Criteria

Text:
Topic:
Content:
Display:

Results

Viewing 211 to 240 of 1592
CURRENT
2014-09-09
Standard
J2522_201409
This SAE Recommended Practice defines an Inertia Dynamometer Test procedure that assesses the effectiveness behavior of a friction material with regard to pressure, temperature and speed for motor vehicles fitted with hydraulic brake actuation.
HISTORICAL
2014-08-28
Standard
J1704_201408
This SAE Standard covers motor vehicle brake fluids of the nonpetroleum type, based upon glycols, glycol ethers, and borates of glycolethers, and appropriate inhibitors, for use in the braking system of any motor vehicle such as a passenger car, truck, bus, or trailer. These fluids are not intended for use under arctic conditions. These fluids are designed for use in braking systems fitted with rubber cups and seals made from styrene-butadiene rubber (SBR), or a terpolymer of ethylene, propylene, and a diene (EPDM).
HISTORICAL
2014-08-28
Standard
J1703_201408
This SAE Standard covers motor vehicle brake fluids of the nonpetroleum type, based upon glycols, glycolethers and appropriate inhibitors, for use in the braking system of any motor vehicle such as a passenger car, truck, bus, or trailer. These fluids are not intended for use under arctic conditions. These fluids are designed for use in braking systems fitted with rubber cups and seals made from styrene-butadiene rubber (SBR), or a terpolymer of ethylene, propylene, and a diene (EPDM).
2014-08-26
WIP Standard
J2547
This SAE Standard covers the minimum requirements for nonmetallic tubing as manufactured for use in air brake systems which tubing is different from that described in SAE J844. It is not intended to cover tubing for any portion of the system which operates continuously below - 40 degrees C or above +93 degrees C, above a maximum working gage pressure of 1.0 MPa, or in an area subject to attack by battery acid. This tubing is intended for use in the brake system for connections, which maintain a basically fixed relationship between components during vehicle operation. Coiled tube assemblies required for those installations where flexing occurs are covered by this document, SAE J1131 and SAE J2494-3, to the extent of setting minimum requirements on the essentially straight tube and tube fitting connections which are used in the construction of such assemblies.
CURRENT
2014-08-26
Standard
J109_201408
This SAE Recommended Practice establishes performance requirements for the service brake systems of all classes of motorcycles intended for highway use.
CURRENT
2014-08-20
Standard
J1789_201408
This SAE Standard applies to self-propelled, rider operated, sweepers and scrubbers as defined in SAE J2130 with maximum machine level surface speeds up to 32 km/h. Machines capable of speeds equal to and greater than 32 km/h are not covered by this document.
HISTORICAL
2014-08-11
Standard
J1939DA_201408
The J1939 Digital Annex The J1939 Digital Annex, introduced in August 2013, offers key J1939 technical data in an Electronic Spreadsheet that can be easily searched, sorted, and adapted to other formats. J1939DA contains all of the SPNs (parameters), PGNs (messages), and other J1939 data previously published in the SAE J1939 top level document. J1939DA also contains all of the SLOTs, Manufacturer ID Codes, NAME Functions, and Preferred Addresses previously published in the SAE J1939 top level and the J1939-71 document. J1939DA contains the complete technical details for all of the SPNs and PGNs previously published in the SAE J1939-71 document. For all other SPNs and PGNs which are published in a document other than SAE J1939-71, J1939DA lists only basic details along with a reference to the document that contains the complete technical details. J1939DA replaces, and expands upon, the 1939 Companion Spreadsheet (CS1939), which was last published through November 2012.
CURRENT
2014-07-30
Standard
J2475_201407
This recommended practice contains dimensions and tolerances for spindles in the interface area. Interfacing components include axle spindle, bearing cones, bearing spacer, seal and wheel hub. This recommended practice is intended for axles commonly used on Class 7 and 8 commercial vehicles. Included are SAE axle configurations FF, FL, I80, L, N, P, R, U, and W.
CURRENT
2014-07-29
Standard
AIR5372A
This SAE Aerospace Information Report (AIR) describes the design approaches used for current applications of aircraft Brake-by-Wire (BBW) control systems. The document also discusses the experience gained during service, and covers system, ergonomic, hardware, and development aspects. The document includes the lessons that have been learned during application of the technology. Although there are a variety of approaches that have been used in the design of BBW systems, the main focus of this document is on the current state of the art systems.
CURRENT
2014-07-11
Standard
AS1188A
This specification covers minimum design and test requirements for aircraft tire inflation-deflation equipment for use on all types of aircraft. It shall be the responsibility of the airframe manufacturer to determine the compatibility of the requirement with the applicable aircraft and to specify requirements in excess of these minimums as necessary.
