Criteria

Text:
Content:
Display:

Results

Viewing 1 to 30 of 878
CURRENT
2017-03-13
Standard
J2995_201703
This recommended practice will specify a standard duty cycle and set of conditions for component-level durability testing. The "duty cycle" refers to a set of loading conditions (e.g. torque or pressure and cycling count), and the 'test conditions" refers to environmental conditions such as temperature, humidity, and part conditioning from prior exposure (e.g. heat aging).
2017-02-13
WIP Standard
J2789
This Recommended Practice is useful to determine the inertia value (wheel load and tire radius) using three basic methods (fixed brake work split, dynamic weight transfer, and axle rating) to determine the wheel load and two methods to determine the tire radius (SLR and rolling radius). The inertia values are required to determine the amount of energy and brake work imposed on the brake during testing. The inertia level (mechanical or simulated) is required also to calculate deceleration levels from a given torque value or the torque level for a given deceleration value or set-point. This procedure is applicable to all passenger cars and light trucks up to 4,540kg of GVWR.
2017-02-10
WIP Standard
J2899
This SAE Recommended Practice applies to S-CAM, Wedge, and Disc air brake actuators where the stroke can be measured without disassembly from the brake.
CURRENT
2017-02-09
Standard
J1469_201702
This SAE Recommended Practice provides procedures and methods for testing service, spring applied parking, and combination brake actuators with respect to durability, function, and environmental performance. A minimum of six test units designated A, B, C, D, E, and F are to be used to perform all tests per 1.1 and 1.2.
2017-02-09
WIP Standard
J2247
This SAE Recommended Practice identifies the minimum truck tractor electrical power output of the stop lamp and ABS (antilock brake system) circuits measured at the primary SAE J560 tractor trailer interface connector(s).
CURRENT
2017-02-02
Standard
J2581_201702
This SAE Information report defines the thermal transport properties important in the assessment of heat management capability of brake lining, shoe, disc and drum materials. The report discusses thermal diffusivity, specific heat capacity, thermal conductivity and thermal expansion. Measurement techniques for the appropriate ASTM standards are identified. The thermal transport properties discussed are material sample properties, not the properties of entire components such as pad assemblies.
CURRENT
2017-02-02
Standard
J380_201702
Specific gravity is a nondestructive test used as a quality control check of the consistency of formulation and processing of brake lining. The specific gravity and the range of specific gravity are peculiar to each formulation and, therefore, the acceptable values or range must be established for each formulation by the manufacturer. Specific gravity alone shows nothing about a materials in use performance. The specific gravity of sintered metal powder friction materials, particularly those which have steel backing members, is usually determined somewhat differently. Reference ASTM B 376. Purpose To establish a uniform procedure for determining the specific gravity of brake friction material.
CURRENT
2017-02-02
Standard
J379_201702
Hardness measurements are used as a quality control check of the consistency of formulation and processing of brake linings. Gogan hardness is nondestructive (the penetrator causes shallow surface deformation.). Gogan hardness method alone does not show anything about a lining’s ability to develop friction or to resist fade when used as a friction element in brakes. The hardness and the range of hardness are peculiar to each formulation, thickness, and contour; therefore, the acceptable values and ranges must be established for each formulation and part configuration by the manufacturer.
CURRENT
2017-01-12
Standard
ARP5429A
This SAE Aerospace Recommended Practice (ARP) applies to fatigue testing of landing gear and landing gear components.
CURRENT
2017-01-05
Standard
J1626/2_201701
This Recommended Practice provides a road test procedure for trucks and buses, to evaluate their compliance with Federal Motor Vehicle Safety Standard (FMVSS) 121; Air Brake Systems. Units of measure are English in lieu of metric to be consistent with FMVSS 121.
2016-12-17
WIP Standard
J2394
This SAE standard establishes the minimum construction and performance requirements for seven conductor 1/8 2/10 4/12 cable for use on trucks, trailers and converter dollies. Where appropriate, the standard refers to two types of cables, (Type F and S, described later in the standard), due to the variation in the performance demands of cables used in flexing and stationary applications. While the document’s title refers to ABS Power to differentiate the document from the SAE J1067 standard that it supersedes, the scope applies to both the primary green cable for powering ABS and lighting and the yellow auxiliary cable of the same construction.
