Criteria

Text:
Content:
Display:

Results

Viewing 1 to 30 of 2533
CURRENT
2017-11-20
Standard
AMSQQA200/4C
This specification covers the specific requirements for aluminum alloy 5083 bar, rod, shapes, tube, and wire produced by extrusion.
2017-11-17
WIP Standard
AMSWWT700/3B
This specification covers the specific requirements for seamless tube drawn from aluminum alloy 2024.
2017-11-17
WIP Standard
AMSWWT700/4B
This specification covers the specific requirements for seamless tube drawn from aluminum alloy 5052.
2017-11-17
WIP Standard
J451
This information report is intended to give general data on the properties of aluminum and information on working, joining, forming, machining, finishing, and heat treating of aluminum.
2017-11-17
WIP Standard
J454
The SAE Standards for wrought aluminum alloys cover materials with a considerable range of properties and other characteristics, but do not include all of the commercially available materials. If none of the materials listed in Tables 1 through 7 provides the characteristics required by a particular application, users may find it helpful to consult with the suppliers of aluminum alloy products. See companion document, SAE J1434.
2017-11-17
WIP Standard
J459
The bearing performance of steel backed half bearings, bushings, and washers is dependent on the properties and thickness of the lining alloys, the strength and dimensional stability of the steel backing (usually SAE 1010) and the strength of the bond between the lining alloy and the backing. This SAE Information Report is primarily concerned with the properties of the lining alloys used in automotive applications, in particular, the crankshaft bearings of the internal combustion engine.
2017-11-17
WIP Standard
J1434
This report approaches the material selection process from the designer's viewpoint. Information is presented in a format designed to guide the user through a series of decision-making steps. "Applications criteria" along with engineering and manufacturing data are emphasized to enable the merits of aluminum for specific applications to be evaluated and the appropriate alloys and tempers to be chosen.
2017-11-17
WIP Standard
J1755
The scope of this SAE Recommended Practice is to give guidelines for design, processing, and material selection for stainless steel and bimetal exterior automotive moldings.
2017-11-17
WIP Standard
J452
The SAE Standards for aluminum casting alloys cover a wide range of castings for general and special use, but do not include all the alloys in commercial use. Over the years, aluminum alloys have been identified by many numbering systems as shown in Table 1. Presently, SAE is recommending the use of the UNS Numbering System to identify these materials. The castings are made principally by sand cast, permanent mold, or die cast methods; however, shell molding, investment casting, plaster cast, and other less common foundry methods may also be used. If the alloys listed do not have the desired characteristics, it is recommended that the manufacturers of aluminum castings be consulted.
2017-11-16
WIP Standard
AMS7721D
This specification covers a lead alloy in the form of sheet and extrusions.
2017-11-16
WIP Standard
AMSDTL22499/1B
No scope available.
2017-11-15
WIP Standard
J457
This SAE Standard for wrought aluminum alloys provides sources of chemical and mechanical property data for a considerable range of alloys with varying properties, structures, and applications.
2017-11-15
WIP Standard
J460
Compositions apply to the finished bearing or bearing lining, not necessarily to the alloy at an intermediate processing stage. All values not given as ranges are maxima.
2017-11-15
WIP Standard
J993
This standard provides systems for designating wrought aluminum and wrought aluminum alloys, aluminum and aluminum alloys in the form of castings and foundry ingot, and the tempers in which aluminum and aluminum alloy wrought products and aluminum alloy castings are produced.
CURRENT
2017-11-13
Standard
AMS4269A
This specification covers an aluminum alloy in the form of sheet and plate supplied in the -T361 temper.
CURRENT
2017-11-13
Standard
AMS4475B
This specification covers an aluminum alloy in the form of alclad coiled sheet from 0.010 to 0.128 inches, incl (0.25 to 3.25 mm, incl) in thickness supplied in the –T4 temper (see 8.5).
CURRENT
2017-11-08
Standard
AMS4403A
This specification covers an aluminum alloy in the form of die forgings 1.000 to 12.000 inches inclusive (25 to 305 mm) in nominal thickness at the time of heat treatment and of forging stock (see 8.4).
CURRENT
2017-11-03
Standard
AMS4193D
This specification covers an aluminum alloy in the form of flat sheet and plate 0.500 inch (12.70 mm) and under in nominal thickness.
CURRENT
2017-11-03
Standard
AMS4477A
This specification covers an aluminum alloy in the form of coiled sheet supplied in the –T4 temper.
2017-10-28
WIP Standard
AMSQQA367E
This specification covers aluminum alloy die forgings and hand forgings.
2017-10-28
WIP Standard
AMS4277B
This specification covers an aluminum alloy in the form of sheet whose grain size shall be ASTM No 6 or finer.
2017-10-28
WIP Standard
AMS4326A
This specification covers an aluminum alloy in the form of extruded bars, rods, and integrated profiles.
2017-10-28
WIP Standard
AMS4408A
This specification covers an aluminum alloy in the form of plate.
2017-10-28
WIP Standard
AMS4276B
This specification covers an aluminum alloy in the form of sheet with fine grain structure.

This sheet has been used typically for severely-formed structural parts which will be subsequently heat treated and painted or otherwise protected from corrosion, but usage is not limited to such applications.

2017-10-28
WIP Standard
AMS4456A
This specification covers an aluminum alloy in the form of hand forgings 11 inches (280 mm) and under in nominal thickness, and of forging stock.
2017-10-28
WIP Standard
AMS4482A
This specification covers a dilute aluminum/TiB2 metal matrix composite in the form of sand castings.
2017-10-28
WIP Standard
AMS7731D
This specification covers pure gold in the form of wire and ribbon.
2017-10-28
WIP Standard
AMSA22771D
The initial SAE publication of this document was taken directly from U.S. Military Standard MIL-A-22771D. This SAE Standard may retain the same part numbers established by the original military document. Any requirements associated with Qualified Products Lists (QPL) may continue to be mandatory for DoD contracts. Requirements relating to QPLs have not been adopted by the SAE for this standard and are not part of this SAE document.
2017-10-28
WIP Standard
AMS4332A
This specification covers an aluminum alloy procured in the form of extruded profiles (shapes) with cross-sections up to 0.750 inch (19.05 mm).
Viewing 1 to 30 of 2533

Filter

  • Standard
    2533