Criteria

Text:
Topic:
Content:
Display:

Results

Viewing 1561 to 1590 of 1600
HISTORICAL
1967-11-01
Standard
J318_196711
This SAE Recommended Practice is intended to provide a design, critical dimensions, performance requirements, and identification for gladhand-type air line couplers used to connect the brake systems of trucks, truck-tractors, and trailers when these vehicles are joined to operate as a combination unit. The purpose is to provide a coupler half for the service (control) and emergency (supply) brake lines on one vehicle that will be identified and compatible with the coupler halves on the service (control) and emergency (supply) brake lines of another vehicle.
HISTORICAL
1967-09-01
Standard
J1703_196709
This SAE Standard covers motor vehicle brake fluids of the nonpetroleum type for use in the braking system of any motor vehicle such as a passenger car, truck, bus, or trailer. These fluids are not intended for use under arctic conditions. These fluids are designed for use in braking systems fitted with rubber cups and seals made from styrene-butadiene rubber (SBR), or a terpolymer of ethylene, propylene, and a diene (EPDM).
HISTORICAL
1967-08-01
Standard
J901A_196708
The following definitions and illustrations are intended to establish common nomenclature and terminology for universal joints and driveshafts used in various driveline applications. In addition, useful guidelines are included for the application of universal joints and driveshafts. For more specific details, see Universal Joint and Driveshaft Design Manual, AE-7.
HISTORICAL
1967-07-01
Standard
J992_196707
This SAE Recommended Practice presents performance requirements for the brake systems of motor vehicles intended for roadway use and falling into the following classifications: Light trucks and buses: 6001-10 000 lb (2700-4500 kg) gvw; Truck and bus: Over 10 000 lb (4500 kg) gvw; combination of vehicles towing vehicles over 10 000 lb (4500 kg) gvw. Acceptable performance requirements are based on data obtained from applicable sections of SAE J786a (March, 1978). The purpose of this recommended practice is to establish the minimum brake system performance requirements with regard to: 3.1 Stopping ability--of cold brakes, as affected by vehicle speed. 3.2 Stopping ability--of hot brakes, as affected by vehicle speed and duty cycle. 3.3 Pedal force (air pressure) requirements--maximum allowable. 3.4 Brake stability. 3.5 stopping ability and recovery of wet brakes. 3.6 Stopping ability of emergency brake system. 3.7 Brake effectiveness distribution for vehicles in combination.
HISTORICAL
1967-04-01
Standard
J661A_196704
The purpose of this SAE Recommended Practice is to establish a uniform laboratory procedure for securing and reporting the friction and wear characteristics of brake linings. The performance data obtained can be used for in-plant quality control by brake lining manufacturers and for the quality assessment of incoming shipments by the purchasers of brake linings.
1967-03-01
Standard
J40D_196703
1967-01-01
Standard
J40C_196701
HISTORICAL
1966-12-01
Standard
J918B_196612
This SAE Standard provides minimum performance requirements and accompanying uniform laboratory test procedures for evaluating certain essential characteristics of new tires and newly retreaded tires intended for use on passenger cars. (The requirements published in this SAE Standard pertain to tire sizes currently used on American passenger cars and popular sizes used on imported passenger cars. For related information on tire sizes not listed, contact SAE Automotive Headquarters, 18121 East Eight Mile Road, East Detroit, Michigan 48021.)
HISTORICAL
1966-12-01
Standard
ARP813
This Aerospace Recommended Practice (ARP) recommends the maintainability features which should be considered in the design of aircraft wheels and brakes. The effect on other factors, such as, cost, weight, reliability, and compatibility with other systems should be weighed before the incorporation of any of these maintainability features into the design.
HISTORICAL
1966-09-01
Standard
J971_196609
The code provides test procedures and methods of calculating a brake rating from the data obtained for brakes used in highway commercial vehicles over 4.5 T (10 000 lbs) GVWR air and hydraulic. Some general correlation may be expected between brake ratings established by this means and those obtained from vehicle tests such as outlined in SAE J880. The brake rating power, kW (hp) calculated by conduct of this code is an arbitrary index of performance of the brake and drum when tested by this procedure and may be appreciably different from the values obtained by other techniques.
HISTORICAL
1966-09-01
Standard
J866A_196609
This SAE Recommended Practice is intended to provide a uniform means of identification which may be used to classify the friction coefficient of brake linings, based on data obtained from tests conducted in accordance with SAE J661 Brake Lining Quality Test Procedure and SAE J2975 Measurement of Copper and other elements in Brake Friction Materials. NOTE: It is emphasized that this document does not establish friction requirements for brake linings, nor does it designate significant characteristics of brake linings which must be considered in overall brake performance. Due to other factors that include brake system design and operating environment, the friction codes obtained from this document cannot reliably be used to predict brake system performance.
HISTORICAL
1966-08-01
Standard
J796A_196608
HISTORICAL
1966-08-01
Standard
J966_196608
This SAE Recommended Practice provides a test procedure for determining passenger car tire revolutions per mile. It is intended to supplement SAE J678.
HISTORICAL
1966-06-20
Standard
AIR764A
This technical report documents three surveys to determine realistic vibration requirements for skid control systems specifications and obtain updated vibration information for locations in aircraft where skid control system components are mounted.
HISTORICAL
1966-01-01
Standard
J918A_196601
