Criteria

Text:
Topic:
Content:
Display:

Results

Viewing 181 to 210 of 1543
2014-06-02
WIP Standard
J901
The following definitions and illustrations are intended to establish common nomenclature and terminology for universal joints and driveshafts used in various driveline applications. In addition, useful guidelines are included for the application of universal joints and driveshafts. For more specific details, see Universal Joint and Driveshaft Design Manual, AE-7.
CURRENT
2014-05-16
Standard
J1247_201405
This SAE Recommended Practice establishes a uniform procedure for a flat-road simulation of a mountain-fade test of the brake systems of light-duty trucks and multipurpose passenger vehicles up to and including 4500 kg (10 000 lb) GVW and all classes of passenger cars.
CURRENT
2014-05-16
Standard
J57_201405
This procedure provides for the measurement of the sound generated by a test tire, mounted on a single-axle trailer, operated at multiple speeds.
CURRENT
2014-05-16
Standard
J1060_201405
This SAE Recommended Practice establishes a rating scale for subjective evaluations of noise and discomfort in motor vehicles. Through test procedures utilizing specific vehicles on specific roads, the scale may be utilized to assess the relative contributions of tires to noise and discomfort. The noise and ride comfort characteristics attributed to automotive tires have traditionally been estimated by subjectively assigning number designations (commonly on a 1 to 10 scale) to the audible and tactile sensations observed while traversing a given road course in a vehicle equipped with the tires under evaluation. Regardless of advances in objective measurements of tire properties related to noise and discomfort, subjective evaluation will continue to be necessary for the purpose of establishing the significance of such measurements.
CURRENT
2014-05-07
Standard
J1512_201405
These performance requirements have been established for manual slack adjusters when tested to SAE J1461.
CURRENT
2014-04-28
Standard
J1461_201404
This SAE Recommended Practice is intended for testing of manual slack adjusters as they are used in service, emergency, or parking brake systems for vehicles that can be licensed for on-road use.
2014-04-21
WIP Standard
J1705
This SAE Recommended Practice was prepared by the Motor Vehicle Brake Fluids Subcommittee of the SAE Hydraulic Brake Systems Actuating Committee to provide engineers, designers, and manufacturers of motor vehicles with a set of minimum performance standards in order to assess the suitability of silicone and other low water tolerant type brake fluids (LWTF) for use in motor vehicle brake systems. These fluids are designed for use in braking systems fitted with rubber cups and seals made from natural rubber (NR), styrene-butadiene rubber (SBR), or a terpolymer of ethylene, propylene, and a diene (EPDM). In the development of the recommended requirements and test procedures contained herein, it is concluded that the LWTFs must be functionally compatible with existing motor vehicle brake fluids conforming to SAE J1703 and with braking systems designed for such fluids. To utilize LWTFs to the fullest advantage, they should not be mixed with other brake fluids.
CURRENT
2014-04-16
Standard
J2246_201404
This SAE Information Report provides information applicable to production Original Equipment Manufacturer antilock braking systems found on some past and current passenger cars and light trucks. It is intended for readers with a technical background. It does not include information about aftermarket devices or future antilock brake systems. Information in this document reflects that which was available to the committee at the time of publication.
2014-04-01
WIP Standard
J2204
This SAE Standard applies to the usage of tires of the same nominal size and tread type, but with different outside diameter for articulated front-end loaders. Articulated four-wheel-drive front-end loader performance and component life can be affected by excessive differences in the tire outside circumference and/or diameter. The purpose is to provide specific guidelines for the usage of tires with different outside circumference and/or diameter on articulated front-end loaders.
2014-03-07
WIP Standard
J1047
This SAE Recommended Practice covers the tubing intended primarily for use as hydraulic brake lines on motor vehicles. It covers materials, manufacturing processes, and general properties required to meet the wide range of service encountered in automotive applications. To meet this need, it must be formed, assembled, handled, and installed in accordance with sound engineering and manufacturing practices. This specification covers only the basic tubing and does not include attachments such as protective armor or end fittings. This document is not intended to be used for quality control purposes. Design guidelines are shown in Appendix A.