2016-11-30
WIP Standard
J1706
This SAE Recommended Practice is intended to provide basic recommended practices for aid in the development and use of safe and efficient practices for all operations involving the production, handling, and dispensing of SAE J1703 Motor Vehicle Brake Fluids and SAE J1704 Borate Ester Based Brake Fluids.
2016-11-16
WIP Standard
J2707
This SAE Recommended Practice specifies a dynamometer test procedure to be used for the measurement of automotive service brake linings and disc brake pads wear. Special motor vehicles and motorcycles are excluded from the application. Trailers with nominal Gross Combination Weight Rating exceeding 40 tons are also excluded from this Recommended Practice.
CURRENT
2016-11-10
Standard
J2318_201611
This procedure provides test performance requirements for service, spring applied parking, and double diaphragm combination air brake actuators with respect to durability, function, and environmental performance when tested in accordance to SAE J1469.
2016-11-03
WIP Standard
AIR6805
This document will outline existing best practices in the instrumentation of landing gears for in-service operation (including flight test, operational loads monitoring, etc.).
CURRENT
2016-11-01
Standard
J2580_201611
This Recommended Practice covers air braked trucks, truck-tractors, trailers and buses. It enumerates the identification and installation of the air brake components not covered in other SAE recommended practices and standards.
CURRENT
2016-10-25
Standard
J2690_201610
This SAE Recommended Practice establishes uniform test procedures for friction based parking brake components used in conjunction with hydraulic service braked vehicles with a gross vehicle weight rating greater than 4500 kg (10 000 lb). The components covered in this document are the primary actuation and the foundation park brake. Various peripheral devices such as application dashboard switches or indicators are not included.
CURRENT
2016-10-21
Standard
ARP1619B
This SAE Aerospace Recommended Practice (ARP) defines recommended planning and substantiation procedures and associated reviewing and approval processes to confirm that proposed changes do not compromise the demonstrated safety of the originally certified aircraft, and performance and aircraft compatibility are appropriately addressed in aircraft documentation. Successful demonstration also requires that failure modes be identified and mitigation provided for each. These procedures apply to modifications made by the original component or assembly supplier as well as approval of an alternate supplier.
2016-10-05
WIP Standard
J2784
This Recommended Practice is derived from the Federal Motor Vehicle Safety Standard 135 vehicle test protocol as a single-ended inertia-dynamometer test procedure. It measures brake output, friction material effectiveness, and corner performance in a controlled and repeatable environment. The test procedure also includes optional sections for parking brake output performance for rear brakes. It is applicable to brake corners from vehicles covered by the FMVSS 135 when using the appropriate brake hardware and test parameters. This procedure is applicable to all passenger cars and light trucks up to 3500 kg of GVWR.
2016-10-05
WIP Standard
J1452
This SAE Recommended Practice establishes methods to determine grade parking performance with respect to: a. Ability of the parking brake system to lock the braked wheels. b. The trailer holding or sliding on the grade, fully loaded or unloaded. c. Applied manual effort. d. Unburnished or burnished brake lining friction conditions. e. Down and up grade directions. Purpose This document establishes a uniform procedure for determining the parking performance on a grade of any new trailer with manufacturer's maximum weight rating of more than 4540 kg (10 000 lb) intended for roadway use.
2016-10-05
WIP Standard
J293
This SAE Recommended Practice establishes minimum performance requirements for trucks, buses, truck-tractors, full trailers, and semitrailers with gross vehicle weight ratings greater than 4540 kg (10 000 lb) with regard to: a. Vehicle classification b. Vehicle load c. Percent grade d. Application force
2016-10-04
WIP Standard
J2725
This SAE Standard specifies a method for testing and measuring elastic constants in friction materials by precise ultrasonic velocity measurements.
2016-09-16
WIP Standard
J2806
