineers develop answers to given issues faster and at a lower cost.
2013-10-14
Article
dSPACE’s new version of SystemDesk 4.1 software architecture tool ensures reliable and convenient hand offs between OEMs and suppliers who develop embedded software and systems for AUTOSAR-compliant electronic control units (ECUs).
2013-10-11
Article
Concurrent CFD applications, such as FloEFD, automate the most demanding steps associated with preparing and running a simulation, allowing designers to develop models and test the heat dispersion properties of an emerging luminaire design.
2013-10-09
Article
The CEO and founder of the company that won the Automotive X-Prize believes there is room for a new energy-efficient Very Light Car category that employs a highly configurable architecture.
2013-10-01
Article
Maplesoft adds the MapleSim hydraulics library to its product family through a technology partnership with Modelon.
2013-09-30
Article
Featuring a 1.6-L turbocharged GDI engine with hybrid-electric drive, the Niro subcompact crossover was designed in the same city in which it was revealed: Frankfurt, Germany.
2013-09-24
Article
Volvo’s stand at the 2013 Frankfurt Motor Show left no doubt about the design influence for the Concept Coupe unveiled at the show. It was billed as the next-generation P1800, and a version of the 1960s coupe was on prominent display on the Volvo stand, overlooking the concept.
2013-09-24
Article
Renault unveiled the Initiale Paris concept at Frankfurt, designed as a replacement model for the Renault Espace and also to show Renault’s thinking for future high-end vehicles.
2013-09-23
Article
BASF basecoats' XSpark, a new automotive OEM special-effect coating, contains very fine glass particles that reflect light with greater precision, thus creating a pronounced sparkle.
2013-09-23
Article
“It starts with the sketch. You have to have the killer sketch,” explained GM Europe Vice President of Design Mark Adams, for the car that is destined to inspire future cars from Opel and Vauxhall.
2013-09-18
Article
Rising system complexity and shortened development cycles have led to the need for an extension of the existing, classical test methods. The Airbus High Lift Test Department is pursuing virtual testing as an additional, equivalent test means besides existing, established physical means of compliance.
2013-09-11
Article
The curvy Q30 Concept, which debuted Sept. 10 at the Frankfurt Motor Show, serves as the design precursor for Infiniti’s future compact premium entry, production of which is expected to start in Sunderland, U.K., in 2015.
2013-09-05
Article
The 2013 IAA concept vehicle's shapely exterior and plush interior showcasing a dual-view display foreshadow a possible new direction for the production S-Max.
2013-09-04
Article
Engineering efficient gasoline engines is more important than ever. However, using physical testing alone to determine an engine’s maximum efficiency is expensive. Fortunately, simulating knock phenomenon with CAE is more feasible than ever.
2013-08-27
Article
A European Union-funded collaborative research project designed to convert exhaust waste heat into onboard electricity via is moving into the prototype stage, according to Ricardo. The company, a partner in the project (called PowerDriver), reported that recently completed simulation work on a potential automotive application of the thermo-electric generator technology (TGEN) indicates a possible output of 300 W and equivalent fuel savings over the NEDC drive cycle of 2.5%.
2013-08-27
Article
BigLever Software’s Gears 7.2, the latest version of the company’s industry-standard product line engineering (PLE) lifecycle framework, delivers multistage configuration capabilities needed for engineering organizations to create, deliver, maintain, and evolve their entire product family tree based on product line features.
2013-08-22
Article
NASA has selected Rockwell Collins to develop a new software analysis tools for verifying the safety of flight critical systems for future commercial aircraft. Under the terms of the one-year contract, Rockwell Collins will develop a set of software analysis tools, conduct demonstrations, and make recommendations to NASA.
2013-08-21
Article
Frank Popielas, Senior Manager of Advanced Engineering in the Dana Power Technologies Group and head of CAE for Dana, spoke with AEI Assistant Editor Matthew Monaghan about Dana's emphasis on innovation, supported by the right engineering tools.
Viewing 241 to 270 of 5701

Filter

  • Article
    1066