Criteria

Text:
Display:

Results

Viewing 1 to 30 of 5098
2017-11-07
Technical Paper
2017-36-0226
Rafaela Radünz Lazzari, Lara Justine da Silva, Tarcísio Gelaim, Dalmedson Gaúcho R. de Freitas Filho
Abstract In order to improve the aerodynamic efficiency of a radio-controlled aircraft destined to the SAE BRASIL AeroDesign Competition, this paper's goal is to find an ideal position for a wingtip device known as endplate through computational simulation. Therefore, computational fluid dynamics simulations were performed on a wing, maintaining the same geometry and airfoil in all tests, with and without endplate, varying among four positions - up front, down front, up rear, and down rear. The simulations' results showed that positioning the endplate in the back generates the greatest drag force decrease among the tested configurations, being, therefore, the configuration chosen as more efficient.
2017-11-07
Technical Paper
2017-36-0117
Moisés Tiago Christofoletti, André Morais Ferreira, Desirée Farinelli de Souza, Marcelo Leandro dos Santos
Abstract Use of simulation to predict dynamic behavior of engine mounted components play a key role to assist designer´s decision. This paper presents main steps taken to increase fidelity level of a simulation model in comparison with vibration tests of an ignition coil. Dynamic requirements focused by this work include modal and harmonic analysis. Significant improvements on results were achieved mainly through the inclusion of a fixture on simulation model similarly as used on real shaker. A simulation guideline based on commercial Finite Element Analysis (FEA) software was created which allows engineers to get a better first-time product capability before design freeze avoiding tests recursions.
2017-11-07
Technical Paper
2017-36-0346
Bruno Silva de Lima, Alysson Fernandes Teixeira, Arthur Braga Thiriet, Ramon Molina Valle
Abstract This paper describes a reverse engineering methodology to obtain a three-dimensional (3D) model of an internal geometry of an engine adapted with a torch ignition system. The reverse engineering methodology began with the measurement of the internal geometry from the cylinder head using silicon. Then, the obtained silicone molds were analyzed in a 3D scanner obtaining a cloud of points which was then treated in a commercial CAD software in order to generate de 3D computer model. The virtual geometry obtained was used to run CFD simulations with the torch ignition system. In order to increase the reliability of the results, a comparison between the pressures in the cylinder obtained numerically and experimentally were made. The same procedure was made in the pre-chamber, thus validating the model.
2017-11-07
Technical Paper
2017-36-0167
Alvaro Cesar Garcia, Cleber William Gomes
Abstract The turbocharger has unleashed a new era of highly efficient internal combustion engines and shows the right technology to meet global emissions laws. With a simple concept, the turbocharger can reduce the specific fuel consumption, increase engine power and torque by increasing its volumetric efficiency. By using the energy contained in the exhaust gases, the turbocharger compresses the atmospheric air, increasing its density, so that at the moment of combustion there is a more efficient burning of the fuel injected. The purpose of this paper is to analyze the internal components of the turbocharger and a computer simulation made in Ricardo Software's Waves to analyze differences in fuel consumption, volumetric efficiency, torque and in the power of a turbocharged engine compared to the same engine, but without the turbocharger installed.
2017-10-08
Technical Paper
2017-01-2280
Yuzuru Nada, So Morimoto, Yoshiyuki Kidoguchi, Ryu Kaya, Hideaki Nakano, Shinichi Kobayashi
Abstract The aim of this study is to clarify the mixture formation in the combustion chamber of our developed natural gas engine incorporating the sub-chamber injection system, in which natural gas is directly injected into a combustion sub-chamber in order to completely separate rich mixture in the sub-chamber, suitable for ignition, from ultra-lean mixture in the main chamber. Mixture distributions in chambers with and without sub-chamber were numerically simulated at a variety of operating conditions. The commercial software of Fluent 16.0 was used to conduct simulations based on Reynolds averaged Navier-Stokes equations in an axial 2 dimensional numerical domain considering movements of piston. Non-reactive flow in the combustion chamber was simulated before the ignition timing at an engine speed of 2000 rpm. The turbulence model employed here is standard k-ε model. Air-fuel ratio is set with a lean condition of 30.
