Criteria

Text:
Content:
Display:

Results

Viewing 1621 to 1650 of 1686
HISTORICAL
1962-01-15
Standard
AS269C
This SAE Aerospace Standard (AS) provides material identification codes for aluminum alloys, copper alloys, carbon steels, alloy steels, titanium alloys, corrosion resistant materials, and heat resistant materials that are used to make AN, MS, and AS engine and propeller standard utility parts. This document also provides similar material codes for company parts (such as nuts, bolts, etc.) having design configuration similar to other company parts or the engine and propeller standard utility parts (AN, MS, and AS) that are not of the same material.
HISTORICAL
1961-08-15
Standard
ARP582
This SAE Aerospace Recommended Practice (ARP) covers the general requirements and test procedures for illuminating systems for integrally lighted aircraft instruments in order to provide (a) uniformity of illumination within each instrument, (b) legibility of instrument presentation under daylight or integral light, and (c) uniformity of illumination between instrument displays.
HISTORICAL
1961-06-01
Standard
J773_196106
This SAE Standard covers dimensional, material, and general specifications and methods of tests for two types of general purpose conical spring washers, designated type L and type H, for use as loose washers over screws and bolts, and also for use as pre-assembled washers in screw and washer assemblies.
HISTORICAL
1961-06-01
Standard
J588A_196106
This SAE Standard provides test procedures, requirements, and guidelines for turn signal lamps intended for use on vehicles of less than 2032 mm in overall width.
HISTORICAL
1961-06-01
Standard
J575_196106
This SAE Recommended Practice is intended as a guide toward standard practice and is subject to change to keep pace with experience and technical advances. This document provides standardized laboratory tests, test methods and equipment, and requirements for lighting devices covered by SAE Recommended Practices and Standards. It is intended for devices used on vehicles less than 2032 mm in width. Tests for vehicles larger than 2032 mm in overall width are covered in SAE J2139. Device specific tests and requirements can be found in applicable SAE technical reports.
HISTORICAL
1961-06-01
Standard
ARP693
This document includes requirements of installations of adequate landing and taxiing lighting systems in aircraft of the following categories: a) single engine personal and/or liaison type; b) light twin engine; c) large multiengine propeller; d) large multiengine turbojet; e) military high performance fighter and attack; and f) helicopter. The purpose of this document is to provide certain basic considerations and design criteria for installation of landing and taxiing light systems for night operation.
HISTORICAL
1961-03-01
Standard
J573_196103
Most lighting devices on motor vehicles today are required by law and are essential to operation on public roadways. Additionally, most lighting devices have replaceable light sources (bulbs). To assure field replacement, it is important that bulb types employed be readily available in normal service channels. This document attempts to define the physical, electrical, and photometric characteristics necessary to achieve a proper replacement for popular types of bulbs. Some of the design characteristics in this document are listed solely for the sake of standardization and are not intended to describe the performance of lighting devices (lamp assemblies) on the vehicle.
HISTORICAL
1960-07-01
Standard
AS665
No scope available.
HISTORICAL
1960-04-01
Standard
J586_196004
This SAE Standard provides test procedures, requirements, and guidelines for stop lamps intended for use on vehicles of less than 2032 mm in overall width.
HISTORICAL
1960-03-01
Standard
J580_196003
HISTORICAL
1960-03-01
Standard
J584_196003
This SAE Standard provides design parameter and general requirements for motorcycle headlamps.
HISTORICAL
1960-03-01
Standard
J592_196003
This SAE Standard provides test procedures, requirements, and guidelines for sidemarker lamps for vehicles less than 2032 mm in overall width.
HISTORICAL
1960-01-01
Standard
J566_196001
Headlamp Mountings - SAE Recommended Practice
HISTORICAL
1960-01-01
Standard
J565_196001
This SAE Standard provides test procedures, performance requirements, and guidelines for semiautomatic headlamp beam switching devices.
HISTORICAL
1960-01-01
Standard
J564_196001
This SAE Standard J564 defines the test conditions, procedures and performance specification for 6, 12, and 24 V manually actuated headlamp beam control switches.
HISTORICAL
1960-01-01
Standard
J576_196001
This SAE Recommended Practice provides test methods and requirements to evaluate the suitability of plastic materials intended for optical applications in motor vehicles. The tests are intended to determine physical and optical characteristics of the material only. Performance expectations of finished assemblies, including plastic components, are to be based on tests for lighting devices, as specified in SAE Standards and Recommended Practices for motor vehicle lighting equipment. Field experience has shown that plastic materials meeting the requirements of this document and molded in accordance with good molding practices will produce durable lighting devices.
HISTORICAL
1959-02-01
Standard
AS127C
HISTORICAL
1959-02-01
Standard
ARP373A
HISTORICAL
1959-02-01
Standard
J602_195902
This document applies to the requirements of a device used in the field and inspection stations to aim and check aim of mechanically aimable headlamp units. The purpose of this document is to provide a laboratory test procedure to determine whether the devices under test are capable of accurately positioning headlamp units from their aiming pads and maintaining their accuracy in service within the tolerances designated in this document.
HISTORICAL
1958-05-01
Standard
J578_195805
This SAE Standard defines and provides a means for the control of colors employed in motor vehicle external lighting equipment, including lamps and reflex reflectors. The document applies to the overall effective color of light emitted by the device in any given direction and not to the color of the light from a small area of the lens. It does not apply to pilot, indicator, or tell-tale lights.
HISTORICAL
1958-05-01
Standard
J577_195805
This SAE Recommended Practice provides procedures, and information to conduct vibration (impact) tests on lighting devices and their components as well as other safety equipment used on vehicles.
HISTORICAL
1954-12-15
Standard
AS264C
The desired system for aircraft instrument panel and cockpit lighting is one that will furnishlight of adequate intensity and distribution under all conditions of external lighting so that the crew may read instrumentation, placards, check lists, manuals, maps, instrument color coding, distinguish controls, etc., without undue interference with their vision outside of the aircraft.
HISTORICAL
1954-12-01
Standard
AS41D
No scope available.
HISTORICAL
1953-04-15
Standard
ARP277
HISTORICAL
1952-10-15
Standard
AS271
HISTORICAL
1950-05-01
Standard
AS93C
No scope available.
HISTORICAL
1950-04-01
Standard
AS41C
No scope available.
HISTORICAL
1950-04-01
Standard
AS93B
No scope available.
Viewing 1621 to 1650 of 1686

Filter

  • Standard
    1686