Criteria

Text:
Sector:
Content:
Display:

Results

Viewing 1 to 30 of 619
2017-09-22
WIP Standard
AMS4914G
This specification covers a titanium alloy in the form of sheet and strip up to and including 0.125 inches in thickness. These products have been used typically in applications requiring high strength-to-weight ratio and stability up to 550 °F (288 °C), but usage is not limited to such applications. Parts are typically formed in the solution heat treated condition and subsequently precipitation heat treated to final condition.
2017-09-22
WIP Standard
AMS4919J
This specification covers a titanium alloy in the form of sheet, strip, and plate 0.025 to 3.000 inches (0.64 to 76.20 mm), inclusive, in nominal thickness.
2017-09-22
WIP Standard
AMS4967M
This specification covers a titanium alloy in the form of bars, wire, forgings, flash welded rings up through 4.000 inches (101.60 mm) in diameter or least distance between parallel sides and stock of any size for forging, heading, or flash welded rings (See 8.6).
2017-09-22
WIP Standard
AMS4985F
This specification covers a titanium alloy in the form of investiment castings.
2017-09-22
WIP Standard
AMS4991F
This specification covers a titanium alloy in the form of investment castings having four grades of permissible discontinuities.
2017-09-22
WIP Standard
AMS4989D
This specification covers a titanium alloy in the form of sheet, strip, and plate.
2017-09-22
WIP Standard
AMS4992C
This specification covers titanium Ti 6Al-4V alloy in the form of investment castings.
2017-09-22
WIP Standard
AMS6946D
This specification covers a titanium alloy in the form of sheet, strip, and plate.
2017-09-22
WIP Standard
AMS6945C
This specification covers a titanium alloy in the form of sheet, strip, and plate. <p> These products have been used typically for parts requiring strength up to 750 °F (400 °C), but usage is not limited to such applications.
2017-09-22
WIP Standard
AMSH81200E
This specification covers the heat treatment of titanium and titanium alloy mill products (raw material), including wrought and cast products, by material producers. This specification also covers furnace equipment requirements, test procedures, and general information for heat treating procedures, heat treating temperatures, and material test procedures for the heat treatment of titanium and titanium alloys. It also describes procedures that, when followed, have produced the desired properties within the limitations of the respective alloys.
2017-09-20
WIP Standard
D17AC
This specification covers a copper-nickel-tin alloy in the form of back-extruded mechanical tube 1.100 to 13.6 inches (28 to 330 mm) in outer diameter. .
2017-09-15
WIP Standard
D17AA
This specification covers the specific requirements for 2017 aluminum alloy bar, rod and wire produced by rolling, drawing or cold finishing supplied in the annealed (O temper) condition (see 8.4). When specified, product shall be supplied in the “as fabricated” (F) temper.
2017-07-24
WIP Standard
AMSWWT700/5B
This specification covers the specific requirements for seamless tube drawn from aluminum alloy 5086.
2017-07-24
WIP Standard
AMSWWT700B
This specification covers the general requirements for aluminum and aluminum alloy tube; drawn, seamless (see 6.1.1). Specific requirements for these products in a particular alloy are covered by the applicable detail specification (see 6.3).
2017-07-19
WIP Standard
G17AB
This specification covers a titnaium alloy in the form of forgings 4.4 inches (111.76 mm) and under in nominal diameter or least distance between parallel sides and forging stock of any size.
2017-06-23
WIP Standard
D17AB
This revises the Identification section of the General Agreement on Marking.
2017-05-30
WIP Standard
AMS4478A
This specification covers an aluminum alloy in the form of Alclad sheet and plate supplied in the –T81/-T851 temper. These products have been used typically for high strength parts requiring higher yield strength than is afforded by naturally aged tempers of this alloy and maximum corrosion resistance and whose fabrication does not involve welding, but usage is not limited to such applications.
2017-05-16
WIP Standard
GA-G17AA
Add ASTM E 539
2017-05-10
WIP Standard
AMS4403A
This specification covers an aluminum alloy in the form of die forgings 12 inches (305 mm) and under in nominal thickness and of forging stock.
2017-05-10
WIP Standard
AMS4820F
This specification covers bearings of leaded copper cast on one or both faces of a steel backing.
2017-05-10
WIP Standard
AMS4800F
This specification covers bearings of a tin alloy cast on one or both faces of a steel or bronze backing.
2017-05-10
WIP Standard
AMS4827F
This specification covers bearings of a leaded bronze cast on one or both faces of a steel backing.
2017-05-10
WIP Standard
AMS4463A
This specification covers an aluminum alloy in the form of plate.
2017-05-10
WIP Standard
AMS4597B
This specification covers a copper-nickel-tin alloy in the form of bars and rods.
2017-05-02
WIP Standard
AMS4268A
This specification covers an aluminum alloy in the form of sheet and plate supplied in the -T81/-T851.
2017-05-02
WIP Standard
AMS4462A
This specification covers an aluminum alloy in the form of alclad sheet and plate supplied in the -T3/-T351 temper.
2017-05-02
WIP Standard
AMS4269A
This specification covers an aluminum alloy in the form of sheet and plate supplied in the -T361 temper.
2017-05-02
WIP Standard
AMS4477A
This specification covers an aluminum alloy in the form of coiled sheet supplied in the –T4 temper.
2017-05-02
WIP Standard
AMS4475B
This specification covers an aluminum alloy in the form of alclad coiled sheet supplied in the –T4 temper. These products have been used typically for medium strength parts requiring formability and maximum corrosion resistance and whose fabrication does not involve welding, but usage is not limited to such applications.
2017-05-02
WIP Standard
AMS4461A
This specification covers an aluminum alloy in the form of sheet and plate supplied in the annealed (O) condition. When specified, product shall be supplied in the “as fabricated” (F) temper.
Viewing 1 to 30 of 619

Filter

  • Aerospace
    619
  • Standard
    619