Criteria

Text:
Content:
Display:

Results

Viewing 181 to 210 of 1688
2015-04-28
WIP Standard
AIR6892
This SAE Aerospace Information Report (AIR) is applicable to rotorcraft structural health monitoring (SHM) applications, both commercial and military, where end users are seeking guidance on the definition, development, integration, qualification, and certification of SHM technologies to achieve enhanced safety and reduced maintenance burden based on the lessons learned from existing Health and Usage Monitoring Systems (HUMS). While guidance on SHM business case analysis would be useful to the community, such guidance is beyond the scope of this AIR. For the purpose of this document, SHM is defined as “the process of acquiring and analyzing data from on-board sensors to evaluate the health of a structure.” The suite of on-board sensors could include any presently installed aircraft sensors as well as new sensors to be defined in the future. Interrogation of the sensors could be done onboard during flight or using ground support equipment.
CURRENT
2015-04-21
Standard
J1037_201504
This SAE Standard covers nonreinforced, extruded, flexible tubing intended primarily for use as fluid lines for automotive windshield washer systems which conform to the requirements of SAE J942.
2015-04-20
WIP Standard
J1246
The SAE Recommended Practice is intended for use in measuring the radius of curvature (ROC) of spherical convex mirrors.
CURRENT
2015-03-24
Standard
J1889_201503
This SAE Recommended Practice applies to functions of motor vehicle signaling and marking lighting devices which use light emitting diodes (L.E.D.’s) as light sources. This report provides test methods, requirements, and guidelines applicable to the special characteristics of L.E.D. lighting devices. This Recommended Practice is in addition to those required for devices designed with incandescent light sources. This report is intended to be a guide to standard practice and is subject to change to reflect additional experience and technical advances.
CURRENT
2015-03-19
Standard
J2635_201503
This test procedure defines a laboratory procedure for generating and evaluating filiform corrosion on painted aluminum wheels and painted aluminum wheel trim. While this test was developed specifically for the testing of painted aluminum wheels and wheel trim it may be applicable to other components. The application owner will need to assess if this test generates filiform similar to that found in the relevant usage to ensure it will provide accurate data for the application.
CURRENT
2015-03-13
Standard
J374_201503
This SAE Recommended Practice establishes a uniform laboratory test method to evaluate the strength characteristics of roof systems. The test procedure is intended to provide reliable and repeatable results and to permit numerical comparisons. A test is conducted in which the vehicle roof system is loaded under controlled laboratory conditions. Structural strength measurements are obtained under load application angles chosen to concentrate forces on the forward portions of the roof panel and roof supporting structure.
CURRENT
2015-03-13
Standard
J972_201503
Collision tests are conducted on automotive vehicles to obtain information of value in evaluation of structural integrity and in reducing the risk of occupant injuries. The deformation resulting from a moving rigid barrier impact is more severe at a given speed than that produced by using an actual vehicle, but is more readily reproducible than that occurring during vehicle to vehicle impacts. The purpose of this SAE Recommended Practice is to establish sufficient standardization of such moving barriers and moving barrier collision methods so that results of tests conducted at different facilities may be compared.
CURRENT
2015-02-26
Standard
J1623_201502
This SAE Recommended Practice provides test procedures and performance requirements for off-highway vehicle headlamps.
CURRENT
2015-02-24
Standard
AS92C
CURRENT
2015-02-20
Standard
J1671_201502
This recommended practice contains dimensions and tolerances for outboard mounted brake drums and disc wheel hubs in the interface areas. This recommended practice is intended for outboard mounted brake drums and disc wheel hubs commonly used on class 7 and 8 commercial vehicles. Included are SAE J694 mounting systems II, III, IV, XIV, and X. Special and less common applications are not covered.
CURRENT
2015-02-17
Standard
J567_201502
This SAE Standard references the performance and functional requirements of the International Electrotechnical Commission (IEC) and its U.S. member, the American National Standards Institute (ANSI). By referring to IEC/ANSI and its standards concerning light source (bulb) sockets, light source (lamp) holders, and gages, this document recognizes the need for harmonized standards world-wide for what are typically commodity items. Additional requirements are noted.
2015-02-06
WIP Standard
J3086
This SAE Automotive Lighting Materials Recommended Practice incorporates several test methods in order to provide performance requirements facilitating a more accurate assessment of headlamp lens systems (lens substrate plus coating(s) if applicable) durability versus the established practice.
2015-01-16
WIP Standard
J845
This document provides design guidelines, test procedure references, and performance requirements for omnidirectional and selective coverage optical warning devices used on authorized emergency, maintenance and service vehicles. It is intended to apply to, but is not limited to, surface land vehicles.
HISTORICAL
2015-01-15
Standard
J1647_201501
This SAE Recommended Practice provides test methods and requirements to evaluate the suitability of plastic optical materials for possible use in discharge forward lighting (DFL) devices in motor vehicles. These materials are typically used for lenses and reflectors. Separate testing is required for each combination of material, industrial coating, DFL light source, and device focal length. The tests are intended to determine physical and optical characteristics of the materials and coatings. Performance expectations of finished assemblies, including plastic components, are to be based on tests for lighting devices, as specified in SAE Standards and Recommended Practices for motor vehicle lighting equipment. Optical components exposed to weathering should also be subject to SAE J576.