2017-10-08
Technical Paper
2017-01-2284
Haifei Zheng
Abstract The potential benefits of reheat burner placed between turbine stages for propulsion system have been recognized for nearly a century. Compared to the conventional non-reheat engines, the turbine inter-guide-vane burner (TIB) engines by using jet-swirl flow scheme (high-G loading) are shown to have a higher specific thrust with no or only small increase in thrust specific fuel consumption. But, it is a known fact that the G loading in the circumferential cavity is inversely proportional to the radius of the circumferential cavity. If one needs to scale this configuration for a larger spool of turbine components, the effeciency of the high G operation and obtained benefits on flame speed will reduce and hence the performance will de-grade.
2017-10-08
Technical Paper
2017-01-2202
Shiyou Yang
Abstract This work presents an application of two sub-models relative to chemical-kinetics-based turbulent pre-mixed combustion modeling approach on the simulation of burn rate and emissions of spark ignition engines. In present paper, the justification of turbulent pre-mixed combustion modeling directly based on chemical kinetics plus a turbulence model is given briefly. Two sub-models relative to this kind of pre-mixed combustion modeling approach are described generally, including a practical PRF (primary reference fuel) chemical kinetic mechanism which can correctly capture the laminar flame speed under a wide range of Ford SI (spark ignition) engines/operating conditions, and an advanced spark plug ignition model which has been developed by Ford recently.
2017-10-08
Technical Paper
2017-01-2194
Mateusz Pucilowski, Mehdi Jangi, Sam Shamun, Martin Tuner, Xue-Song Bai
Abstract Heavy-duty direct injection compression ignition (DICI) engine running on methanol is studied at a high compression ratio (CR) of 27. The fuel is injected with a common-rail injector close to the top-dead-center (TDC) with two injection pressures of 800 bar and 1600 bar. Numerical simulations using Reynold Averaged Navier Stokes (RANS), Lagrangian Particle Tracking (LPT), and Well-Stirred-Reactor (WSR) models are employed to investigate local conditions of injection and combustion process to identify the mechanism behind the trend of increasing nitrogen oxides (NOx) emissions at higher injection pressures found in the experiments. It is shown that the numerical simulations successfully replicate the change of ignition delay time and capture variation of NOx emissions.
2017-10-08
Technical Paper
2017-01-2186
Lukas Urban, Michael Grill, Sebastian Hann, Michael Bargende
Abstract Engine Knock is a stochastic phenomenon that occurs during the regular combustion of spark ignition (SI) engines and limits its efficiency. Knock is triggered by an autoignition of local “hot spots” in the unburned zone, ahead of the flame front. Regarding chemical kinetics, the temperature and pressure history as well as the knock resistance of the fuel are the main driver for the autoignition process. In this paper, a new knock modeling approach for natural gas blends is presented. It is based on a kinetic fit for the ignition delay times that has been derived from chemical kinetics simulations. The knock model is coupled with an enhanced burn rate model that was modified for Methane-based fuels. The two newly developed models are incorporated in a predictive 0D/1D simulation tool that provides a cost-effective method for the development of natural gas powered SI engines.
2017-10-08
Technical Paper
2017-01-2310
Xiaoyan Jia, Baigang Sun, Dongwei Wu, Dan Xu, Wei Zang, Wei Shang, Jie Wang
Abstract The control valve is the most important implementation part of a high pressure common rail system, and its flow characteristics have a great influence on the performance of an injector. In this paper, based on the structure and the working principle of an electromagnetic injector in a high pressure common rail system, a simulation model of the injector is established by AMESim software. Some key parameters of the control valve, including the volume of the control chamber, the diameter of the orifice Z (feeding orifice), the diameter of the orifice A (discharge orifice) and the hole diameter of the fuel diffusion hole are studied by using this model. The results show that these key structural parameters of the control valve have a great influence on the establishment of the control chamber pressure and the action of the needle valve.
