Criteria

Text:
Content:
Display:

Results

Viewing 1 to 30 of 530
2017-08-18
WIP Standard
AMS2435H
This specification covers the engineering requirements for applying tungsten carbide/cobalt coatings to metal parts by the detonation process and the properties of such coatings. This coating has been used typically to provide a hard, wear resistant surface on metal parts which do not operate in service higher than 1000 degrees F (538 degrees C) but usage is not limited to such applications. These coatings are not recommended for surfaces with deep vee-shaped grooves, blind cavities, narrow holes or sharp corners, or where deformation of the base metal may be expected. Higher cobalt content provides increased ductility for applications where impact or fretting wear is involved.
2017-08-18
WIP Standard
AMS2510F
This specification covers the engineering requirements for finishng aircraft parts and assemblies with an engine gray enamel.
CURRENT
2017-07-17
Standard
AMS2482E
This specification establishes the requirements for a hard aluminum oxide coating, impregnated or codeposited with polytetrafluoroethylene (PTFE) on aluminum alloys.
CURRENT
2017-07-14
Standard
AIR5479B
This SAE Aerospace Information Report (AIR) describes the performance of plating’s and coatings for landing gear that potentially provide environmental compliance benefits versus the current baseline processes. The hazardous systems addressed in this version of the document include cadmium plating, chromated primers, and high VOC (volatile organic compounds) topcoats. The AIR applies to landing gear structures and mechanisms for all types of civil and military aircraft. The potential replacements apply to both Original Equipment Manufacturer (OEM) hardware and overhaul of in-service landing gears.
2017-06-22
WIP Standard
AMS2451/4D
This specification establishes the requirements for brush plating of cadmium by electrodeposition.
CURRENT
2017-06-08
Standard
AS7109/7B
This document has been declared "CANCELLED" as of June 2017 and has been superseded by PRI AC7109/7. By this action, this document will remain listed in the Numerical Section of the Aerospace Standards Index noting that it is superseded by PRI AC7109/7. Cancelled specifications are available from SAE.
CURRENT
2017-06-08
Standard
AS7109/6B
This document has been declared "CANCELLED" as of June 2017 and has been superseded by PRI AC7109/6. By this action, this document will remain listed in the Numerical Section of the Aerospace Standards Index noting that it is superseded by PRI AC7109/6. Cancelled specifications are available from SAE.
CURRENT
2017-06-07
Standard
AS7109/4B
This document has been declared "CANCELLED" as of June 2017 and has been superseded by PRI AC7109/4. By this action, this document will remain listed in the Numerical Section of the Aerospace Standards Index noting that it is superseded by PRI AC7109/4. Cancelled specifications are available from SAE.
CURRENT
2017-06-07
Standard
AS7109/5B
This document has been declared "CANCELLED" as of June 2017 and has been superseded by PRI AC7109/5. By this action, this document will remain listed in the Numerical Section of the Aerospace Standards Index noting that it is superseded by PRI AC7109/5. Cancelled specifications are available from SAE.
CURRENT
2017-06-07
Standard
AS7109/3B
This document has been declared "CANCELLED" as of June 2017 and has been superseded by PRI AC7109/3. By this action, this document will remain listed in the Numerical Section of the Aerospace Standards Index noting that it is superseded by PRI AC7109/3. Cancelled specifications are available from SAE.
CURRENT
2017-06-07
Standard
AS7109/1B
This document has been declared "CANCELLED" as of June 2017 and has been superseded by PRI AC7109/1. By this action, this document will remain listed in the Numerical Section of the Aerospace Standards Index noting that it is superseded by PRI AC7109/1. Cancelled specifications are available from SAE.
CURRENT
2017-06-07
Standard
AS7109/2B
This document has been declared "CANCELLED" as of June 2017 and has been superseded by PRI AC7109/2. By this action, this document will remain listed in the Numerical Section of the Aerospace Standards Index noting that it is superseded by PRI AC7109/2. Cancelled specifications are available from SAE.
2017-05-10
WIP Standard
J1173
This specification covers the characteristics of glass beads used for peening, and provides for standard glass bead size numbers. The glass bead classification number is the approximate nominal diameter of the glass spheres in that classification, in hundredths of a millimeter, with the prefix GB added. Glass beads used for peening shall be made from high quality glass of the soda-lime type. They should be as resistant as possible to breakage from shock-impact, or by abrasion during shipment and handling. The particles should be substantially round, free-flowing, and free from chemical impurities or contaminants that might be detrimental to the workpiece.
2017-05-10
WIP Standard
J2597
This SAE Recommended Practice defines a procedure for the use of computer generated saturation curves to determine peening intensity. Calculation of intensity within a tolerance band for each data set in Table 1 one is required for compliance with this practice.
2017-04-24
WIP Standard
G916AB
This specification covers the standard contaminant used to test the cleaning ability of aerospace cleaners.