2014-07-02
WIP Standard
J2505
This SAE Recommended Practice provides guidelines for procedures and practices used to obtain and record measurements and to analyze and present results of frictional drag tests of a vehicle with its brakes fully applied at a given roadway location. It is for use at accident sites and test sites and is applicable to straight-line stopping of vehicles such as passenger cars, light trucks and vans under fully braked conditions including locked-wheel skids for vehicles with a conventional braking system and for vehicles with full or partial antilock braking systems (ABS). The average deceleration resulting from a given series of tests is intended to be representative of a frictional drag factor for the conditions under which the test was conducted such as the type of vehicle, type and condition of tires, roadway material and roadway surface conditions. The frictional drag factor is intended to conform to use with the stopping distance formula (Fricke, 1990) as stated in Equation 1.
CURRENT
2014-06-16
Standard
J1892_201406
This SAE Recommended Practice describes the basic content requirements, bar-code specifications, and functional test specifications of a vehicle emission configuration (VEC) label. On the vehicle, the VEC label is to be mounted under the hood in a readily accessible location for use of a bar-code scanning device. This document specifies a permanent vehicle emission configuration label that can be automatically identified through a bar-coded format.
CURRENT
2014-06-16
Standard
ARP5265B
This SAE Aerospace Recommended Practice (ARP) sets forth criteria for the installation, inflation, inspection, and maintenance of aircraft tires as well as criteria for the maintenance of the operating environment so as to achieve the purpose stated in 1.1. (Definitions of terms related to aircraft tires are found in 2.2.)
CURRENT
2014-06-10
Standard
AIR5914
This SAE Aerospace Information Report (AIR) provides guidelines for the development of landing gear fatigue spectra for the purpose of designing and certification testing of Part 25 landing gear. Many of the recommendations herein are generalizations based on data obtained from a wide range of landing gears. The aircraft manufacturer or the landing gear supplier is encouraged to use data more specific to their particular undercarriage whenever possible.
CURRENT
2014-06-06
Standard
J2673_201406
This SAE Recommended Practice describes a test method for determination of heavy truck (Class VI, VII, and VIII) tire force and moment properties under straight-line braking conditions. The properties are acquired as functions of normal force and slip ratio using a sequence specified in this practice. At each normal force increment, the slip ratio is continually changed by application of a braking torque ramp. The data are suitable for use in vehicle dynamics modeling, comparative evaluations for research and development purposes, and manufacturing quality control.
2014-06-02
WIP Standard
J901
The following definitions and illustrations are intended to establish common nomenclature and terminology for universal joints and driveshafts used in various driveline applications. In addition, useful guidelines are included for the application of universal joints and driveshafts. For more specific details, see Universal Joint and Driveshaft Design Manual, AE-7.
CURRENT
2014-05-16
Standard
J1247_201405
This SAE Recommended Practice establishes a uniform procedure for a flat-road simulation of a mountain-fade test of the brake systems of light-duty trucks and multipurpose passenger vehicles up to and including 4500 kg (10 000 lb) GVW and all classes of passenger cars.
CURRENT
2014-05-16
Standard
J1060_201405
This SAE Recommended Practice establishes a rating scale for subjective evaluations of noise and discomfort in motor vehicles. Through test procedures utilizing specific vehicles on specific roads, the scale may be utilized to assess the relative contributions of tires to noise and discomfort. The noise and ride comfort characteristics attributed to automotive tires have traditionally been estimated by subjectively assigning number designations (commonly on a 1 to 10 scale) to the audible and tactile sensations observed while traversing a given road course in a vehicle equipped with the tires under evaluation. Regardless of advances in objective measurements of tire properties related to noise and discomfort, subjective evaluation will continue to be necessary for the purpose of establishing the significance of such measurements.
CURRENT
2014-05-16
Standard
J57_201405
This procedure provides for the measurement of the sound generated by a test tire, mounted on a single-axle trailer, operated at multiple speeds.
CURRENT
2014-05-07
Standard
J1512_201405
These performance requirements have been established for manual slack adjusters when tested to SAE J1461.
CURRENT
2014-04-28
Standard
J1461_201404
This SAE Recommended Practice is intended for testing of manual slack adjusters as they are used in service, emergency, or parking brake systems for vehicles that can be licensed for on-road use.