2017-09-23
Technical Paper
2017-01-1952
ChengJun Ma, Fang Li, Chenglin Liao, Lifang Wang
Abstract With the load of urban traffic system becomes more serious, the Automatic Parking System (APS) plays an important role in alleviating the burden of drivers and improving vehicle safety. The APS is consisted of environmental perception, path planning and path following. The path following controls the lateral movement of vehicle during the parking process, and requires the trajectory tracking error to be as small as possible. At present, some control algorithms are used including PID control, pure pursuit control, etc. However, these algorithms relying heavily on parameters and environment, have some problems such as slow response and low precision. To solve this problem, a path following control method based on Model Predictive Control (MPC) algorithm is proposed in this paper. Firstly, Kinematic vehicle model and path tracker based on MPC algorithm are built. Secondly, a test bench that composed of CANoe hardware in the loop (HIL) system and steering wheel system is built.
2017-09-19
Technical Paper
2017-01-2025
Eugenio Rodriguez
Abstract One of the most important activities associated with the Aerospace or Defense industry is maintenance. Maintainability procedures have a direct impact on safety and operational availability of systems. The processes and procedures that are used during maintenance activities, whether removing and replacing a component of a system, or conducting troubleshooting, are generally discrete by design, and in most cases, a maintainer, or a field service representative (FSR), will follow a sequence of steps as part of a maintenance work package or work instruction to complete the necessary tasks. Depending on the system, those maintenance activities could be complex, requiring a large maintenance window and the availability of resources to ensure completion.
2017-09-19
Technical Paper
2017-01-2022
Katherine Loundy, Louis Schaefer, Andrew Foran, Catherine Ninah, Khristopher Bandong, Robert Brown, Hunter Heston, John-Paul Steed, William Young, Mark Heinrich, Luis Rabelo
Abstract The future of human exploration in the solar system is contingent on the ability to exploit resources in-situ to produce mission consumables. Specifically, it has become clear that the success of a manned mission to Mars will likely depend on fuel components created on the Martian surface. While several architectures for an unmanned fuel production surface facility on Mars exist in theory, a simulation of the performance and operation of these architectures has not been created. In this paper, the framework describing a simulation of one such architecture is defined. Within this architecture, each component of the base is implemented as a state machine, with the ability to communicate with other base elements as well as a supervisor. An environment supervisor is also created which governs low level aspects of the simulation such as movement and resource distribution, in addition to higher-level aspects such as location selection with respect to operations specific behavior.
2017-09-19
Journal Article
2017-01-2024
Natasha L. Schatzman, Narayanan Komerath, Ethan A. Romander
Abstract The blade crossing event of a coaxial counter-rotating rotor is a potential source of noise and impulsive blade loads. Blade crossings occur many times during each rotor revolution. In previous research by the authors, this phenomenon was analyzed by simulating two airfoils passing each other at specified speeds and vertical separation distances, using the compressible Navier-Stokes solver OVERFLOW. The simulations explored mutual aerodynamic interactions associated with thickness, circulation, and compressibility effects. Results revealed the complex nature of the aerodynamic impulses generated by upper/lower airfoil interactions. In this paper, the coaxial rotor system is simulated using two trains of airfoils, vertically offset, and traveling in opposite directions. The simulation represents multiple blade crossings in a rotor revolution by specifying horizontal distances between each airfoil in the train based on the circumferential distance between blade tips.
2017-09-19
Journal Article
2017-01-2018
Won Il Jung, Larry Lowe, Luis Rabelo, Gene Lee, Ojeong Kwon
Abstract Operator training using a weapon in a real-world environment is risky, expensive, time-consuming, and restricted to the given environment. In addition, governments are under intense scrutiny to provide security, yet they must also strive for efficiency and reduce spending. In other words, they must do more with less. Virtual simulation, is usually employed to solve these limitations. As the operator is trained to maximize weapon effectiveness, the effectiveness-focused training can be completed in an economical manner. Unfortunately, the training is completed in limited scenarios without objective levels of training factors for an individual operator to optimize the weapon effectiveness. Thus, the training will not be effective. For overcoming this problem, we suggest a methodology on guiding effectiveness-focused training of the weapon operator through usability assessments, big data, and Virtual and Constructive (VC) simulations.
