Criteria

Text:
Content:
Display:

Results

Viewing 1 to 30 of 837
2017-08-16
WIP Standard
J1028
This SAE Recommended Practice applies to stationary usage of mobile construction-type cranes, crawler or rubber-tire mounted, on outriggers or on tires, when used for lifting crane, clamshell, dragline, magnet, pile driver, or similar service.
2017-08-15
WIP Standard
J999
This SAE Standard applies to cranes which are equipped to adjust the boom angle by hoisting and lowering means through rope reeving. The purpose of this standard is to define the function and to stipulate the requirements of an automatic device to prevent raising a variable angle boom above its highest specified angle.
2017-08-15
WIP Standard
J1093
This SAE Information Report applies to wire rope supported, latticed crane boom systems mounted on mobile construction type cranes for lift crane service. The purpose of this document is to establish criteria for the analytical evaluation of the basic structural competence of wire rope supported latticed crane boom systems. The criteria and procedures specified include the evaluation of elastic stability for the overall boom system and individual members of the system.
2017-08-15
WIP Standard
J1939/71
The SAE J1939 communications network is developed for use in heavy-duty environments and suitable for horizontally integrated vehicle industries. The SAE J1939 communications network is applicable for light-duty, medium-duty, and heavy- duty vehicles used on-road or off-road, and for appropriate stationary applications which use vehicle derived components (e.g., generator sets). Vehicles of interest include, but are not limited to, on-highway and off-highway trucks and their trailers, construction equipment, and agricultural equipment and implements.   SAE J1939-71 Vehicle Application Layer is the SAE J1939 reference document for the conventions and notations that specify parameter placement in PGN data fields, the conventions for ASCII parameters, and conventions for PGN transmission rates.
CURRENT
2017-08-14
Standard
J1204_201708
This SAE Recommended Practice provides uniform procedures and minimum performance requirements for fatigue testing ferrous and aluminum wheels intended for normal highway service on travel, camping, and boat and light utility trailers drawn by passenger cars, light trucks, and multipurpose vehicles. For procedures and minimum performance requirements for wheels used on trucks, see SAE J267, and for wheels used on passenger cars, see SAE J328. For the application of passenger car and light truck wheels (inset less than 0.10 m) to this trailer service, use this procedure. For the application of heavier truck wheels (inset 0.10 m (or more)) use SAE J267. Mobile home service is outside the scope of this document. There are two basic test procedures described, a cornering fatigue test and radial fatigue test. The cornering test is directed at the wheel disc; whereas the radial test also examines the rim and attachment portion of the wheel.
CURRENT
2017-08-09
Standard
J701_201708
The information in this SAE Information Report is the result of studies by the Automobile Manufacturers Association, American Trucking Association, and Truck Trailer Manufacturers Association, to achieve interchangeability of equipment which will comply with the legal dimensional limitations for the majority of states and yet permit increased loading space within these dimensions. This in no way supersedes other information in the SAE Handbook on this subject. Some cases will require more care in application allowing splash shield clearance at trailer support interference points and positioning fifth wheel to allow trailer swing clearance on an 11% grade. All dimensions are given in inches. Table 1 and Figures 1 and 2 show basic requirements for interchangeability of truck tractor and semitrailer equipment. Figure 3 shows the interchangeability of the doubles converter dolly.
CURRENT
2017-08-07
Standard
J1014_201708
This SAE Standard includes only those towing winches commonly used on skidders and crawler tractors. These winches are used on self-propelled machines described in SAE J1057, J1116, and J1209. Specifically excluded are those winches used for hoisting operations.
2017-08-01
WIP Standard
J2728
This Recommended Practice (RP) document applies to Heavy Vehicle Event Data Recorders (HVEDR) for heavy-duty (HD) ground wheeled vehicles over 4545 kg (10 000 US pounds), commonly referred to as Class 3-8, which are intended to be compliant with current Federal Motor Vehicle Safety Standards (FMVSS) and/or Federal Motor Carrier Safety Regulations (FMCSR). In the context of the J2728 RP, the term heavy vehicle refers to motor vehicles equipped with one or both of the following vehicle communication networks: SAE J1708/J1587 or SAE J1939. This document is focused primarily on wheeled vehicles with standard on-board power supplies (e.g.,batteries). It is intended to address the needs of OEM original, OEM modified/additive, and aftermarket systems. It does not specifically exclude trailers and similar nonengine powered vehicles, even though the current lack of standardized methodologies and processes for inter-vehicular communication and power supply interconnections remain unresolved.