Subject document is specifically intended for service brakes and service brakes when used for parking and/or emergency brakes (only) that are commonly used for automotive-type, ground wheeled vehicles exceeding 4536 kg (10 000 US lb) Gross Vehicle Weight Rating (GVWR). Subject specification provides the off-vehicle procedures, methods, and processes used to objectively determine suitability of tactical and combat ground wheeled vehicle brake systems and selected secondary-item brake components (a.k.a. aftermarket or spare parts), including brake “block” for commercial applications only, specifically identified within subject document. Subject specification is primarily based on known industry and military test standards utilizing brake inertia dynamometers. Targeted vehicles and components include, but may not be limited to the following: a.
CURRENT
2016-09-14
Standard
AS1145C
This specification covers minimum requirements for brake temperature monitoring equipment whenever used on any type and model of civil aircraft. It shall be the responsibility of the purchaser to determine the compatibility of these requirements with the application aircraft and to specify requirements in excess of these minimums as necessary.
2016-09-14
WIP Standard
J257
The minimum performance values in this SAE Recommended Practice are applicable to vehicles with brake systems having typical service pressure ranges 0 to 16.6 MPa (0 to 2400 psi) hydraulic or 0 to 945 kPa (0 to 135 psi) air only. SAE J880 not only provides for determining maximum brake rating power capability, but also permits verification of any desired or arbitrary level such as the requirement established herein. The determining criteria for deciding brake rating power capability are: a. Cold brake stopping ability. b. Fade as a result of brake power absorption. c. Hot brake stopping ability following brake power absorption. d. Brake system stability following brake power absorption. e. Functional and structural integrity of brake system following test.
2016-09-14
WIP Standard
J75
Motor vehicle brake fluid must conform to the requirements of SAE J1703 or J1704, not only when manufactured, but also after extended storage in any commercial packaging container. The purpose of this SAE Information Report is to generate an awareness of the major problems involved in the storage of brake fluids and, to some extent, provide means of circumventing them. It is also the purpose of this document to relate to experience and to test data accumulated and to list certain conclusions which should aid in the proper selection of containers for brake fluid.
CURRENT
2016-09-13
Standard
J1707_201609
This SAE Recommended Practice provides basic recommendations for dispensing and handling of SAE J1703 and SAE J1704 Brake Fluids by Service Maintenance Personnel to assure their safe and effective performance when installed in or added to motor vehicle hydraulic brake actuating systems. This document is concerned only with brake fluid and those system parts in contact with it. It describes general maintenance procedures that constitute good practice and that should be employed to help assure a properly functioning brake system. Recommendations that promote safety are emphasized. Specific step-by-step service instructions for brake maintenance on individual makes or models are neither intended nor implied. For these, one should consult the vehicle manufacturer’s service brake maintenance procedures for the particular vehicle. Vehicle manufacturer’s recommendations should always be followed.
2016-09-08
WIP Standard
J2742
This SAE standard establishes the minimum construction and performance requirements for a combination cable consisting of 11 conductors and 4 twisted pairs for use on trucks, trailers, and dollies in conjunction with SAEJ2691. (15 pole connectors.) The cable includes both power and unjacketed SAE J1939-15 paired signal circuits along with dual ground wires to accommodate grounding requirements within the constraints of the SAE J2691 terminal capacity.
2016-08-17
WIP Standard
J1401

This SAE Standard specifies the performance tests and requirements for hydraulic brake hose assemblies used in the hydraulic braking system of a road vehicle. It also specifies the methods used for identification of the hose manufacturer.

This document applies to brake hose assemblies made of a hose fabricated from yarn and natural or synthetic elastomers and assembled with metal end fittings for use with nonpetroleum-base brake fluids as specified in SAE J1703, SAE J1704 and SAE J1705.

The nominal internal diameter of the brake hose shall fall within one of the following values:

    a. less than 4 mm (1/8 in or less)
    b. 4 to 5 mm (3/16 in)

CURRENT
2016-08-16
Standard
J1615_201608
Male pipe threads, including male dryseal pipe threads, when made into assemblies or installed into ports, will generally leak if not covered with a sealant. This SAE Recommended Practice is intended as a guide to assist designers and/or users in the selection and application of various types of thread sealants. The designers and users must make a systematic review of each type and application and then select the sealant to fulfill the requirements of the application. The following are general guidelines and are not necessarily a complete list.
Viewing 1 to 30 of 878