2017-09-17
Technical Paper
2017-01-2492
Dejian Meng, Ziyi Wang, Lijun Zhang, Zhuoping Yu
Abstract In this paper, the initial disc thickness variation (DTV) of a ventilated disc in automotive brake system is modeled as sinusoidal function of the second order. The transient thermomechanical coupling properties of the brake system is simulated using finite element (FE) modeling. The system models and results were verified by a thermomechanical coupling test of a disc brake conducted on a brake dynamometer. By using varied evaluation indexes such as the temperature distribution, the normal stress and the elastic deformation of disc surfaces, the influences of the initial DTV and its direction as well as its amplitude on the thermomechanical coupling characteristics were analyzed.
2017-09-16
Journal Article
2017-01-9183
Tine Christiansen, Johanne Jensen, Andreas Åberg, Jens Abildskov, Jakob Huusom
Abstract A methodology for the development of catalyst models is presented. Also, a methodology of the implementation of such models into a modular simulation tool, which simulates the units in succession, is presented. A case study is presented illustrating how suitable models can be found and used for simulations. Such simulations illustrate the behavior of the individual units and the overall system. It is shown how, by simulating the units in succession, the entire after treatment system can be tested and optimized, because the integration makes it possible to observe the effect of the modules on one another.
2017-09-04
Technical Paper
2017-24-0179
Marco Tonetti, Giorgio Rustici, Massimo Buscema, Luca Ferraris
Abstract Final Euro6d emission legislation with the new homologation cycle and Real Driving Emission requirements has set a strong challenge for the ICE Passenger Car applications. Thanks to their well-known low fuel consumption characteristics, Diesel Engines can play a key role for the fulfillment of the European 2020 CO2 fleet target but need to confirm their capability to fully control noxious emissions even in extreme operating conditions, while restraining the overall engine costs and complexity. CO2 and NOx emissions reduction are considered the main drivers for diesel engine evolution. In this perspective, Exhaust Gas After-treatment and Combustion System have been identified as the two main technology aspects to be developed. The purpose of this paper is to describe the evolution paths of these two technologies and the results achieved so far in terms of noxious emissions reduction.
2017-09-04
Technical Paper
2017-24-0139
Francesco Barba, Alberto Vassallo, Vincenzo Greco
Abstract The aim of the present study is to improve the effectiveness of automotive diesel engine and aftertreatment calibration process through the critical evaluation of several methodologies to estimate the soot mass flow produced by diesel engines fueled by petroleum fuels and filtered by Diesel Particulate Filters (DPF). In particular, its focus has been the development of a reliable simulation method for the accurate prediction of the engine-out soot mass flow starting from Filter Smoke Number (FSN) measurements executed in steady state conditions, in order to predict the DPF loading considering different engine working conditions corresponding to NEDC and WLTP cycles. In order to achieve this goal, the study was split into two main parts: Correlation between ‘wet PM’ (measured by soot filter weighing) and the ‘dry soot’ (measured by the Micro Soot Sensor MSS).
2017-06-05
Technical Paper
2017-01-1892
Yosuke Tanabe, Masanori Watanabe, Takafumi Hara, Katsuhiro Hoshino, Akira Inoue, Masaru Yamasaki
Abstract Predicting the vibration of a motor gearbox assembly driven by a PWM inverter in the early stages of development is demanding because the assembly is one of the dominant noise sources of electric vehicles (EVs). In this paper, we propose a simulation model that can predict the transient vibration excited by gear meshing, reaction force from the mount, and electromagnetic forces including the carrier frequency component of the inverter up to 10 kHz. By utilizing the techniques of structural model reduction and state space modeling, the proposed model can predict the vibration of assembly in the operating condition with a system level EV simulator. A verification test was conducted to compare the simulation results with the running test results of the EV.