2017-07-12
WIP Standard
J759
This SAE Recommended Practice provides the lighting function identification codes for use on all passenger vehicles, trucks, trailers, motorcycles, and emergency vehicles.
2017-06-19
WIP Standard
J1992
This SAE Recommended Practice provides minimum performance requirements and uniform laboratory procedures for fatigue testing of disc wheels, demountable rims, and bolt-together divided wheels intended for normal highway use on military trucks, buses, truck-trailers, and multipurpose vehicles. For wheels and rims intended for normal highway use on trucks and buses, see SAE J267. For wheels intended for normal highway use on passenger cars, light trucks, and multipurpose vehicles, see SAE J328. For wheels used on trailers drawn by passenger cars, light trucks, or multipurpose vehicles, see SAE J1204. This document does not cover off-highway or other special application wheels and rims.
CURRENT
2017-06-09
Standard
ARP1804B
This SAE Aerospace Recommended Practice (ARP) outlines the design and performance requirements for a battery-powered electric tow tractor for the handling of baggage or cargo trailers in airline service. The use of “shall” in this document indicates a mandatory requirement. The use of “should” indicates a recommendation or that which is advised but not required.
CURRENT
2017-06-07
Standard
J820_201706
This document applies primarily to mobile cranes that lift loads by means of a drum and hoist line mechanism. It can be used to determine the hoist line speed and power of other hoist line mechanisms, if the load can be held constant and hoist line travel distance is sufficient for the accuracy of the line speed measurements prescribed. This recommended practice applies to all mechanical, hydraulic, and electric powered hoist mechanisms.
CURRENT
2017-06-07
Standard
J765_201706
This SAE Standard may be used for all revolving cranes wherein the capacity of the crane to support loads is based on its resistance to overturning. It is not applicable to cranes wherein the capacity of the crane is based on factors other than stability.
CURRENT
2017-06-05
Standard
J293_201706
This SAE Recommended Practice establishes minimum performance requirements for trucks, buses, truck-tractors, full trailers, and semitrailers with gross vehicle weight ratings greater than 4540 kg (10 000 lb) with regard to: a. Vehicle classification b. Vehicle load c. Percent grade d. Application force
CURRENT
2017-05-19
Standard
J3008_201705
This SAE Standard provides the auxiliary requirements for automotive or RV, additional 12 position, sealed Trailer Tow Connector Plug and Receptacle. The information included within this specification is intended to cover the test methods, design, and performance requirements of optional features for additional power, clean ground for electronic functions, video, data communication, and supplementary electric brake control.
CURRENT
2017-04-18
Standard
J2966_201704
This document outlines general requirements for the use of CFD methods for aerodynamic simulation of medium and heavy commercial ground vehicles weighing more than 10 000lbs. The document provides guidance for aerodynamic simulation with CFD methods to support current vehicle characterization, vehicle development, vehicle concept development and vehicle component development. The guidelines presented in the document are related to Navier-Stokes and Lattice-Boltzmann based solvers. This document is only valid for the classes of CFD methods and applications mentioned. Other classes of methods and applications may or may not be appropriate to simulate the aerodynamics of medium and heavy commercial ground vehicle weighing more than 10 000lbs.
2017-04-10
WIP Standard
J2848/3
This SAE recommended practice defines the system and component functions, measurement metrics, testing methodologies for evaluating the functionality and performance of ground vehicle CTIS. Systems of this type allow the driver to select the operational tire pressure set point (TPSP) based on off-highway conditions, and, upon returning to highway operations, maintain the inflation pressure to the vehicle specified level. These systems are recommended to address all serviceable tires as originally installed on a vehicle by the OEM and/or specialty vehicle manufacturer, and, for the aftermarket (including replacement or spare parts) are recommended (but optional) to address all tire/rim combinations installed after initial vehicle sale or in-use dates.
2017-04-06
WIP Standard
J2848/1
This SAE recommended practice defines the system and component functions, measurement metrics, testing methodologies for evaluating the functionality and performance of tire pressure systems, and recommended maintenance practices within the known operating environments. This document is applicable to all axle and all wheel combinations for single unit powered vehicles exceeding 7257 kg (16 000 US lb) gross vehicle weight rating (GVWR), and multi-unit vehicle combinations, up to three (3) towed units, which use an SAE J560 connector for power and/or communication, or equivalent successor connector technology, or which use a suitable capacity wireless solution. Examples of included single chassis vehicles would be – utility and delivery vans, tow trucks, rack trucks, buses, recreational vehicles, fuel trucks, trash trucks, dump trucks, cement trucks, and tractors.