2014-03-05
WIP Standard
J1729
This SAE Recommended Practice provides a test method and instructions for measuring performance of parking brakes on air- or hydraulic-braked vehicles equipped with in-wheel or drive-line parking brakes. This procedure applies to truck tractors, trailers, trucks and buses.
HISTORICAL
2014-02-27
Standard
J1939DA_201402
The J1939 Digital Annex The J1939 Digital Annex, introduced in August 2013, offers key J1939 technical data in an Electronic Spreadsheet that can be easily searched, sorted, and adapted to other formats. J1939DA contains all of the SPNs (parameters), PGNs (messages), and other J1939 data previously published in the SAE J1939 top level document. J1939DA also contains all of the SLOTs, Manufacturer ID Codes, NAME Functions, and Preferred Addresses previously published in the SAE J1939 top level and the J1939-71 document. J1939DA contains the complete technical details for all of the SPNs and PGNs previously published in the SAE J1939-71 document. For all other SPNs and PGNs which are published in a document other than SAE J1939-71, J1939DA lists only basic details along with a reference to the document that contains the complete technical details. J1939DA replaces, and expands upon, the 1939 Companion Spreadsheet (CS1939), which was last published through November 2012.
CURRENT
2014-02-21
Standard
J2191_201402
This SAE document defines a recommended practice for implementing circuit identification for electrical power and signal distribution systems of the Class 8 trucks and tractors. This document provides a description of a supplemental circuit identifier that shall be utilized in conjunction with the original equipment manufacturer’s primary circuit identification as used in wire harnesses but does not include electrical or electronic devices which have pigtails. The supplemental circuit identifier is cross-referenced to a specified subsystem of the power and signal distribution system identified in Section 5.
CURRENT
2014-02-17
Standard
J2812_201402
This SAE Recommended Practice describes an evaluation procedure for validating tire models for use in road load simulations and assesses the relevant dynamic behavior of tires. The laboratory test utilized is a “cleat” test, where a rolling tire on a drum encounters a cleat and the resulting dynamic forces and moments are measured. This test is described in SAE J2730, “Dynamic Cleat Test with Perpendicular and Inclined Cleats”. The test is commonly used to identify tire model parameters. In this recommended practice, requirements for the measurement of the tire’s response are described along with data processing techniques and calculations used to quantitatively compare the tire model’s calculated response to the tire’s response measured on test. This recommended practice addresses both the tire model structure and its parameters.
CURRENT
2014-02-05
Standard
J1911_201402
This SAE Recommended Practice provides instructions and test procedures for air braked vehicles including but not limited to trucks, truck-tractors, trailers, dollies, and buses used on highways but does not include off-highway vehicles.
CURRENT
2014-02-03
Standard
J1842_201402
This SAE Recommended Practice is intended for hubs and spoke wheels used on Class 6, 7, and 8 truck/truck-tractor non-powered front axles, powered and non-powered rear axles and trailer axles, for which bearing setting is manually adjusted. Assemblies using spacers to control bearing preload and endplay may differ in geometry and bearing componentry.
CURRENT
2014-01-08
Standard
J738_201401
This standard is for cutting edge sections typically used in earth-moving machinery defined in SAE J1116 and ISO 6165: Scrapers as defined in ISO 7133. Dozers as described in ISO 6747. Loaders as described in ISO 7131. Graders as described in ISO 7134. Hole spacing is defined ISO 7129. Hole conformation is defined in SAE J740.
CURRENT
2014-01-03
Standard
J1835_201401
This SAE Recommended Practice establishes the mounting hardware to be used with demountable rims, wheels for demountable rims, rim spacers designed for 28 degrees bevel mounting systems, and intended for use on commercial vehicles. The dimensions given are those necessary to maintain serviceability and interchangeability of mounting hardware. This document is divided into two sections. Section 1 establishes the practice for new designs for mounting hardware. Section 2 records information on current mounting hardware. Special and less common applications are not covered in this document.
HISTORICAL
2013-12-20
Standard
J2975_201312
This procedure describes a method for generating, preparing and analyzing samples of new and unused brake friction materials for their chemical constituents.
CURRENT
2013-12-20
Standard
J108_201312
This SAE Recommended Practice establishes a uniform procedure for the level road test of the brake systems of all classes of motorcycles intended for highway use.