2017-06-05
Technical Paper
2017-01-1802
Dong chul Lee, Insoo Jung, Jaemin Jin, Stephan Brandl, Mehdi Mehrgou
Abstract In the automotive industry, various simulation-based analysis methods have been suggested and applied to reduce the time and cost required to develop the engine structure to improve the NVH performance of powertrain. This simulation is helpful to set the engine design concept in the initial phase of the powertrain development schedules. However, when using the conventional simulation method with a uniformed force, the simulation results sometimes show different results than the test results. Therefore, in this paper, we propose a method for predicting the radiated noise level of a diesel engine using actual combustion excitation force. Based on the analytical radiated noise development target, we identify the major components of the engine that are beyond this development target by in the frequency range. The components of the problem found in this way are reflected in the engine design of the early development stage to shorten the development time.
2017-06-05
Journal Article
2017-01-1902
Guan Qiao, Geng Liu, Zhenghong Shi, Yawen Wang, Shangjun Ma, Teik Lim
Abstract Actuator and roller screw mechanism are key components of electromechanical brake (EMB) system in automotive and aerospace industry. The inverted planetary roller screw mechanism (IPRSM) is particularly competitive due to its high load-carrying capacity and small assembly size. For such systems, friction characteristic and friction torque generated from rolling/sliding contacts can be an important factor that affects the dynamic performance as well as vibration behavior. This paper investigates the modeling and simulation of the EMB system in early design stage with special attention to friction torque modelling of IPRSM. Firstly, a step-by-step system model development is established, which includes the controller, servo motor, planetary gear train and roller screw mechanism to describe the dynamic behavior of the EMB system.
2017-06-05
Technical Paper
2017-01-1788
Kishore Chand Ulli, Upender Rao Gade
Abstract Automotive window buffeting is a source of vehicle occupant’s discomfort and annoyance. Original equipment manufacturers (OEM) are using both experimental and numerical methods to address this issue. With major advances in computational power and numerical modelling, it is now possible to model complex aero acoustic problems using numerical tools like CFD. Although the direct turbulence model LES is preferred to simulate aero-acoustic problems, it is computationally expensive for many industrial applications. Hybrid turbulence models can be used to model aero acoustic problems for industrial applications. In this paper, the numerical modelling of side window buffeting in a generic passenger car is presented. The numerical modelling is performed with the hybrid turbulence model Scale Adaptive Simulation (SAS) using a commercial CFD code.
2017-03-28
Technical Paper
2017-01-0182
Gautam Peri, Saravanan Sambandan, S. Sathish Kumar
Abstract Cool down of a passenger vehicle cabin is a preferred method to test the efficiency of the vehicle HVAC (Heating, Ventilation and Air Conditioning) system. The intended primary objective of a passenger vehicle air conditioning system is to ensure thermal comfort to the passengers seated inside at all prevailing conditions. Presently 1-D analysis plays a major role in determining the conformation of the selected system to achieve the desired results. Virtual analysis thus saves a lot of time and effort in predicting the system performance in the initial development phase of the vehicle HVAC systems. A variety of parameters play an important role in achieving the above thermal comfort. Thermal comfort is measured using the Human comfort sensor for all the passengers seated inside.
2017-03-28
Technical Paper
2017-01-1225
Jayaraman Krishnasamy, Martin Hosek
Abstract An advanced electric motor with hybrid-field topology has been developed for automotive traction applications. Departing from the conventional radial- and axial-field designs, the hybrid-field motor features three-dimensional magnetic flux paths, which are enabled by a novel isotropic soft magnetic material produced by a unique additive-manufacturing process based on spray forming. The motor is expected to offer an unprecedented combination of high power output, compact size, low weight and energy efficiency, achieving more than two times higher power density than state-of-the-art high-performance traction motors.
2017-03-28
Technical Paper
2017-01-1141
Bashar Alzuwayer, Robert Prucka, Imtiaz Haque, Paul Venhovens
Abstract Fuel economy regulations have forced the automotive industry to implement transmissions with an increased number of gears and reduced parasitic losses. The objective of this research is to develop a high fidelity and a computationally efficient model of an automatic transmission, this model should be suitable for controller development purposes. The transmission under investigation features a combination of positive clutches (interlocking dog clutches) and conventional wet clutches. Simulation models for the torque converter, lock-up clutch, transmission gear train, interlocking dog clutches, wet clutches, hydraulic control valves and circuits were developed and integrated with a 1-D vehicle road load model. The integrated powertrain system model was calibrated using measurements from real-world driving conditions. Unknown model parameters, such as clutch pack clearances, compliances, hydraulic orifice diameters and clutch preloads were estimated and calibrated.