2017-04-02
WIP Standard
J974
This SAE Standard covers the general requirements and the test requirements for a flashing warning lamp for agricultural equipment.
CURRENT
2017-02-23
Standard
J1301_201702
The scope and purpose of this SAE Recommended Practice is to provide a classification system for deformation sustained by trucks involved in collisions on the highway. Application of the document is limited to medium trucks, heavy trucks, and articulated combinations.1 The TDC classifies collision contact deformation, as opposed to induced deformation, so that the deformation is segregated into rather narrow limits or categories. Studies of collision deformation can then be performed on one or many data banks with assurance that data under study are of essentially the same type.2 Many of the features of the SAE J224 MAR80 have been retained in this document, although the characters within specific columns vary. Each document must therefore be applied to the appropriate vehicle type. It is also important to note that the Truck Deformation Classification (TDC) does not identify specific vehicle configurations and body types.
CURRENT
2017-02-13
Standard
J2611_201702
This SAE information report covers the basic guidelines concerning off-road tire conditions that warrant replacement, removal, or repair. This material can assist the tire user in establishing specific written procedures for each job site.
2017-02-09
WIP Standard
J2247
This SAE Recommended Practice identifies the minimum truck tractor electrical power output of the stop lamp and ABS (antilock brake system) circuits measured at the primary SAE J560 tractor trailer interface connector(s).
CURRENT
2017-02-08
Standard
J48_201702
This SAE Recommended Practice pertains to liquid level determination for any fluid compartment of off-road work machines as defined in SAE J1116 and ISO 6165.
CURRENT
2017-01-18
Standard
J2305_201701
This SAE standard applies to horizontal earthboring machines (SAE J2022) of the following types: Auger boring machines; Rod pushers; Rotary rod machines; Impact machines. This document does not apply to specialized horizontal directional drills, mining machines, conveyors, tunnel boring machines, pipe jacking systems, micro tunnelers, or well drilling machines.
CURRENT
2017-01-17
Standard
J3085_201701
This SAE standard is intended to create standard terminology related to light and medium duty trailer applications. This includes such trailer types as utility, boat, camping, travel, and special purpose trailers which are normally towed by conventional passenger cars, light-duty commercial vehicles, light trucks, and multipurpose passenger vehicles.
CURRENT
2017-01-06
Standard
J167_201701
This SAE Standard applies to an overhead cover installed on a protective frame or enclosure conforming to SAE J2194 or alternately SAE J1194 and the following additional requirement of a drop test to verify the effectiveness of the overhead cover in protecting the operator from falling objects. The test procedures and performance requirements outlined in this document are based on currently available engineering data.
2016-12-17
WIP Standard
J2394
This SAE standard establishes the minimum construction and performance requirements for seven conductor 1/8 2/10 4/12 cable for use on trucks, trailers and converter dollies. Where appropriate, the standard refers to two types of cables, (Type F and S, described later in the standard), due to the variation in the performance demands of cables used in flexing and stationary applications. While the document’s title refers to ABS Power to differentiate the document from the SAE J1067 standard that it supersedes, the scope applies to both the primary green cable for powering ABS and lighting and the yellow auxiliary cable of the same construction.
CURRENT
2016-12-09
Standard
J1790_201612
The SAE Standard applies to self-propelled, driver-operated sweepers and scrubbers as defined in SAE J2130-1 and SAE J2130-2.
2016-12-07
WIP Standard
J983
This SAE Recommended Practice applies to mobile, construction type, crane and cable excavator hand and foot controls. It should not be construed to limit the use of, or to apply to combination controls, automatic controls, or any other special operating control requirements.
CURRENT
2016-12-06
Standard
J1939/11_201612
This document defines a physical layer having a robust immunity to EMI and physical properties suitable for harsh environments. CAN controllers are available which support the CAN Flexible Data Rate Frame Format. These controllers, when used on SAE J1939-11 networks, must be restricted to use only the Classical Frame Format compliant to ISO 11898-1:2015. These SAE Recommended Practices are intended for light- and heavy-duty vehicles on- or off-road as well as appropriate stationary applications which use vehicle derived components (e.g., generator sets). Vehicles of interest include but are not limited to: on- and off-highway trucks and their trailers; construction equipment; and agricultural equipment and implements.
Viewing 1 to 30 of 837