Criteria

Text:
Content:
Display:

Results

Viewing 91 to 120 of 1669
2016-03-15
WIP Standard
AIR6411
Provide information and guidance for landing gear operation in cold temperature environment. Covers all operational aspects on ground and in flight. Includes effects on: tires, wheels, brakes, shock strut, seals, and actuation.
2016-03-14
WIP Standard
AS6409
Provide specifications for hydraulic fluids used in landing gear shock struts. Some of this information was previously in AIR5358 however specifications should be in an AS. This new document will contain the appropriate specifications for premixed hydraulic fluid with additives believed to improve fluid performance and reduce friction.
2016-03-14
WIP Standard
AS6410
This document was requested by the FAA to provide a technical update of TSO-C26d to address Electric Brake Actuation, standardize with TSO-C135a and address any remaining concerns with the current technical requirements in AIR5381.
2016-03-11
WIP Standard
ARP6408
The purpose of this SAE Aerospace Recommended Practice (ARP) is to provide a reasonable definition of external hydraulic fluid leakage exhibited by landing gear shock absorbers. The definition will outline normal and excessive leakage that is measureable and routinely encountered in newly assembled refurbished/remanufactured components, leakage during acceptance flights, recently delivered and in-service aircraft.
CURRENT
2016-03-11
Standard
J578_201603
This SAE Standard defines and provides a means for the control of colors employed in motor vehicle external lighting equipment, including lamps and reflex reflectors. The document applies to the overall effective color of light emitted by the device in any given direction and not to the color of the light from a small area of the lens. It does not apply to pilot, indicator, or tell-tale lights.
CURRENT
2016-03-05
Standard
AIR5689B
This SAE Aerospace Information Report (AIR) provides definitions of and inspection criteria for defects commonly encountered in molded glass covers for exterior aircraft lighting.
2016-02-29
WIP Standard
J280
This standard provides test methods and requirements for snowmobile headlamps.
2016-02-29
WIP Standard
J279
The SAE document provides test methods and requirements for tail lamps for snowmobiles.
2016-02-29
WIP Standard
J278
This document provides test methods and requirements for the stop lamp on snowmobiles.
2016-02-28
WIP Standard
J1957
This SAE Standard provides test procedures, performance requirements, and guidelines for center high mounted stop lamps (CHMSL) for use on vehicles less than 2032 mm in overall width.
2016-01-26
WIP Standard
ARP711C
This Aerospace Recommended Practice (ARP) covers the general design and performance characteristics of illuminated information signs for service in the passenger compartment of passenger transport aircraft. "Illuminated information signs" are lighted signs used to inform occupants of the passenger compartment. Signs may use symbols or letters to convey messages. This ARP does not apply to "EXIT" signs which are the subject of ARP503.
CURRENT
2016-01-20
Standard
J1432_201601
This SAE Recommended Practice provides test procedures, requirements, and guidelines for high-mounted stop lamps and high-mounted turn signal lamps intended for use on vehicles 2032 mm or more in overall width. This document applies to trucks, motor coaches, van type trailers, and other vehicles with permanent structure greater than 2800 mm high. This document does not apply to school buses, truck tractors, pole trailers, flat-bed trailers, pick-up truck with dual wheels and trailer converter dollies. The purpose of the high-mounted stop lamp(s) and high-mounted turn signal lamp(s) is to provide a signal over intervening vehicles to the driver of following vehicles.
CURRENT
2016-01-20
Standard
J2040_201601
This SAE Standard provides test procedures, requirements, and guidelines for tail lamps intended for use on vehicles 2032 mm or more in overall width. Tail lamps conforming to the requirements of this document may also be used on vehicles less than 2032 mm in overall width.
2016-01-18
WIP Standard
ARP4101/8A
This document recommends criteria for standardization of flight deck interior doors and their operation which will provide optimum use under normal and emergency conditions.
2016-01-05
WIP Standard
AIR5885A
This document outlines the most common repairs used on landing gear components. It is not the intention of this AIR to replace Overhaul/Component Maintenance or Technical Order Manuals, but it can serve as a guide into their preparation. This document may also be used as a template to develop an MRB (Material Review Board) plan. The recommendations in this document apply to components made of metallic alloys. These recommendations are intended for new manufactured components as well as for overhauled components. The extent of repair allowed for new components as opposed to in-service components is left to the cognizant engineering authorities. Reference could be made to this document when justifying repairs on landing gears. For repairs outside the scope of this document, a detailed justification is necessary. It must be understood that all the repairs listed in this document are not to be applied without the involvement of the cognizant engineer.
2016-01-04
WIP Standard
AIR5552A