2017-03-28
Technical Paper
2017-01-0903
Sarp Mamikoglu, Jelena Andric, Petter Dahlander
Abstract Many technological developments in automobile powertrains have been implemented in order to increase efficiency and comply with emission regulations. Although most of these technologies show promising results in official fuel economy tests, their benefits in real driving conditions and real driving emissions can vary significantly, since driving profiles of many drivers are different than the official driving cycles. Therefore, it is important to assess these technologies under different driving conditions and this paper aims to offer an overall perspective, with a numerical study in simulations. The simulations are carried out on a compact passenger car model with eight powertrain configurations including: a naturally aspirated spark ignition engine, a start-stop system, a downsized engine with a turbocharger, a Miller cycle engine, cylinder deactivation, turbocharged downsized Miller engine, a parallel hybrid electric vehicle powertrain and an electric vehicle powertrain.
2017-03-28
Journal Article
2017-01-0899
Paul Dekraker, John Kargul, Andrew Moskalik, Kevin Newman, Mark Doorlag, Daniel Barba
Abstract The Environmental Protection Agency’s (EPA’s) Advanced Light-Duty Powertrain and Hybrid Analysis (ALPHA) tool was created to estimate greenhouse gas (GHG) emissions from light-duty vehicles. ALPHA is a physics-based, forward-looking, full vehicle computer simulation capable of analyzing various vehicle types with different powertrain technologies, showing realistic vehicle behavior, and auditing of internal energy flows in the model. In preparation for the midterm evaluation (MTE) of the 2017-2025 light-duty GHG emissions rule, ALPHA has been updated utilizing newly acquired data from model year 2013-2016 engines and vehicles. Simulations conducted with ALPHA provide data on the effectiveness of various GHG reduction technologies, and reveal synergies that exist between technologies. The ALPHA model has been validated against a variety of vehicles with different powertrain configurations and GHG reduction technologies.
2017-03-28
Technical Paper
2017-01-0214
Simon O. Omekanda, Rezwanur Rahman, Eric M. Lott, Sadek S. Rahman, Daniel E. Hornback
Abstract Designing an efficient transient thermal system model has become a very important task in improving fuel economy. As opposed to steady-state thermal models, part of the difficulty in designing a transient model is optimizing a set of input parameters. The first objective in this work is to develop an engine compatible physics-based 1D thermal model for fuel economy and robust control. In order to capture and study the intrinsic thermo-physical nature, both generic “Three Mass” and “Eight Mass” engine models are developed. The models have been correlated heuristically using Simulink. This correlation and calibration process is challenging and time consuming, especially in the case of the 8-mass model. Hence, in this work a Particle Swarm Optimizer (PSO) method has been introduced and implemented on a simple 3-mass and more complex 8-mass engine thermal model in order to optimize the input parameters.
2017-03-28
Journal Article
2017-01-0518
Sebastian Hann, Lukas Urban, Michael Grill, Michael Bargende
Abstract Since 0D/1D-simulations of natural gas spark ignition engines use model theories similar to gasoline engines, the impact of changing fuel characteristics needs to be taken into consideration in order to obtain results of higher quality. For this goal, this paper proposes some approaches that consider the influence of binary fuel mixtures such as methane with up to 40 mol-% of ethane, propane, n-butane or hydrogen on laminar flame speed and knock behavior. To quantify these influences, reaction kinetics calculations are carried out in a wide range of the engine operation conditions. Obtained results are used to update and extend existing sub-models. The model quality is validated by comparing measured burn rates with simulation results. The benefit of the new sub-models are utilized by predicting the influence the fuel takes on engine operating limits in terms of knocking and lean misfire limits, the latter being determined by using a cycle-to-cycle variation model.
Viewing 1 to 30 of 5098

Filter