2014-12-09
WIP Standard
AIR4543/2
This SAE Aerospace Information Report (AIR) contains Lessons Learned from aerospace actuation, control and fluid power systems technologies. The lessons were prepared by engineers from the aerospace industry and government services as part of the work of SAE Committee A-6, Aerospace Actuation, Control and Fluid Power Systems.
2014-12-03
WIP Standard
J1453/3
The three parts of SAE J1453 cover material, dimensional, and performance requirements of steel O-ring face seal (ORFS) connectors for tubing and the O-ring face seal interface and nut portion of hose stem assemblies for nominal tube diameters of 6 mm through 50 mm. SAE J1453-3 covers the requirements for O-ring face seal connectors to inch stud ends along with the associated adapters, bulkhead and union connectors. Inch hex dimensions of parts will be moved from the main document to an informative annex after 2013.
CURRENT
2014-12-02
Standard
J2139_201412
This SAE Recommended Practice provides standardized laboratory tests, test methods, and performance requirements applicable to signal and marking devices used on vehicles 2032 mm or more in overall width.
HISTORICAL
2014-12-02
Standard
J2087_201412
This SAE Standard provides test procedures, requirements, and guidelines for a daytime running light (DRL) function.
CURRENT
2014-12-01
Standard
AIR4243A
This document discusses the work done by the U.S. Army Corps of Engineers and the Waterways Experiment Station (WES) in support of SAE A-5 Committee activity on Aerospace Landing Gear Systems. It is an example of how seemingly unrelated disciplines can be combined effectively for the eventual benefit of the overall aircraft system, where that system includes the total airfield environment in which the aircraft must operate. In summary, this AIR documents the history of aircraft flotation analysis as it involves WES and the SAE.
CURRENT
2014-12-01
Standard
AS5452B
This SAE Aerospace Standard (AS) will specify what type night vision goggles are required, minimum requirements for compatible crew station lighting, aircraft exterior lighting such as anticollision lights and position/navigation lights that are "NVG compatible." Also, this document is intended to set standards for NVG utilization for aircraft so that special use aircraft such as the Coast Guard, Border Patrol, Air Rescue, Police Department, Medivacs, etc., will be better equipped to chase drug smugglers and catch illegal immigrants, rescue people in distress, reduce high-speed chases through city streets by police, etc. Test programs and pilot operator programs are required. For those people designing or modifying civil aircraft to be NVG compatible, the documents listed in 2.1.3 are essential.
CURRENT
2014-11-18
Standard
J1214_201411
The purpose of this SAE Recommended Practice is set guidelines for tire to wheel house and body clearances on recreational vehicles.
CURRENT
2014-11-13
Standard
AS33515D
Scope unavailable.
CURRENT
2014-11-11
Standard
ARP1070D
This document outlines the development process and makes recommendations for total antiskid/aircraft systems compatibility. These recommendations encompass all aircraft systems that may affect antiskid brake control. It focuses on recommended practices specific to antiskid and its integration with the aircraft as opposed to more generic practices recommended for all aircraft systems and components. It defers to the documents listed in Section 2, for generic aerospace best practices and requirements.
2014-11-05
WIP Standard
ARP6887
The ARP shall cover the objectives and activities of Verification & Vallidation Processes required to assure high quality and/or criticality level of an IVHM Systems and Software.
2014-10-29
WIP Standard
ARP6307
This document is for establishing and addressing anomalies on appearance of new and newly retreaded tires.
CURRENT
2014-10-28
Standard
J384_201410
This SAE Recommended Practice specifies performance requirements and test procedures for the strength and location of seat belt assembly anchorages. It applies to seat belt anchorages attached to vehicle body structure or to seat assemblies in the vehicle. Design Considerations are specified in SAE J383.
CURRENT
2014-10-27
Standard
J1545_201410
The practice applies to parts and materials used in vehicle manufacture which are intended to be acceptable color matches to a specified color standard. This practice is intended for use with parts or materials that are opaque or nearly so and does not apply to transparent materials. Materials covered by this practice include topcoat paint finishes, interior soft trim, interior and exterior hard trim, and exterior film.
CURRENT
2014-10-24
Standard
J1535_201410
This SAE Standard establishes uniform test procedures for the defrosting systems of off-road, self-propelled work machines used in construction, general purpose industrial, agricultural, and forestry machinery as referenced in table one of this document. It includes tests that can be conducted with uniform test equipment in commercially available laboratory facilities, as well as in an appropriate outdoor environment.
2014-10-23
WIP Standard
J973
This SAE Recommended Practice is intended to provide any technical person or group interested in ignition system design and/or evaluation with the specific equipment, conditions, and methods which will produce test results definitive and reproducible for his own work and yet sufficiently standardized to be acceptable to other groups working on battery ignition systems for automotive engines.
2014-10-09
WIP Standard
AIR5883A
This document defines the criteria used for the selection of landing gear shock strut upper and lower bearings. Common problems associated with shock strut bearings are presented.
Viewing 181 to 210 of 1688

Filter

  • Standard
    1688