This information report provides general guidance for the design considerations, qualification in endurance, strength and fatigue of landing gear using composite components as principle structural elements. The information discussed herein includes the development and evaluation of design data considering: the potential for imbedded manufacturing defects, manufacturing process variations, the component operating environment, potential damage threats in service, rework and overhaul, and inspection processes. This AIR mainly discusses the use of thick composites for landing gear structural components. Considerations and recommendations provided in this AIR may therefore differ greatly from considerations and recommendations found in widely accepted composite design references such as CMH-17 and Advisory Circulars such as AC 20-107(B).
2016-01-03
WIP Standard
AIR6900
This AIR will address the need for a strategy to achieve aircraft operating certificate holder maintenance efficiencies within the existing regulatory environment as well as the need for regulation, policy, and guidance changes in the long-term to accommodate more complex IVHM solutions. This document will analyse which IVHM solutions can be incorporated within existing maintenance procedures and which also comply with regulations, policy, and guidance. One of the AIR’s objectives is to define best practices for aircraft operating certificate holders to engage with regulators to get approval for simpler IVHM applications leading to maintenance efficiencies. Additionally, this document will analyse the barriers that existing regulations, policy, and guidance present to the implementation of more advanced IVHM solutions. The result is a set of recommendations to certify and implement end-to-end IVHM solutions for the purpose of gaining maintenance efficiencies.
CURRENT
2015-12-27
Standard
AIR5631A
The purpose of this document is to provide a listing for current commercial and military aircraft landing gear systems and their types and manufacturers. Data has been provided for the following commercial aircraft types; wide body jet airliners, narrow body jet airliners, and turboprop/commuter aircraft and the following military aircraft types; fighter, bomber, cargo, attack, surveillance, tanker and helicopter categories. The aircraft that have been included in this document are in operational service either with airlines, business, cargo or military operators. No information is presented for aircraft that are currently being developed or that are not in extensive usage. This document will provide an informational reference for landing gear engineers to access when evaluating other gear and aircraft systems. Future revisions of this document will add aircraft as they enter into service.
CURRENT
2015-12-27
Standard
AIR6246
This SAE Aerospace Information Report (AIR) will review new landing gear (engine off) taxi system technologies currently being developed by various companies and describe the basic design concepts and potential benefits and issues. This AIR will identify the associated systems that could be affected by this new technology. The document will review basic design and operational requirements, failure modes and identify system certification requirements that may need to be addressed. The technology is evolving as this paper is being written and the data present is currently up to date as of 2015.
CURRENT
2015-12-04
Standard
ARP503G
This SAE Aerospace Recommended Practice (ARP) provides criteria for design and location of power supplies, controls, light fixtures, and associated equipment which are used to provide emergency illumination in transport aircraft, designed to comply with 14 CFR part 25 (Reference 1) for operation under 14 CFR part 91 (Reference 11) and 14 CFR part 121 (Reference 2), and also in compliance with FAA Advisory Circulars AC25.812-1A (Reference 3) and AC25.812-2 (Reference 10). It is not the purpose of an ARP to specify design methods to be followed in the accomplishment of the stated objectives.
2015-12-03
WIP Standard
AIR1594D
This document is intended to give advisory information for the selection of plain bearings and bearing materials most suitable for aircraft landing gear applications. Information included herein was derived from bearing tests and service experience/reports. Airframe/landing gear manufacturers, commercial airlines, the U.S. Air Force and Naval Air Systems Command provided input for the document.
CURRENT
2015-11-05
Standard
J599_201511
This code is intended only for the inspection and maintenance of lighting equipment on motor vehicles that are in use.
2015-11-04
WIP Standard
J2918
This SAE Recommended Practice establishes uniform test procedures and per¬formance requirements for engine-off heating, ventilation, and air conditioning (HVAC) systems in order to achieve driver thermal comfort in both winter and summer rest periods. This specification will apply to heavy trucks with and without sleeper compartments, including but is not limited to Class 6, 7, and 8 powered vehicles.
2015-11-04
WIP Standard
J2646
This SAE recommended practice establishes a uniform test procedures for on highway trucks equipped with an air-conditioning system used to condition the air in the cabin and sleeper compartment of the vehicle. This specification will apply to heavy trucks with and without sleeper compartments.
CURRENT
2015-10-28
Standard
J1319_201510
This SAE Recommended Practice provides test procedures, requirements, and guidelines for rear fog lamp systems.
CURRENT
2015-10-28
Standard
J1373_201510
This SAE Recommended Practice provides test procedures, requirements, and guidelines for rear cornering lamps for use on vehicles less than 9.1 m in overall length.
Viewing 91 to 120 of 1669

Filter

  • Standard
    1669