Criteria

Text:
Content:
Display:

Results

Viewing 1 to 30 of 157
CURRENT
2017-09-20
Standard
AMS2550F
This specification covers the enginering requirements for a treatment to provide enhanced corrosion resistance to sheet metal parts, such as brackets, spacers, and washers, fabricated from martensitic corrosion-resistant steels, usually AMS 5504 or AMS 5508 and having hardness not higher than 40 HRC, or ferritic corrosion-resistant steels, usually AMS 5506. The treatment is not recommended for use on parts subject to impact in service.
CURRENT
2017-09-05
Standard
AMS4892D
This specification covers a nickel-copper alloy in the form of castings.
CURRENT
2017-08-25
Standard
AMS4893D
This specification covers a nickel-copper alloy in the form of castings.
CURRENT
2017-08-10
Standard
AMS5540P
This specification covers a corrosion and heat-resistant nickel alloy in the form of sheet, strip, and plate up to 2 inches (50.8 mm), inclusive, in nominal thickness (see 8.4).
2017-08-03
WIP Standard
AMS5643/H1025B
This specification covers a corrosion-resistant steel product in the solution and precipitation heat treated (H1025) condition.
2017-08-03
WIP Standard
AMS5659T
This specification covers a corrosion-resistant steel in the form of bars, wire, forgings, flash welded rings, and extrusions in the solution heat treated condition (see 8.3) 12 inches (305 mm) and under in nominal diameter, thickness or for hexagons, least distance between parallel sides, and having a maximum cross-sectional area of 144 in2 (930 cm2), and stock of any size for forging, flash welded rings, or extruding (see 8.6).
CURRENT
2017-07-20
Standard
AMS5951A
This specification covers a corrosion and heat-resistant nickel based alloy in the form of sheet, strip, and plate 0.020 to 1.0 inch (0.508 to 25.4 mm) in thickness (see 8.5).
CURRENT
2017-07-20
Standard
AMS5930B
This specification covers a premium aircraft-quality, alloy steel in the form of bars, forgings, and forging stock.
CURRENT
2017-07-20
Standard
AMS5862M
This specification covers a corrosion-resistant steel in the form of sheet, strip, and plate 4.0 inches (102 mm) and under in nominal thickness (see 8.5).
CURRENT
2017-07-19
Standard
AMS5825H
This specification covers a corrosion resistant steel in the form of welding wire.
CURRENT
2017-07-17
Standard
AMS2482E
This specification establishes the requirements for a hard aluminum oxide coating, impregnated or codeposited with polytetrafluoroethylene (PTFE) on aluminum alloys.
2017-07-10
WIP Standard
AMS5596M
This specification covers a corrosion and heat-resistant nickel alloy in the form of sheet, strip, foil, and plate 1.00 inch (25.4 mm) and under in thickness (see 8.5).
CURRENT
2017-06-28
Standard
AS21906D
SCOPE IS UNAVAILABLE.
CURRENT
2017-06-28
Standard
AS21912D
SCOPE IS UNAVAILABLE.
CURRENT
2017-06-28
Standard
AS21909E
SCOPE IS UNAVAILABLE.
2017-06-22
WIP Standard
AMS2451/4D
This specification establishes the requirements for brush plating of cadmium by electrodeposition.
CURRENT
2017-06-22
Standard
AMS5568H
This specification covers a corrosion and heat resistant steel in the form of welded tubing.
CURRENT
2017-06-16
Standard
ARP584D
This SAE Aerospace Recommended Practice (ARP) addresses the design, installation, and testing of coiled tube assemblies ranging from 1/4 inch (6.3 mm) to 1.0 inch (25 mm) diameter using CRES tubing per AMS-T-6845, unless otherwise approved by the Procuring Activity. This ARP specifically details three different configurations of coiled tubing. These configurations should be compatible with pressure levels up to 3000 psi (20.7 MPa) upon the completion of the analysis for the actual stress and life requirement of the intended application. However, formal qualification tests are recommended to verify the satisfactory installation, clamping, and the life of each unique design. NOTE: Refer to ARP4146 for information on design of coiled tube assemblies using Titanium tubing.
CURRENT
2017-06-15
Standard
AMS4046G
This specification covers an aluminum alloy in the form of sheet and plate clad on one side.
CURRENT
2017-06-13
Standard
AMS5826E
This specification covers a corrosion and heat-resistant steel in the form of welding wire.
Viewing 1 to 30 of 157

Filter

  • Standard
    157