CURRENT
2013-12-17
Standard
J2899_201312
This SAE Recommended Practice applies to S-CAM, Wedge, and Disc air brake actuators where the stroke can be measured without disassembly from the brake.
CURRENT
2013-12-17
Standard
J1472_201312
This SAE Standard specifies brake system performance and test criteria to enable uniform evaluation of the braking capability of self-propelled, ride-on vibratory steel wheel, static steel wheel, and rubber-tire roller compactors with maximum level surface machine speeds of 25 km/h or less. Service, secondary, and parking brakes are included. Machines with maximum level surface machine speeds greater than 25 km/h shall conform to the requirements of SAE J/ISO 3450.
CURRENT
2013-12-16
Standard
ARP6152
This SAE Aerospace Recommended Practice (ARP) defines a procedure for demonstrating service overload capability for new, main and nose landing gear, radial or bias tires fitted on multiple wheel landing gear of Part 25 certified aircraft.
CURRENT
2013-12-16
Standard
AIR4777B
This SAE Aerospace Information Report (AIR) identifies current nondestructive inspection (NDI) methods used to ensure product integrity and maximize "in service" life of the major structural components of aircraft wheel and brake assemblies.
2013-12-04
WIP Standard
AS6289
The scope of the test method is to provide stakeholders including fluid manufacturers, brake manufacturers, aircraft constructors, aircraft operators and airworthiness authorities with a relative assessment of the effect of deicing chemicals on carbon oxidation. This test is designed to assess the relative effects of runway deicing chemicals by measuring mass change of contaminated and bare carbon samples tested under the same conditions.
CURRENT
2013-12-04
Standard
J10_201312
This SAE Standard applies to all new production air brake and air accessory reservoirs used in automotive vehicles and off-road machines. This document defines an “air reservoir” as a reservoir having single or multiple compartments that is used for storage of compressed air. This document does not apply to accumulators or reservoirs for storage of gases other than compressed air.
HISTORICAL
2013-11-19
Standard
J1939DA_201311
The J1939 Digital Annex The J1939 Digital Annex, introduced in August 2013, offers key J1939 technical data in an Electronic Spreadsheet that can be easily searched, sorted, and adapted to other formats. J1939DA contains all of the SPNs (parameters), PGNs (messages), and other J1939 data previously published in the SAE J1939 top level document. J1939DA also contains all of the SLOTs, Manufacturer ID Codes, NAME Functions, and Preferred Addresses previously published in the SAE J1939 top level and the J1939-71 document. J1939DA contains the complete technical details for all of the SPNs and PGNs previously published in the SAE J1939-71 document. For all other SPNs and PGNs which are published in a document other than SAE J1939-71, J1939DA lists only basic details along with a reference to the document that contains the complete technical details. J1939DA replaces, and expands upon, the 1939 Companion Spreadsheet (CS1939), which was last published through November 2012.
CURRENT
2013-11-01
Standard
ARP1493C
This document covers military aircraft wheel and hydraulically actuated brake equipment.
CURRENT
2013-11-01
Standard
AS8584B
This SAE Aerospace Standard (AS) defines the requirements for brake systems used on military aircraft equipped with wheel-type landing gears.
CURRENT
2013-11-01
Standard
AS707C
The focus of this SAE Aerospace Standard (AS) is the integration of thermally actuated pressure release devices, hereafter referred to as fuse plugs, with the wheel and brake assembly. It does not address the manufacturing, quality or acceptance test requirements pertaining to the production of these fuse plugs. It establishes minimum design, installation, qualification, and operational requirements for fuse plugs which are used only in tubeless tire type aircraft braked wheels. Fuse plugs are designed to completely release the contained inflation pressure from a tubeless tire and wheel assembly when brake generated heat causes the tire or wheel to exceed a safe temperature level. The objective is to prevent tire or wheel rupture due to brake generated heat that could cause an unsafe condition for personnel or the aircraft. (Reference: U.S. Department of Transportation FAA Advisory Circular No. 23-17C; Title 14, Code of Federal Regulations (14 CFR) Part 25.735 (j); U.S.
Viewing 181 to 210 of 1543