Criteria

Text:
Topic:
Content:
Display:

Results

Viewing 1 to 30 of 342
CURRENT
2017-11-21
Standard
AMS4916L
This specification covers a titanium alloy in the form of sheet, strip, and plate up through 4.000 inches (101.60 mm) inclusive in thickness (see 8.6).
2017-09-26
WIP Standard
G17AC
This specification covers a titanium alloy in the form of sheet from 0.020 to 0.1874 inches (0.508 to 4.760 mm), inclusive, nominal thickness.
2017-09-22
WIP Standard
AMS6946D
This specification covers a titanium alloy in the form of sheet, strip, and plate.
2017-09-22
WIP Standard
AMS6945C
This specification covers a titanium alloy in the form of sheet, strip, and plate. <p> These products have been used typically for parts requiring strength up to 750 °F (400 °C), but usage is not limited to such applications.
2017-09-22
WIP Standard
AMS4985F
This specification covers a titanium alloy in the form of investiment castings.
2017-09-22
WIP Standard
AMS4992C
This specification covers titanium Ti 6Al-4V alloy in the form of investment castings.
2017-09-22
WIP Standard
AMS4991F
This specification covers a titanium alloy in the form of investment castings having four grades of permissible discontinuities.
2017-09-22
WIP Standard
AMS4989D
This specification covers a titanium alloy in the form of sheet, strip, and plate.
2017-09-22
WIP Standard
AMS4967M
This specification covers a titanium alloy in the form of bars, wire, forgings, flash welded rings up through 4.000 inches (101.60 mm) in diameter or least distance between parallel sides and stock of any size for forging, heading, or flash welded rings (See 8.6).
2017-09-22
WIP Standard
AMS4919J
This specification covers a titanium alloy in the form of sheet, strip, and plate 0.025 to 3.000 inches (0.64 to 76.20 mm), inclusive, in nominal thickness.
2017-09-22
WIP Standard
AMS4914G
This specification covers a titanium alloy in the form of sheet and strip up to and including 0.125 inches in thickness. These products have been used typically in applications requiring high strength-to-weight ratio and stability up to 550 °F (288 °C), but usage is not limited to such applications. Parts are typically formed in the solution heat treated condition and subsequently precipitation heat treated to final condition.
2017-09-22
WIP Standard
AMSH81200E
This specification covers the heat treatment of titanium and titanium alloy mill products (raw material), including wrought and cast products, by material producers. This specification also covers furnace equipment requirements, test procedures, and general information for heat treating procedures, heat treating temperatures, and material test procedures for the heat treatment of titanium and titanium alloys. It also describes procedures that, when followed, have produced the desired properties within the limitations of the respective alloys.
2017-07-19
WIP Standard
G17AB
This specification covers a titnaium alloy in the form of forgings 4.4 inches (111.76 mm) and under in nominal diameter or least distance between parallel sides and forging stock of any size.
2017-04-26
WIP Standard
AMS4988D
This specification covers a titanium alloy in the form of sheet, strip, and plate in thicknesses up through 4.000 inches (101.60 mm).
2017-04-26
WIP Standard
AMS7819E
This specification covers an arc-cast molybdenum alloy in the form of round bars. These bars have been used typically for parts requiring high modulus and uniform strength up to 2300 °F (1260 °C) but usage is not limited to such applications. This alloy is not recommended for use in oxidizing atmospheres above 1000 °F (540 °C) unless protected by a suitable coating.
2017-04-26
WIP Standard
AMS6905C
This specification covers a titanium alloy in the form of bars and forgings up through 3.000 inches (76.20 mm), inclusive, in diameter or least distance between parallel sides with a maximum cross-sectional area of 10 square inches (64.5 cm2), and forging stock of any size.
2017-04-26
WIP Standard
AMS6930F
This specification covers a titanium alloy in the form of bars, forgings, and stock for forging.
2017-04-26
WIP Standard
AMS4907L
This specification covers a titanium alloy in the form of sheet, strip, and plate. These products have been used typically for parts requiring a combination of weldability, ductility, and good notch-toughness down to –423 °F (–253 °C), but usage is not limited to such applications. Certain processing procedures and service conditions may cause these products to become subject to stress corrosion cracking; ARP982 recommends practices to minimize such conditions.
2017-04-26
WIP Standard
AMS4965M
This specification covers a titanium alloy in the form of bars, wire, forgings, and flash welded rings 4.000 inches (101.60 mm) and under in nominal diameter or least distance between parallel sides and of stock for forging and flash welded rings.
2017-04-26
WIP Standard
AMS4958E
This specification covers a titanium alloy in the form of bars and rods 1.00 inch (25.4 mm) and under in nominal diameter.
2017-04-26
WIP Standard
AMS6931D
This specification covers a titanium alloy in the form of bars and forgings up through 10.000 inches (254.00. mm), inclusive, in diameter or least distance between parallel sides with a maximum cross-sectional area of 79.0 in2 (506.45 cm2) and forging stock of any size (see 8.7).
2017-04-26
WIP Standard
AMS4945G
This specification covers a titanium alloy in the form of seamless tubing.
2017-04-26
WIP Standard
AMS4911P
This specification covers a titanium alloy in the form of sheet, strip, and plate up through 4.000 inches (101.60 mm) inclusive in thickness.
2017-04-04
WIP Standard
AMS4898E
This specification covers a titanium alloy in the form of sheet in nominal thicknesses 0.016 through 0.1874 inch (0.41 through 4.760 mm).
2017-04-04
WIP Standard
AMS4902L
This specification covers one grade of commercially-pure titanium in the form of sheet, strip, and plate up through 1.000 inch (25.40 mm). This material typically has been used for parts requiring aqueous corrosion resistance, moderate strength up to 400 °F (204 °C) and oxidation resistance up to 600 °F (316 °C), but usage is not limited to such applications.
2017-04-04
WIP Standard
AMS4978H
This specification covers a titanium alloy in the form of bars, wire, forgings, flash welded rings 4.000 inches (101.60 mm) and under in diameter, or least distance between parallel sides and stock of any size for forging or flash welded rings (see 8.6).
2016-10-08
WIP Standard
AMS2244D
This specification covers established manufacturing tolerances applicable to titanium and titanium alloy tubing. These tolerances apply to all conditions, unless otherwise noted. The term "excl" is used to apply only to the higher figure of the specified range.
2015-09-27
WIP Standard
AMS2809B
This specification covers procedures for identifying wrought products of titanium and titanium alloys.
CURRENT
2015-07-06
Standard
AMS7909C
This specification covers aluminum-beryllium powders consolidated by hot isostatic pressing (HIP) into the form of blocks, blanks or shapes.
2015-03-31
WIP Standard
G15AA
New AMS for Ti-6-4 Seamless, Hydraulic Tubing including Technical, Quality and Testing Requirements
Viewing 1 to 30 of 342

Filter

  • Standard
    342