2014-04-21
WIP Standard
J1705
This SAE Recommended Practice was prepared by the Motor Vehicle Brake Fluids Subcommittee of the SAE Hydraulic Brake Systems Actuating Committee to provide engineers, designers, and manufacturers of motor vehicles with a set of minimum performance standards in order to assess the suitability of silicone and other low water tolerant type brake fluids (LWTF) for use in motor vehicle brake systems. These fluids are designed for use in braking systems fitted with rubber cups and seals made from natural rubber (NR), styrene-butadiene rubber (SBR), or a terpolymer of ethylene, propylene, and a diene (EPDM). In the development of the recommended requirements and test procedures contained herein, it is concluded that the LWTFs must be functionally compatible with existing motor vehicle brake fluids conforming to SAE J1703 and with braking systems designed for such fluids. To utilize LWTFs to the fullest advantage, they should not be mixed with other brake fluids.
CURRENT
2014-04-16
Standard
J2246_201404
This SAE Information Report provides information applicable to production Original Equipment Manufacturer antilock braking systems found on some past and current passenger cars and light trucks. It is intended for readers with a technical background. It does not include information about aftermarket devices or future antilock brake systems. Information in this document reflects that which was available to the committee at the time of publication.
2014-04-01
WIP Standard
J2204
This SAE Standard applies to the usage of tires of the same nominal size and tread type, but with different outside diameter for articulated front-end loaders. Articulated four-wheel-drive front-end loader performance and component life can be affected by excessive differences in the tire outside circumference and/or diameter. The purpose is to provide specific guidelines for the usage of tires with different outside circumference and/or diameter on articulated front-end loaders.
2014-03-07
WIP Standard
J1047
This SAE Recommended Practice covers the tubing intended primarily for use as hydraulic brake lines on motor vehicles. It covers materials, manufacturing processes, and general properties required to meet the wide range of service encountered in automotive applications. To meet this need, it must be formed, assembled, handled, and installed in accordance with sound engineering and manufacturing practices. This specification covers only the basic tubing and does not include attachments such as protective armor or end fittings. This document is not intended to be used for quality control purposes. Design guidelines are shown in Appendix A.
2014-03-05
WIP Standard
J1729
This SAE Recommended Practice provides a test method and instructions for measuring performance of parking brakes on air- or hydraulic-braked vehicles equipped with in-wheel or drive-line parking brakes. This procedure applies to truck tractors, trailers, trucks and buses.
HISTORICAL
2014-02-27
Standard
J1939DA_201402
The J1939 Digital Annex The J1939 Digital Annex, introduced in August 2013, offers key J1939 technical data in an Electronic Spreadsheet that can be easily searched, sorted, and adapted to other formats. J1939DA contains all of the SPNs (parameters), PGNs (messages), and other J1939 data previously published in the SAE J1939 top level document. J1939DA also contains all of the SLOTs, Manufacturer ID Codes, NAME Functions, and Preferred Addresses previously published in the SAE J1939 top level and the J1939-71 document. J1939DA contains the complete technical details for all of the SPNs and PGNs previously published in the SAE J1939-71 document. For all other SPNs and PGNs which are published in a document other than SAE J1939-71, J1939DA lists only basic details along with a reference to the document that contains the complete technical details. J1939DA replaces, and expands upon, the 1939 Companion Spreadsheet (CS1939), which was last published through November 2012.
CURRENT
2014-02-21
Standard
J2191_201402
This SAE document defines a recommended practice for implementing circuit identification for electrical power and signal distribution systems of the Class 8 trucks and tractors. This document provides a description of a supplemental circuit identifier that shall be utilized in conjunction with the original equipment manufacturer’s primary circuit identification as used in wire harnesses but does not include electrical or electronic devices which have pigtails. The supplemental circuit identifier is cross-referenced to a specified subsystem of the power and signal distribution system identified in Section 5.
CURRENT
2014-02-17
Standard
J2812_201402
This SAE Recommended Practice describes an evaluation procedure for validating tire models for use in road load simulations and assesses the relevant dynamic behavior of tires. The laboratory test utilized is a “cleat” test, where a rolling tire on a drum encounters a cleat and the resulting dynamic forces and moments are measured. This test is described in SAE J2730, “Dynamic Cleat Test with Perpendicular and Inclined Cleats”. The test is commonly used to identify tire model parameters. In this recommended practice, requirements for the measurement of the tire’s response are described along with data processing techniques and calculations used to quantitatively compare the tire model’s calculated response to the tire’s response measured on test. This recommended practice addresses both the tire model structure and its parameters.
CURRENT
2014-02-05
Standard
J1911_201402
This SAE Recommended Practice provides instructions and test procedures for air braked vehicles including but not limited to trucks, truck-tractors, trailers, dollies, and buses used on highways but does not include off-highway vehicles.
Viewing 211 to 240 of 1592