This SAE Standard provides minimum performance requirements and accompanying uniform laboratory test procedures for evaluating certain essential characteristics of new tires and newly retreaded tires intended for use on passenger cars. (The requirements published in this SAE Standard pertain to tire sizes currently used on American passenger cars and popular sizes used on imported passenger cars. For related information on tire sizes not listed, contact SAE Automotive Headquarters, 18121 East Eight Mile Road, East Detroit, Michigan 48021.)
HISTORICAL
1965-12-01
Standard
J944_196512
1. SCOPE Evaluation of the energy absorbing properties of the steering wheel assembly of a motor vehicle, or of the relative merit of altemative designs of such assemblies, is a complex problem involving human tolerance, vehicle and occupant dynamics during an accident, and frequency and severity of injuries to various body areas. T\'lO fundamental approaches are being used currently for steering wheel assembly evaluations: laboratory impact tests of varying degrees of complexity, and simulated collision tests. This SAE Recommended Practice describes a simplified laboratory procedure for evaluating the characteristics of steering wheel assemblies under simulated driver impact conditions. Basically, the test procedure employs a torso shaped body block which is impacted against the steering wheel assembly and the transmitted load -time history is measured.
HISTORICAL
1965-09-01
Standard
J843A_196509
This SAE Recommended Practice establishes a uniform procedure for the level road test of the brake systems of new light-duty trucks and new multipurpose passenger vehicles up to and including 2700 kg (6000 lb) GVW and all classes of new passenger cars. The purpose of the test code is to establish brake system capabilities with regard to: a. Deceleration versus input, as affected by vehicle speed, brake temperature, and usage; b. brake system integrity; c. Stopping ability during emergency or inoperative power assist conditions; d. Water recovery characteristics.
1965-07-01
Standard
J40B_196507
HISTORICAL
1965-06-01
Standard
J918_196506
This SAE Standard provides minimum performance requirements and accompanying uniform laboratory test procedures for evaluating certain essential characteristics of new tires and newly retreaded tires intended for use on passenger cars. (The requirements published in this SAE Standard pertain to tire sizes currently used on American passenger cars and popular sizes used on imported passenger cars. For related information on tire sizes not listed, contact SAE Automotive Headquarters, 18121 East Eight Mile Road, East Detroit, Michigan 48021.)
HISTORICAL
1965-02-01
Standard
J75_196502
Motor vehicle brake fluid must conform to the requirements of SAE J1703 or J1704, not only when manufactured, but also after extended storage in any commercial packaging container. The purpose of this SAE Information Report is to generate an awareness of the major problems involved in the storage of brake fluids and, to some extent, provide means of circumventing them. It is also the purpose of this document to relate to experience and to test data accumulated and to list certain conclusions which should aid in the proper selection of containers for brake fluid.
HISTORICAL
1965-01-20
Standard
AS586
This SAE Aerospace Standard (AS) sets forth the minimum quality required for aircraft wheel and brake castings. Its use will establish minimum acceptable requirements for internal structure and surface conditions and is predicated on the use of a casting factor for the ultimate load of more than 1.51 through 2.00. When casting factors of 1.25 through 1.50 are used, visual, penetrant, and radiographic or other approved equivalent nondestructive inspection methods shall all be required on each production casting. Where specific parts, or areas of parts, require a quality level exceeding that described by this document, the requirements shall be established by negotiation between the purchaser and vendor.
HISTORICAL
1965-01-01
Standard
AIR811
This SAE Aerospace Information Report (AIR) has been prepared to assist those who are converned with the removal, inspection, and disposition of magnesium and aluminum wheels which may have been subjected to excessive temperatures.
HISTORICAL
1964-09-01
Standard
J447A_196409
This SAE Information Report provides automotive engineers with the basic principles of corrosion, design guidelines to minimize corrosion, and a review of the various materials, treatments, and processes available to inhibit corrosion of both decorative and functional body and chassis components.
HISTORICAL
1964-03-01
Standard
J866_196403
This SAE Recommended Practice is intended to provide a uniform means of identification which may be used to classify the friction coefficient of brake linings, based on data obtained from tests conducted in accordance with SAE J661 Brake Lining Quality Test Procedure and SAE J2975 Measurement of Copper and other elements in Brake Friction Materials. NOTE: It is emphasized that this document does not establish friction requirements for brake linings, nor does it designate significant characteristics of brake linings which must be considered in overall brake performance. Due to other factors that include brake system design and operating environment, the friction codes obtained from this document cannot reliably be used to predict brake system performance.
HISTORICAL
1963-11-01
Standard
AS666
This AS applies to the cavity design and the selection of O-rings for tubeless tire wheels.
HISTORICAL
1963-11-01
Standard
AIR764
This technical report documents three surveys to determine realistic vibration requirements for skid control systems specifications and obtain updated vibration information for locations in aircraft where skid control system components are mounted.
HISTORICAL
1963-11-01
Standard
J880_196311
This code is intended for commercial vehicles over 4500 kg (10 000 lb) with brake systems having typical service pressure ranges 0 to 14.1 mPa (0 to 2050 psi) hydraulic or 0 to 830 kPa (0 to 130 psi) air and is not directly applicable to vehicles with other systems. Air over hydraulic systems are to be tested as air systems.
Viewing 1561 to 1590 of 1600