CURRENT
2017-04-20
Standard
AMS2465D
This specification covers the procedure for applying a disilicide diffusion coating to molybdenum alloy parts by the pack cementation method and the properties of the coating so deposited.
2017-04-19
WIP Standard
AMS2447E
This specification covers the requirements for thermal spray coatings applied using the high velocity oxygen fuel (HVOF) combustion process. This specification is not intended to be used for duplex coatings, i.e., the application of the coating over a previously applied coating.
CURRENT
2017-03-21
Standard
AMS03_3A
This SAE Standard specifies the requirements for the application of sprayed metal coatings of aluminum, zinc, or aluminum-zinc based alloys for the protection of aluminum alloys against corrosion. It does not cover the metal spraying of aluminum armour materials, which should be treated in accordance with the requirements of Def Stan 08-39.
CURRENT
2017-03-21
Standard
AMS03_040A
This SAE Standard specifies the guidance and the requirements for the electrodeposition of zinc-nickel alloy coatings on a range of metallic substrates for the provision of corrosion resistance to steel components and galvanic compatibility between some bi-metallic contacting surfaces.
CURRENT
2017-03-17
Standard
AMS2451/4C
This specification establishes the requirements for brush plating of cadmium by electrodeposition.
2017-03-16
WIP Standard
AMS1388B
This specification covers two types of thickened, water base temporary coating remover in the form of an alkaline liquid. This product has been used typically for removing temporary coatings used for protection of aircraft skins from exposure to processing damage, but usage is not limited to such applications.
CURRENT
2017-02-21
Standard
AS7489
This standard establishes the minimum requirements for training, examination, and certification of aerospace coatings application personnel applying liquid organic coatings to interior structural or exterior substrates. It establishes criteria for the certification of personnel requiring appropriate knowledge of the technical principles underlying aircraft surface preparation and coatings application for both protective and decorative purposes. Persons certified under this document shall receive documentation of certification by the Certifying Agency. Persons who successfully complete the requirements of this certification standard are considered to be able to successfully and consistently perform a broad spectrum of aerospace coatings application tasks to achieve the desired engineering purposes.
CURRENT
2017-02-10
Standard
AMSSTD595A
This standard defines a color index system used by, but not limited to, Government activities in a format suitable for color identification, color selection, color matching, and quality control inspection. It also describes the designation and use of color media that is available to conduct these activities. Use of the color index referenced in this standard is intended to promote standardization and consistency in the color of items produced for Government use. Color media is described as follows: Color Chip Representation, Fan Deck: Suitable for color identification and selection. Color Chip Representation, Color Book: Suitable for color identification and selection. Precise Color Matching, Individual Color Chips: Suitable for color matching and quality control inspection purposes. Precise Color Matching, Set of Color Chips: Suitable for color matching and quality control inspection purposes.
CURRENT
2017-02-07
Standard
AMS2503G
This specification covers the engineering requirements for finishing aircraft parts and assemblies with a black enamel.
2016-11-18
WIP Standard
J100
This SAE Recommended Practice establishes boundaries for shade bands on glazed surfaces in class "A" vehicles. These boundaries are located so that the shade band can provide occupant comfort and driver vision protection from glare, with respect to solar radiation, under some lighting and driving conditions. Since shade bands transmit less visible light than adjacent glazed surfaces, the shade band boundaries establish boundaries for the driver's field of view.
CURRENT
2016-11-17
Standard
AMS3136F
This specification covers a pigmented phenolic-resin-base coating material, filled with polytetrafluoroethylene (PTFE), supplied in kit form.
CURRENT
2016-11-15
Standard
J100_201611
This SAE Recommended Practice establishes boundaries for shade bands on glazed surfaces in class "A" vehicles. These boundaries are located so that the shade band can provide occupant comfort and driver vision protection from glare, with respect to solar radiation, under some lighting and driving conditions. Since shade bands transmit less visible light than adjacent glazed surfaces, the shade band boundaries establish boundaries for the driver's field of view.
2016-11-04
WIP Standard
AMS3138E
This specification covers fluorocarbon (FKM) elastomeric coating materials for fiber-reinforced-resin composite structures in the form of two-component brushable or sprayable liquids.
CURRENT
2016-10-24
Standard
AMS3278B
This specification covers polyurethane (PUR) in the form of two-component sealing compounds.
CURRENT
2016-10-11
Standard
AMS3801/5C
This specification covers one weight and one weave of low-modulus resin treated meta-aramid cloth.
Viewing 1 to 30 of 530

Filter

  • Standard
    530